jklauck

Josh-3D

Check out the other two games in the series<a target="_blank" href="https://makerworld.com/en/models/140755#profileId-153348" rel="nofollow noopener">Checkers</a><a target="_blank" href="https://makerworld.com/en/models/134530#profileId-145997" rel="nofollow noopener">Chess</a>&nbsp;[Update] After getting some feedback, I adjusted the print profile, so the color change isn&#39;t discharged into the infill. I also increased the bottom shell layers. Since the main color scheme of this is white/black/green, it makes sense to reinforce those settings to avoid color bleed. Also added an A1 Mini plate for the Mini users!&nbsp;[Update 2!] Shout out to <a target="_blank" href="https://makerworld.com/en/u/840057458" rel="nofollow noopener">Wcad00 </a>for the added clip![Update 3!] Shout out to <a target="_blank" href="https://makerworld.com/en/u/982974221" rel="nofollow noopener">SoftWareCrash </a>and <a target="_blank" href="https://makerworld.com/en/u/425227684" rel="nofollow noopener">Adminstrator</a> for their contributions. The “Pocket” version, a 50% scaled version, and for a set of Xs and Os, with the Xs cut to fit inside the Os.&nbsp;A Travel TicTacToe game, for those long spans stuck at sea, where you don&#39;t want to risk using a pencil on the side of your life raft! Or uh, you know, any other occasion too, like road trips down the coast with friends, or spending family time playing games!&nbsp;Player piece quantity is setup so that X goes first!&nbsp;The clearance is tight. The X and Os should fit fine, but if your printer is sloppy, it might be a tight fit.&nbsp;&nbsp;-------If you like my work, consider showing your love by <a target="_blank" href="https://www.buymeacoffee.com/josh3d" rel="nofollow noopener">Buying me a coffee</a>. Additionally, if you&#39;re looking to sell prints of my design, please check out my <a target="_blank" href="https://www.patreon.com/josh3d/" rel="nofollow noopener">Patreon</a> page for more information.&nbsp;&nbsp;

TicTacToe - Travel Edition

things my wife wants me to print

KobaRiley

<h2>Cable Tidy for Bambu X & P Series</h2>Got a bit tired of the messy setup on the back of the printer, and designed some cable supports that don't need screws or magnets.Also got a bit carried away and designed a few different versions.&nbsp;The PTFE tube on the right side, that goes to the printer, is free to move back and forth, but stays in the channel.The cables and tubes keep everything in place, but I've added some double sided tape on mine to keep it a bit tidier.<h3>Install</h3>To install the plate, you need to remove the two cables, and the left hand side PTFE tube. Then, remove the PTFE tube at the connector closest to the printer… feed that tube through the hole in the cable tidy plate, and then just reconnect everything.&nbsp;I've had this running on two printers for about 20 prints each, and have had no issues.&nbsp;There are different designs available, from 4, 3, 2 and 1 colour. The 1 colour basic version is by far the fastest to print… The Texas version is my favourite, and looks much better in reality than my awful photos….&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/601192/2024-01-16_432ca9585a8cb.jpg">&nbsp;&nbsp;The cables and tubes can still be removed with the standard little tools that are everywhere on Makerworld, but I've included a couple that fit slightly better with with this plate.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/601192/2024-01-16_6a6ab2a212209.png"></figure>&nbsp;This project took several days, and many many test prints. If you like the model, and feel like buying me a coffee, it would be greatly appreciated. <a target="_blank" href="https://ko-fi.com/kobariley" rel="nofollow noopener">https://ko-fi.com/kobariley</a>&nbsp;

things my wife wants me to print

Things I want to print