jmendezfl

Zemlin

After reading a few more remix comments, I see the glass issue isn't an anomaly on my print, so I updated the STP, STL, and .3MF models to include the 1mm (0.25%) front-to-back stretch. As a guy with a career in product design, let me first say that Ben did a really nice job on this riser design. There's a lot of thought, time, and effort in this design. After printing a copy, I did have a couple of issues. After trying to figure out quick fixes, I went down the remix rabbit hole and the attached files are the result. The biggest issue I had was the top glass did not fit in the riser. I discovered that the radius of the back corners is larger than the glass corners, so it prevented the glass from seating against the back wall. I added some relief back there with a smaller radius corner to let the glass slide back a little further. In my final print I also stretched the models by .25% to add 1mm to the overall length. I also like the idea of a front ledge, so I added that to the front dash parts and the gaskets. The plugs on the gaskets had no really retention into the body parts, so I added a little more bump on the plugs so they snap in. The buttons up front are free to rotate, so I added keys on the buttons and the X1C frame to keep them oriented properly. Not a fan of coming off the build plate in a full radius, so I modified the back-side of the riser so the build comes off the plate a 45 degrees. Cleans up the first few layers on the butt. I noticed the build plates in the storage slot would walk out of the riser with the machine shaking. I added a little slide latch on one side to keep the build plates in place. I used glass filled ABS on my build. The spring element on the latch might need to be tweaked to get a nice snap/lock in other materials. I printed some latches in PLA and they work great. Regardless of the material you use, coat the center leg of the latch slide with super-glue - top and bottom. Dab off the excess with a paper towel. Let it cure for a good while before installing it. That will add a lot of strength across the layer lines of the spring so it doesn't break. You may also need to spread the slot a little when sliding that latch into position. I know PETG is a popular material for these risers. If you use PETG for Part2, I suggest NOT using PETG for the slide. PETG does not slide well plastic on plastic. PLA will work better. I ended up with the 8mm strip lights rather than the 5mm Ben suggests. Not sure how I screwed that up, but I reworked the slots to fit the 8mm lights. My strip is also cut at 50mm intervals, so I stretched the slots out further to the front to better match the 50mm increment. Happy to provide hybrid models if anyone wants them - like if you want the features for my build plate slide with the original lighting slots.

AMS Riser - Zemlin Remix

fay3dlab

Im currently upgrading most of my suspended models to include channel to install led strips in them.. So for the suspended star destroyer V2.. since its already in 2 parts.. i added a channel path so you can install a LED strips around the outer frame.. and i put small holes in the inner frame so that the lights from the LED shines through to the ship..&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/516767/2024-01-01_27386ae7989a8.gif"></figure>&nbsp;If you're interested in getting the LED strips.. here's my affiliate link to buy it.. 5V USB RGB LED Strip Light https://s.click.aliexpress.com/e/_oEk0hDa &nbsp;The ship itself is modelled by nikoli2803 from thingerverse.. the circular frame is the imperial logo itself.. the whole frame i modelled it to look like the deathstar.. everything was done using Tinkercad..&nbsp;The ship itself comes in 2 parts.. front and back.. and there are 3 clips to hold both side of the ship together.. the bottom clip will be the stand for the whole suspended star destroyer and the 2 clips works on any side..Its a bit tricky to assemble since you cant put both parts of the ship down since its suspended on the strings..<ul><li>so my suggestion is to put the bottom clip down on a table and then put the 2 parts into the clip..</li><li>it should fit snuggly together..</li><li>once the frame can stand on its own.. you can put the other 2 clips onto the frame..</li></ul>When printing suspended models.. one important thing to remember is to set the wall generator to arachne from classic.. this will make the slicer print the strings..&nbsp;I hope you guys have fun printing this new version of the suspended imperial star destroyer..

Suspended Star Destroyer V2 LED strips

Household / Decor

fractalnoise

Large Imperial Basilica ruins for 6mm/epic scale tabletop wargaming&nbsp;My other Epic Scale Terrain projects:<a target="_blank" href="https://makerworld.com/en/u/3965042544/collections/116782" rel="nofollow noopener">https://makerworld.com/en/u/3965042544/collections/116782</a>

Epic Scale Terrain: Large Basilica Ruins

Wargame Terrain

Electronics

Imagination Forge 3D

#####MAKE SURE TO FOLLOW MY PROFILE AS I WILL BE RELEASING MORE DESIGNS!#####🎲 Unleash the Crits: The Ultimate 3D-Printable Dice Box! 🎲Adventurers, Game Masters, and Dice Goblins rejoice! Introducing the latest treasure in your gaming arsenal - a meticulously designed dice box that's as functional as it is fantastical. Carved (digitally, of course) from the ether of imagination, this 3D-printable marvel is your new best friend on the tabletop battlefield.Epic Design, Mythic Quality: This isn't just any dice box; it's a vault worthy of your most legendary rolls. Sporting a valiant d20 emblem embossed on its lid, your dice will feel the embrace of the gods of luck. With each roll, you'll almost hear the faint chorus of ancient bards singing your victory!Twist of Fate: Secure your precious math rocks with a twist! Our screw-top lid is engineered for those who like to keep fate tightly sealed until it’s time to let the critical hits fly. No more tragic spills or dice-related mishaps; just smooth threads and a satisfying closure that keeps your beloved dice snug and safe.Printable by Mortals: Fear not, fellow crafters! You need not be a grand wizard to conjure this box into reality. Designed for effortless printing, this model requires no mystical supports, ensuring a clean, hassle-free creation process even for novice spellcasters of the 3D-printing realm.A License to Forge: Not only do you get an incredible dice box, but with the included commercial license, you can print and sell these beauties to fellow enthusiasts! Spread the joy, pad your coin purse, and become the beloved merchant in your gaming community.Key Features:<ul><li>Holds a standard set of 7 polyhedral dice</li><li>d20 logo embossed on the lid for that extra flair</li><li>Screw-top design to keep your dice secure</li><li>Easy to print without the need for wizardly supports</li><li>Commercial license included so you can multiply your treasure</li></ul>So, are you ready to add some charisma to your dice-rolling experience? Click "Download" and let the fates decide your fortune (or just enjoy a really cool dice box). Roll with confidence, roll with style - roll with the Ultimate 3D-Printable Dice Box!

DiceCase with Screw Top Lid "COMMERCIAL USE ALLOWED"

Preischl 3D

Do you like my designs? I would be happy if you would support me by joining my Printables club! :) (already from 3$) It also gives you access to exclusive models ;) https://www.printables.com/@Preischl3D Or do you want a sales licence? Then you can book the commercial tier!&nbsp;All models I publish are tested by me and my community before I publish them.Here you get a texture roller to leave a pattern on different soft materials. We tested foam, clay and plaster, but the possibilities are endless.The roll is scaled to 60mm x 145mm with a 25mm hole in the middle.Settings for printing:Layer height: 0.2mm Outer perimeter: 4 Support: NO Infill: 20% Massive support: every 10mm Toplayer: 7 Botlayer: 6

Textured Roll With Hexagon Pattern

Kitchen

downsbdld

3 fun little Valentines day gnomes!&nbsp;Easy to recolor to your liking!

Valentines Day Gnomes - Set of 3

Valentine

Jan 3D

Bambu Lab Storage System&nbsp;UPDATE 24.11.2023Now with new LID for Full Hotends here is the LINK:<a target="_blank" href="https://makerworld.com/de/models/72681#profileId-77205" rel="nofollow noopener">https://makerworld.com/de/models/72681#profileId-77205</a>&nbsp;This is a newly developed storage system for all the Bambu Lab printers X1C / P1S, /P1PThe goal was to store all spare parts as well as the glue stick and the Allen key in one box. This was realized as space-saving as possible.&nbsp;The dimensions of the closed box are: 181mmx126mmx32mm&nbsp;The following parts can be accommodated: - Four hotends with all accessories (silicone sock, holders for the thermister as well as the corresponding screws). - Four nozzle wipers + mounting screws - Spare filament cutter - Nozzle cleaner - Glue stick from Bambu Lab - Allen wrench supplied - three times each Lubricant Grease and Thermal Grease&nbsp;The two parts are not joined together, the lid is just put on. &nbsp;Im happy to adapt my design if you want something changed, just contact me and we can work something out.&nbsp;Also look at may other Storage Box:<a target="_blank" href="https://makerworld.com/de/models/47503" rel="nofollow noopener">https://makerworld.com/de/models/47503</a>

Bambu Lab - Tools and Accessories Box

Accessories

Jasonuht

Have some fun with your friends or coworkers. Let them know that they beat the odds and became the person they are today with this silly little award.Printed at 200% of the original design.AMS for color swap with a total print time of 2h 37m.

Strongest Swimmer Award

Curiosities

twgondeck

Used to place small magnets with proper orientation. Hold slider down, attracts magnet, place in proper location, pull slider back, magnet is released. Can be used to place any size of small magnets.&nbsp;Recommended you print two to have one for each orientation. I included recesses in the top of the slider and cap to use a pen spring to hold the slider down, but it works fine without.&nbsp;Required:3x3mm cylinder magnetPen spring (optional)

Magnet Setter

Hobby & DIY

The Big Greek

Complete Rod Cleaner Z-Axis Version No.1 with Logo (simple and fast) Single Version&nbsp;★ New ★ Update from 29.12.2023 <a target="_blank" href="https://makerworld.com/de/models/112326#profileId-120249" rel="nofollow noopener">Automatic Z-Axis Lube Helper</a> ★ here is the link <a target="_blank" href="https://makerworld.com/de/models/112326#profileId-120249" rel="nofollow noopener">https://makerworld.com/de/models/112326#profileId-120249</a>&nbsp;★ New ★ Update from 21.12.2023 <a target="_blank" href="https://makerworld.com/de/models/102023#profileId-108654" rel="nofollow noopener">Rod Cleaner V2 Set + Lid + Toolcase Magnet Version</a> ★ here is the link <a target="_blank" href="https://makerworld.com/de/models/102023#profileId-108654" rel="nofollow noopener">https://makerworld.com/de/models/102023#profileId-108654</a>&nbsp;★ New ★ Update ★ <a target="_blank" href="https://makerworld.com/de/models/99424#profileId-105992" rel="nofollow noopener">Rod Cleaner Set + Tool Case</a> here is the link <a target="_blank" href="https://makerworld.com/de/models/99424#profileId-105992" rel="nofollow noopener">https://makerworld.com/de/models/99424#profileId-105992</a>&nbsp;<h3>★ Dont forget o clean your X-Axis ★ here is the link <a target="_blank" href="https://makerworld.com/de/models/89719#profileId-98171" rel="nofollow noopener">Carbon Rods Cleaner V2 X-Axis (simple and fast)</a> <a target="_blank" href="https://makerworld.com/de/models/89719#profileId-96043" rel="nofollow noopener">https://makerworld.com/de/models/89719#profileId-96043</a></h3>&nbsp;Based on the <a target="_blank" href="https://makerworld.com/de/models/89719#profileId-98171" rel="nofollow noopener">Carbon Rods Cleaner V2 X-Axis (simple and fast)</a> , I have now designed a Rod Cleaner for the Z-Axis. Again, it's Simple and short time to print.Of course, there is also a version that is a bit smoother but takes a little longer.&nbsp;LET'S GET STARTED!&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_2390fb036d154.gif"></figure><ol><li>Print</li></ol><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_ac8ecc42289ed.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_6d92973f821df.jpg"></figure>&nbsp;2. Take a sponge and cut 2 pieces to the size of 20mm x 30mm, just like with the <a target="_blank" href="https://makerworld.com/de/models/89719#profileId-98171" rel="nofollow noopener">Carbon Rods Cleaner V2 X-Axis (simple and fast)</a> , and press them into the designated openings. Now soak them with ISO<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_70401aa53f222.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_d9d9bf02ef0d1.jpg"></figure>&nbsp;3. Let's start the cleaning!&nbsp;Place the small box around the Z-Axis, hold it with your fingers, and press the desired direction on the display... the cleaning begins :-) Pay attention to the final distance of the Z-Axis Top and Bottom . Do not drive too far, as you could otherwise damage your printer.Cleaning the rear Z-Axis is also possible without disassembling the entire printer. For this, I recommend the Rod Cleaner Z-Axis Complete Version (what a name) here you dont need to hold it all the time, the tweezer makes it for you :-)<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_db6ad16220329.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_19af0e1d1c595.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_0242a76fe13eb.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_ac1d6cddb1a58.jpg"></figure>&nbsp;4. The tweezer for the box with the spacer is very convenient. If you use this combination, you have your fingers free and can easily clean your Z-Axis as shown in the pictures. Of course, it can also be used without a spacer.<img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_fe174a641f46e.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_572c04a99f2e4.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_f1835362a064a.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_9b348ba16ee12.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_05e1c1c9c2c7c.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_e3051c947c0df.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_0205ce3e2f2cf.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_45328085ad19.jpg">&nbsp;&nbsp;4. After you're done, it should look like this :-)<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_a85fb86992665.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/464529/2023-12-17_d100deacc503.jpg"></figure>&nbsp;5. After cleaning, you should grease the Z-AXIS again. The included grease in the accessories should be sufficient; if not, purchase new grease.&nbsp;easy to use, easy to clean&nbsp;Have fun building and cleaning!&nbsp;if you like my work/project consider supporting me with these options:<ul><li>leave a like</li><li>leave a comment</li><li>download the file</li><li><a target="_blank" href="https://www.buymeacoffee.com/thebiggreek" rel="nofollow noopener">or By me a Coffee</a></li></ul>I also appreciate comments a lot.

Complete Rod Cleaner Z-Axis Version No.1

DonMatis

Chronos the keeper of Time, created using HueforgeThis time did some changes to the colours but can also be printed using grayscale.As always, hope you like it and looking forward to see your makes :)Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used:<ul><li>PLA Overture Black</li><li>PLA PolyTerra Charcoal Black</li><li>PLA Overture Chocolate Matte</li><li>PLA Overture Chocolate</li><li>PLA Overture Brown</li><li>PLA PolyTerra Muted White</li><li>PLA Overture White</li></ul>Swap Instructions:<ul><li>Start with Black</li><li>At layer #6 (0.56mm) swap to Charcoal Black</li><li>At layer #8 (0.72mm) swap to Chocolate Matte</li><li>At layer #10 (0.88mm) swap to Chocolate</li><li>At layer #12 (1.04mm) swap to Brown</li><li>At layer #14 (1.2mm) swap to Muted White</li><li>At layer #20 (1.68mm) swap to White for the rest.</li></ul>

Chronos - Time Keeper

Hiko 3D

**These designs are for personal use only. If you want to get exclusive and free designs also become an official reseller visit my patreon and join!**&nbsp; Hello everyone, I share the a new Christmas-themed knitted container: Snowman. ☃️ - It is a simple container where you can store store some candies or anything else you want to give this Christmas. 🎁🍬&nbsp;- Does not need support. Santa is printed in 4 colors with 1 AMS unit. I hope you like it and can create Snowman in different colors with the other Christmas members. ☃️🎅🦌🐱🎄&nbsp;&nbsp;&nbsp;

AMS