jo62

K3DPrint

Georgia Bulldogs - Thor&#39;s HammerThis is a Bulldogs themed Thor&#39;s hammer. It is separated into three plates so that it can be printed easily. I think after many tests and small alterations, I have come up with a really good profile for this. I sacrificed a little bit of time to get a more durable, better quality result that can be handled fairly rough, haha.&nbsp;Credits:@ChaosCoreTech (Original Hammer Designer) - <a target="_blank" href="https://www.thingiverse.com/thing:1311108" rel="nofollow noopener">https://www.thingiverse.com/thing:1311108</a> @Emp3thy (Hammer Remix) - <a target="_blank" href="https://makerworld.com/en/models/44616?from=search#profileId-46284" rel="nofollow noopener">https://makerworld.com/en/models/44616?from=search#profileId-46284</a>@Burnnoticed (Remix /w NFL Branding) - <a target="_blank" href="https://makerworld.com/en/models/166035?from=search#profileId-182300" rel="nofollow noopener">https://makerworld.com/en/models/166035?from=search#profileId-182300</a>@3DHummel (Rock Stand - 75%) - <a target="_blank" href="https://www.printables.com/model/132359-thors-hammer-molnjir-life-size-with-better-handle-" rel="nofollow noopener">https://www.printables.com/model/132359-thors-hammer-molnjir-life-size-with-better-handle-</a>&nbsp;Changes:My remix fixes quite a few issues I had with the original NFL hammers.<ul><li>I was able to get rid of the slight line that ran down the middle when printed.</li><li><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000457099/design/2024-03-17_1272c464126ee.png"></li><li>No more removing a mess of supports from the inside.</li><li><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000457099/design/2024-03-17_619b6f81bc59c.png"></li><li>The handle has been changed/re-oriented. This uses a bit more supports, but it provides a clean connection to the bottom of the hammer. I have printed lots of these for friends and family, and we had a few break off at that point. This change seems to end up with a sturdier hammer.</li><li><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000457099/design/2024-03-17_f7e1b8c6bcb92.png"></li><li>The “top cap” has had the lettering removed. At 75%, the quality suffered, and this just provides a cleaner look, especially with a textured plate.</li><li>I replaced the bottom cap with a different design, that sits flush with the side of the handle. This helps prevent the top pieces from snapping off.</li><li><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000457099/design/2024-03-17_2b585605f3c8c.png"></li></ul>&nbsp;&nbsp;Upcoming<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000457099/design/2024-03-17_70e70db0372c1.png">Currently in test print. The original model had some uneven areas for the handle to connect. This caused it to not sit flush with the bottom, I have fixed that and will update the model once it is tested.

Georgia Bulldogs - Thors Hammer

XO Clients

lukeofhazzard

A bust / sculpture of the Dude (Jeff Bridges) from the movie "Big Lebowski", made in Blender.I wouldn't print the bust any smaller than in the STL provided. Tree Supports are definitely your friend here (be extremely careful when removing the supports from the sunglasses, it's a bit tricky but works well).

The Big Lebowski - The Dude - Bust

Gifts

alexander.feldhaus

Its just a simple model of an organizer for my desk.print with 0,6 nozzle&nbsp;

Simple Desk Organizer which fits DinA4 Paper

Home

ShearLab

This Harry Potter's wand is printed in one piece and is about 20cm long. It's printed at an angle to provide the best structural strength and to avoid any plate textures transferring onto it.&nbsp;As per Bambu Lab recommendations, it is highly recommended to dry your filaments before printing to avoid issues (especially at the tip/ end of the print).&nbsp;Drying Requirements Wiki Page: <a target="_blank" href="https://wiki.bambulab.com/en/general/filament-guide-material-table#storage-and-material-specifications" rel="nofollow noopener">https://wiki.bambulab.com/en/general/filament-guide-material-table#storage-and-material-specifications</a>&nbsp;&nbsp;&nbsp;&nbsp;

Harry Potter's Wand

Kids

Sakul

📐Corner Clamp for Woodworking🪚 I needed some corner clamps for a woodworking project that I&#39;m currently working on.Most of the corner clamps I found still needed a traditional one-hand clamp for tightening, so I designed my own that are fully 3D printed and don&#39;t need additional parts. I increased the wall count a little bit in the print profile to ensure that the parts are strong enough. The thread in the rail may look a bit rough after printing, but it worked like a charm without post-processing.  You may also like: <figure class="table" style="width: 98.39%"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image"><a href="https://makerworld.com/en/models/484385#profileId-396742" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000176297/design/2024-06-04_8706199eaa5e9.jpg"></a><figcaption>🍦Pop &amp; Catch Toys Ice Cream Cone🍦</figcaption></figure></td><td><figure class="image"><a href="https://makerworld.com/en/models/447981#profileId-354736" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000176297/design/2024-05-01_1338867632a42.jpg"></a><figcaption>🐷Minecraft Animal Farm Pack🐮</figcaption></figure></td></tr></tbody></table></figure>