jenskoschnick

justfourprint

Geburtstagsschild&nbsp;Der Name und die Zahl können im Slicer geändert werden.&nbsp;Falls die Schrift auf der Druckplatte gedruckt werden soll, bitte erst den Namen und die Zahl ändern, danach mit dem “Drehen Werkzeug” um 180 Grad drehen. Nicht mit dem “Auf Fläche legen” Werkzeug!&nbsp;Farben können auch nach belieben geändert werden.&nbsp;Viel Spaß beim verschenken :)

Geburtstagsschild

dajana

Lucky3310

Hallo benutzen Sie einen kleinen Stab um den Bissanzeiger unter der Rolle zu positionieren anschließend einfach die Angelschnur einfädeln und die Bremse nicht ganz so stramm stellen sobald ein Biss kommt hebt sich der Bissanzeiger und rutscht danach nach unten man könnte ihn noch ausrüsten mit einer Glocke um es Hörbar zu machen ansonsten funktioniert das tadellos am Forellenteich

Bissanzeiger ( Forellenkletterer )

angeln

CopyKnight

With the introduction of the Air-Stream-Freezer, our team set itself the task of developing a model for the Bambulab X series. The biggest challenge was to make it LIDAR compatible. Our team rose to this challenge, further developed the Air-Stream-Freezer and quickly designed the Air-Stream-Turbine. Once again, I would like to thank the entire team, who have once again invested every spare minute for months in the development of the project. Once again, it has been designed, designed, changed and tested. A special thank you to Paul, to whom we tirelessly handed over new designs so that he could check compatibility. Once again, it is expressly stated that remixes of this product design are completely prohibited, as once again no phase or rounding off has been added more than necessary. To ensure that there is something for everyone&#39;s taste, this time there are of course two more versions available in addition to the 7 well-known ones: Firstly, the original: 1: Air-Stream-Turbine (it wasn&#39;t called that for no reason) <a target="_blank" href="https://makerworld.com/en/models/429489#profileId-333824" rel="nofollow noopener">https://makerworld.com/en/models/429489#profileId-333824</a> 2: Bambu Lab logo with lettering <a target="_blank" href="https://makerworld.com/en/models/429475#profileId-333807" rel="nofollow noopener">https://makerworld.com/en/models/429475#profileId-333807</a> 3: Bambu Lab lettering single <a target="_blank" href="https://makerworld.com/en/models/429500#profileId-333837" rel="nofollow noopener">https://makerworld.com/en/models/429500#profileId-333837</a>  4: Bambu Lab logo single <a target="_blank" href="https://makerworld.com/en/models/429494#profileId-333828" rel="nofollow noopener">https://makerworld.com/en/models/429494#profileId-333828</a> 5: Bambu Lab P1S version <a target="_blank" href="https://makerworld.com/en/models/429485#profileId-333817" rel="nofollow noopener">https://makerworld.com/en/models/429485#profileId-333817</a> 6: Bambu Lab P1P version <a target="_blank" href="https://makerworld.com/en/models/429480#profileId-333812" rel="nofollow noopener">https://makerworld.com/en/models/429480#profileId-333812</a> 7: completely without bells and whistles, branding or logo <a target="_blank" href="https://makerworld.com/en/models/429474#profileId-333806" rel="nofollow noopener">https://makerworld.com/en/models/429474#profileId-333806</a> Newly added: 8: Bambu Lab X1C version <a target="_blank" href="https://makerworld.com/en/models/429482#profileId-333814" rel="nofollow noopener">https://makerworld.com/en/models/429482#profileId-333814</a> 9: Bambu Lab X1E version <a target="_blank" href="https://makerworld.com/en/models/429486#profileId-333819" rel="nofollow noopener">https://makerworld.com/en/models/429486#profileId-333819</a> What&#39;s new in this version: The Air-Stream turbine can now be printed completely unsupported. There is a split inlet and an asymmetrical outlet for the air supply. Due to the asymmetrical outlet, it is only possible to speak of 360 degrees in relative terms, which is why we have omitted the degree sign in our illustration and replaced it with an asterisk. In case of doubt, this model can be printed with only two walls and completely without infill with a 0.2 layer height. However, we recommend 3 walls with 10% infill and a layer height of 0.1, or 4 walls and 10% infill with a 0.2 nozzle. For all variants, a corresponding number of upper layers should be ensured. This means 5 layers with 0.2 and 10 layers with 0.1 layer height. The magnets that must be used are the same size as those used in the original Bambu Lab component. (4x2 &amp; 2x2) For design reasons it was not possible to use larger magnets. At the point where the smaller magnet has to be placed, care must be taken when slicing that &#34;recognize thin walls&#34; is selected, as the wall thickness at this point is very small. However, this does not matter, the magnet can still be glued in cleanly without any problems and will hold. With a 0.2 Nozzle there is no problem at all, which is why the High Quality and Ultra pressure profile is specially designed for a 0.2 Nozzle.  It is generally known that the subject of component cooling is viewed with a great deal of skepticism and suspicion. Many people always want proof. But how and with what could you prove something if the evidence proves nothing, because it cannot prove anything, as it could just as well be manipulated? Then there are always many theoretical things that could possibly prove something, but theory and practice are worlds apart. That&#39;s why we won&#39;t try to convince anyone here. Everyone has to convince themselves. We simply want to invite everyone to do a little mini-experiment that they can understand for themselves. Place a glass filled with water under the original fan and everyone will be able to see the same result with their own eyes. The largest bulge in the water surface will not be in the middle under the nozzle, although this is where it would make the most sense in principle. The bulging of the water surface of the Air-Stream turbine, on the other hand, is much more centrally located under the nozzle. Again, these are facts that anyone can see for themselves if they are willing to carry out this simple test. Because let&#39;s not kid ourselves, pictures of a comparison of two 4-sided overhang tests do not seem to be credible enough, which is why we are sparing ourselves a direct comparison this time. Last but not least, it should be noted that the component should only be printed by someone who can dismantle the original and assemble the reprinted one without help. We will not provide any help in this regard, nor will we encourage anyone to possibly destroy the front housing assembly of the printer. Or to put it another way, you dismantle at your own risk. One last point should be mentioned. This model can also be printed without infill and completely without support. Neither the model nor one of the four printing profiles can be held responsible in the event that it should become detached from the build plate during printing. We decided to add a GIF of a print (High Quality and Ultra print profile) to prove that with a clean build plate and well calibrated ABS filament it is possible to print successfully without support and without brim. For anyone else who may have difficulties, a brim could be added. However, this should not be an argument for rating the model or print profile poorly.  What is the difference between the print profiles? Fast Print: Nozzle 0.4 - layer height 0.2 - first layer 0.2 - walls 2 - infill 0 % Medium: Nozzle 0.4 - layer height 0.1 - first layer 0.2 - walls 3 - infill 10 % Gyroid High Quality: Nozzle 0.2 - layer height 0.1 - first layer 0.2 - walls 4 - infill 0 % Ultra: Nozzle 0.2 - layer height 0.1 - first layer 0.2 - walls 4 - infill 10 % Gyroid Thank you and have fun.        Mit der Einführung des Air-Stream-Freezer hat sich unser Team es zur Aufgabe gemacht, ein Modell für die Bambulab X-Serie zu entwickeln. Die größte Herausforderung dabei war es, diesen LIDAR kompatibel zu designen. Dieser Herausforderung hat sich unser Team gestellt, den Air-Stream-Freezer weiterentwickelt und kurzer Hand die Air-Stream-Turbine konzipiert.  Auch heute möchte ich mich abermals bei dem gesamten Team bedanken, das abermals wieder jede freie Minute seit Monaten in die Entwicklung des Projektes investiert hat. Es wurde wieder erneut entworfen, designed, geändert und getestet. An Paul gibt es ein besonderes Dankeschön, den wir unermüdlich neue Entwürfe übergaben, damit er die Kompatibilität überprüfen konnte.  Einmal mehr wird hiermit noch einmal Ausdrücklich erklärt, das Remixe von diesem Produktdesign vollständig untersagt sind, da auch hier wieder keine Phase oder Abrundung mehr als nötig hinein konstruiert wurde. Damit auch diesmal wieder etwas für jedermanns Geschmack dabei ist, stehen diesmal zu den 7 altbekannten natürlich zwei weitere Versionen zu Verfügung:  Zum einen das Original:  1: Air-Stream-Turbine (der wurde nicht ohne Grund so genannt) <a target="_blank" href="https://makerworld.com/en/models/429489#profileId-333824" rel="nofollow noopener">https://makerworld.com/en/models/429489#profileId-333824</a>2: Bambu Lab Logo mit Schriftzug <a target="_blank" href="https://makerworld.com/en/models/429475#profileId-333807" rel="nofollow noopener">https://makerworld.com/en/models/429475#profileId-333807</a>3: Bambu Lab Schriftzug einzeln <a target="_blank" href="https://makerworld.com/en/models/429500#profileId-333837" rel="nofollow noopener">https://makerworld.com/en/models/429500#profileId-333837</a>4: Bambu Lab Logo einzeln <a target="_blank" href="https://makerworld.com/en/models/429494#profileId-333828" rel="nofollow noopener">https://makerworld.com/en/models/429494#profileId-333828</a>5: Bambu Lab P1S Version <a target="_blank" href="https://makerworld.com/en/models/429485#profileId-333817" rel="nofollow noopener">https://makerworld.com/en/models/429485#profileId-333817</a>6: Bambu Lab P1P Version <a target="_blank" href="https://makerworld.com/en/models/429480#profileId-333812" rel="nofollow noopener">https://makerworld.com/en/models/429480#profileId-333812</a>7: komplett ohne Schnickschnack, Branding oder Logo <a target="_blank" href="https://makerworld.com/en/models/429474#profileId-333806" rel="nofollow noopener">https://makerworld.com/en/models/429474#profileId-333806</a>  Neu dazugekommen ist:  8: Bambu Lab X1C Version <a target="_blank" href="https://makerworld.com/en/models/429482#profileId-333814" rel="nofollow noopener">https://makerworld.com/en/models/429482#profileId-333814</a>9: Bambu Lab X1E Version <a target="_blank" href="https://makerworld.com/en/models/429486#profileId-333819" rel="nofollow noopener">https://makerworld.com/en/models/429486#profileId-333819</a>  Was ist neu an dieser Version:  Die Air-Stream-Turbine kann nun komplett ohne Unterstützung gedruckt werden. Es gibt einen geteilten Einlass und einen asymmetrischen Auslass für die Luftzufuhr. Durch den asymmetrischen Auslass kann nur relativ von 360 Grad gesprochen werden, weshalb wir anstelle des Grad Zeichens in unserer Abbildung abgesehen und dies mit einem Sternchen ersetzt haben.Dieses Modell kann im Zweifelsfall mit nur zwei Wänden und komplett ohne Füllung mit einer 0.2 Schichthöhe gedruckt werden. Empfohlen wird allerdings 3 Wände mit 10% Füllung und einer Schichthöhe von 0.1, bzw. mit einer 0.2 Düse 4 Wände und 10% Füllung. Bei allen Varianten sollte auf entsprechend viel obere Schichten geachtet werden. Das heißt 5 Schichten bei 0.2 und 10 Schichten bei 0.1 Schichthöhe. Die Magneten die benutzt werden müssen, haben die selbe Größe wie die, die beim Original Bauteil von Bambu Lab verwendet wurden. (4x2 &amp; 2x2) Konstruktionstechnisch war es nicht anderes möglich größere zu verwenden. An der Stelle wo der kleiner Magnet platziert werden muss, muss beim Slicen darauf geachtet werden, dass „dünne Wände erkennen“ ausgewählt wird, da die Wandstärke an dieser Stelle sehr gering ist. Dies macht aber nichts, der Magnet kann trotzdem ohne Probleme sauber darin eingeklebt werden und wird halten. Mit einer 0.2 Nozzle gibt es dahingehend überhaupt keine Problem, weshalb das High Quality und Ultra Druckprofil speziell für eine 0.2 Nozzle ausgelegt ist.  Im allgemeinen ist bekannt, dass das Thema Bauteilkühlung mit viel Skepsis und Argwohn beäugt wird. Viele wollen immer Beweise. Aber wie und womit könnte man denn etwas beweisen, wenn die Beweise nichts beweisen, weil sie nichts beweisen können, da sie ebenso gut manipuliert sein können? Dann gibt es immer viele theoretische Dinge die womöglich etwas beweisen können, doch zwischen Theorie und Praxis liegen bekanntlich ja auch Welten. Deswegen werden wir hier auch nicht versuchen irgendjemanden zu überzeugen. Überzeugen muss sich schon jeder selbst. Wir wollen lediglich jeden einladen ein kleines für jeden selbst nachvollziehbares Miniexperiment zu machen. Stellt ein Glas mit Wasser gefüllt unter den Originallüfter und jeder wird dasselbe Ergebnis mit seinen eignen Augen wahrnehmen können. Die größte Ausbeulung der Wasseroberfläche wird nicht mittig unter der Nozzle sein, wo es prinzipiell allerdings am sinnvollsten wäre. Die Ausbeulung der Wasseroberfläche der Air-Stream-Turbine hingegen ist wesentlich mittiger und zentraler unter der Nozzle wiederzufinden. Das sind wiederum Tatsachen von denen sich jeder selbst überzeugen kann, sofern er gewillt ist, diesen einfachen Test zu machen. Denn machen wir uns nichts vor, Bilder von einem Vergleich zweier 4 Seiten-Überhangtests scheinen, so wir wir feststellten, nicht glaubwürdig genug zu sein, weshalb wir uns diesmal einen direkten Vergleich ersparen.  Zu guter Letzt sei noch darauf hingewiesen, dass das Bauteil nur jemand drucken sollte, der auch ohne Hilfe, den Originalen demontieren und den neu Gedruckten montieren kann. Es wird von uns dahin gehend keinerlei Hilfe geben, noch werden wir jemanden dazu zu animieren, womöglich die vordere Gehäusebaugruppe des Druckers zu zerstören. Oder nochmal anders ausgedrückt, sie demontieren auf eigene Gefahr. Ein allerletzter Punkt sei noch erwähnt. Dieses Modell kann auch ohne Infill und komplett ohne Unterstützung gedruckt werden. Weder das Modell noch eins der vier Druckprofile kann etwas dafür, für den Fall dass es sich während des Druckes von der Bauplatte womöglich lösen sollte. Wir haben uns entschieden extra eine GIF von einem Druck (High Quality und Ultra Druckprofil) hinzuzufügen, um zu belegen, dass es mit einer sauberen Bauplatte und gut kalibrierten ABS Filament problemlos möglich ist ohne Unterstützung und ohne Brim erfolgreich zu drucken. Für alle anderen, die womöglich Schwierigkeiten bekommen sollten, könnten ein Brim hinzufügen. Allerdings sollte dies keine Argument dafür sein, das Modell oder Druckprofil schlecht zu bewerten.  Worin unterscheiden sich die Druckprofile?  Fast Print: Düse 0.4 – Schichthöhe 0.2 – erste Schicht 0.2 – Wände 2 – Füllung 0 %Medium: Düse 0.4 – Schichthöhe 0.1 – erste Schicht 0.2 – Wände 3 – Füllung 10 % GyroidHigh Quality: Düse 0.2 – Schichthöhe 0.1 – erste Schicht 0.2 – Wände 4 – Füllung 0 %Ultra: Düse 0.2 – Schichthöhe 0.1 – erste Schicht 0.2 – Wände 4 – Füllung 10 % Gyroid  Danke und viel Spaß.

Fan Flow 360 Toroidal Air Duct X1C 风扇 气流 风扇流量 风道

muss tool

Biviyt

<h2>WORK IN PROGRESS</h2>  I have created a turbine with a gearbox, which is currently a work in progress. I printed it myself, and it functions, but the tolerances are not good. I plan on improving them shortly. Furthermore, I will be including instructions and a list of materials soon.  Print the parts on the second plate using PA6 or a material that can withstand high temperatures. Motor measurements: <img src="https://makerworld.bblmw.com/makerworld/draft/613358/2024-03-01_661a48a07c569.png" alt="">

Turbine with gearbox

garten 

Magic Studio 3D

ANIMAL KEYCHAIN For your cat or dog I recommend printing in two colors

Dog or Cat Keychain

N3KX

Hello. This is remix of adjustable phone holder. It can be inserted in VW brand phone holder that was integrated in VW car. &nbsp;<h3>Printing:</h3>Material: Recomended to use some heat resistance material if you gonna use it in summer.&nbsp;Support: It use little support that is easy to remove so please use my printing profile it is set.

VW Phone holder

Auto 

Regarnogal

a simple four leaf clover as gift for friends and family, as decoration for the new year celebration party or a simple giveaway&nbsp;i have added 2 types of print profiles<ul><li>one with 9 cloverleafs</li><li>one with a single cloverleaf</li></ul>both with ironing to have a smooth finish, without you can safe few minutes of printing.

four-leaf clover giveaway or decoration

Auftrag 

user_2640675396

<h4>simple soldering iron stand fit most soldering irons and a fast print </h4>

simple soldering station

löten 

TheMiguelBi

<h2>Coin sorter Printable</h2>Two version available:<ul><li>Bicolor (AMS)</li><li>Monocolor</li></ul>&nbsp;For assembling:<figure class="media"><div data-oembed-url="https://youtu.be/20TFDzHse_4"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/20TFDzHse_4" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

Coin Sorter - Euro edition !

lockcard

Rott3D

Maggot / worm fishing mold for rubber bait

Fishing Lure / Bait maggot/worm mold

Angeln 

Mysstra hueforge

Goku Truibuto a Akira Toriyama creado por IA y usando Hueforge para su impresion en 3D&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used: PLA Jayo Negro Transmission Distance: 0.3 PLA BambuLab Basic Jade White Transmission Distance: 6 PLA Jayo Negro Transmission Distance: 0.3 PLA BambuLab Basic Orange Transmission Distance: 5 PLA BambuLab Basic Yellow Transmission Distance: 6Swap Instructions: Start with Negro At layer #7 (0.64mm) swap to Jade White At layer #15 (1.28mm) swap to Negro At layer #18 (1.52mm) swap to Orange At layer #22 (1.84mm) swap to Yellow for the rest.

Goku tribute  Akira Toriyama Hueforge

Arbeitskollege 

Rabauke1986

Groot with Heart und Pupils

love 

humebeam

Hydra PRO - Advanced Bambu Lab AMS

miqu

The HiveLight is an innovative lighting fixture designed to immerse your space in mesmerizing colors and dynamic patterns. With its blend of captivating visuals, touch-sensitive controls, and audio-reactive lighting, the HiveLight adds an enchanting ambiance to any environment. While this tutorial provides detailed instructions for assembly and configuration, it's essential to approach this project with caution and understanding.&nbsp;Recreate at Your Own Risk:Building electronic devices involves working with various components and soldering, which can pose risks if not done correctly. Therefore, it's crucial to have a basic understanding of electronics and soldering techniques before attempting this project. If you're unfamiliar with these concepts, consider seeking guidance from someone with experience or conducting thorough research beforehand.&nbsp;Know What You're Doing:Each step in this tutorial requires careful attention to detail, from soldering connections to configuring software settings. Before proceeding, take the time to understand the purpose and implications of each action. If you encounter any uncertainties or difficulties along the way, don't hesitate to seek clarification or assistance.&nbsp;By acknowledging these considerations and approaching the project with care and knowledge, you can maximize your chances of success while minimizing potential risks. Enjoy the process of creating your HiveLight, but always prioritize safety and understanding throughout the journey.&nbsp;Materials Needed:<ul><li>ESP32 Development Board</li><li>WS2812B LED Strip</li><li>TTP223 Capacitive Touch Sensor</li><li>INMP441 MEMS Microphone</li><li>470 Ohm Resistor</li><li>USB Cable</li><li>1000 µF, 10V Capacitor</li><li>Jumper Wires</li><li>Soldering Iron and Solder</li><li>3D Printed Lamp Components</li></ul>Software Installation:&nbsp;Install WLED on ESP32:<ul><li>Connect the ESP32 to your PC via USB.</li><li>Visit <a target="_blank" href="https://install.wled.me/" rel="nofollow noopener">https://install.wled.me/</a> and follow the on-screen instructions to install the "AudioReactive" version of WLED.</li><li>Set up Wi-Fi credentials as prompted during the installation process.</li></ul>Visual representation how I soldered everything together:<img src="https://makerworld.bblmw.com/makerworld/draft/736376/2024-01-31_a9b70e461c1bd.png">&nbsp; Hardware Assembly:&nbsp;Prepare USB Cable:<ul><li>Cut one end of the USB cable and pass it through the hole in the 3D printed bottom part of the lamp.</li></ul>Solder Capacitor:<ul><li>Solder the 1000 µF capacitor across the USB cable's +5V and GND wires for power smoothing. Connect ESP32:</li><li>Solder a jumper wire from the positive leg of the capacitor to the 5V pin of the ESP32.</li><li>Solder another jumper wire from the negative leg of the capacitor to the GND pin of the ESP32.</li><li>Desolder the onboard LED from the ESP32 to prevent unwanted light emission through the lamp.</li></ul>Connect LED Strip:<ul><li>Solder a 470 Ohm resistor to GPIO16 on the ESP32.</li><li>Wrapped the LED strip around the tower and cut the excess strip. Counted how many LEDS I used - 33.</li><li>From the resistor, solder a jumper wire to the data input pin of the LED strip.</li><li>Solder the LED strip's +5V wire to the positive leg of the capacitor and the GND wire to the negative leg of the capacitor.</li></ul>Connect Microphone:<ul><li>Solder a wire from microphone's GND and L/R pins to the ESP32's GND pin.</li><li>Solder a wire from the microphone's VDD pin to the ESP32's 3.3V pin.</li><li>Solder a wire from the microphone's SD pin to GPIO32, SCK pin to GPIO33, and WS pin to GPIO25 on the ESP32.</li></ul>Connect Touch Sensor:<ul><li>Bridge the 'B' connection on the touch sensor.</li><li>Desolder the onboard LED</li><li>Solder a wire from the touch sensor's GND terminal to the capacitor's GND.</li><li>Solder another wire from the touch sensor's VCC terminal to the capacitor.</li><li>Solder a wire from the TTP223 sensor's I/O terminal to GPIO12 on the ESP32.</li></ul>After soldering, secure the ESP32 to the bottom case with hot glue, ensuring it's firmly attached. Place the touch sensor in its designated slot and apply hot glue around its edges. Let the microphone hang freely inside the case. Allow the hot glue to cool and harden before handling the assembly.&nbsp;Software Configuration:&nbsp;Configure WLED LED Preferences:<ul><li>Access WLED's web interface using the ESP32's IP address.</li><li>Navigate to the "Config" tab and select “LED Preferences.”</li><li>Tick the checkbox for "Enable automatic brightness limiter" and set "Maximum Current" to 400mA.</li><li>Choose "5V efficient (35mA)" under "LED voltage" and set the "Length" to how many LEDs you used under "LED outputs." In my case it was 33.</li><li>Assign GPIO 16 for LED data output and GPIO 12 for the touch sensor.</li><li>Click on the "Save" button to apply the LED preferences.</li></ul><img src="https://makerworld.bblmw.com/makerworld/draft/736376/2024-01-31_f71f7764ed6aa.png">&nbsp;Configure Audio Reactive Mode:<ul><li>In the WLED web interface, navigate to the “Config” tab again, then select “Usermods”.</li><li>Under "Digitalmic," set the "Type" to “Generic I2S”.</li><li>Assign pins for I2S communication: Pin I2S SD: 32, Pin I2S WS: 25, Pin I2S SCK: 33</li><li>Set "Pin I2S MCLK" to “Unused.”</li><li>Click on the "Save" button to apply the usermod configuration.</li></ul> <img src="https://makerworld.bblmw.com/makerworld/draft/736376/2024-01-31_5a2fbf6a6cb6e.png">&nbsp;Testing and Usage:&nbsp;Test Touch Sensor Functionality:<ul><li>Verify that the touch sensor can toggle the lamp on and off effectively. </li></ul>Test Audio-Reactive Functionality:<ul><li>In the WLED web interface, select an audio-reactive preset.</li><li>Play music or generate noise near the microphone to observe the lamp's dynamic audio-reactive lighting patterns.</li></ul>Adjust Settings and Presets:<ul><li>Customize settings and presets in the WLED web interface to fine-tune the mood lighting experience. </li></ul>Follow these instructions carefully to assemble and configure your HiveLight Mood Lamp. Enjoy the mesmerizing light displays and interactive features!

WLED HiveLight audioreactive mood lamp

wled 

demek3d

<figure class="image image-style-align-center image_resized" style="width:42.53%;"><img src="https://makerworld.bblmw.com/makerworld/draft/103466/2023-10-19_eo67f7e7awyy.gif"></figure>This can be printed as two separate prints. You need to enable z-hop (0,6mm is enough). You can enable z-hop only for first several layers (in Super slicer at least). First you print hexagons and on top of that main body. If you z homing in the middle off the bed you need to move it in slicer a little to make space for your probe. Dont forget to disable mesh leveling for second print. Disable skirt or brim on first print. Remove purge line after first print is done. Its designed for 0,2mm layer height.or<div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=svmrOFKqS6c"><iframe src="https://www.youtube.com/embed/svmrOFKqS6c" frameborder="0" allowfullscreen=""></iframe></div>or Just use IDEX printer. Or other multi material solution.Both files are proper oriented for printing. For alingment you need to move hexagons +1,2mm on Y in slicer and do some minor alingments.Inspiration:<a href="https://www.printables.com/en/model/225153-voron-stealthburner-face" rel="nofollow">https://www.printables.com/en/model/225153-voron-stealthburner-face</a>22.10.22 New files with more clearance.24.01.23 Added SB main body without gaps (chamfers)12.03.2023 Added remix of Panzerkatten 3DO cam grille SB body<a href="https://github.com/3DO-EU/nozzle-camera/tree/main/printers/Voron_Stealthburner" rel="nofollow">https://github.com/3DO-EU/nozzle-camera/tree/main/printers/Voron_Stealthburner</a>

Hexagonal Stealthburner

voron 

gridfinity

Corona

omfgitsjimmy

This is the popular Spool winder from Printables but this has all the plates set up with the improved parts, reinforced gears and additionally, full coloring of the gear sets. This is set up to be run from an electric motor.

Full Color Filament winder with all upgraded pieces for X1C

test

BENOengineering

Protect your beer with this can cover against wasps, bugs and other co-drinking persons :)The bottom snaps onto the top of a 0,5L - 0,33L (short) - 0,33L (long) can. If you want it to work with a 0,25L can, scale both parts to 0.96.Easiest way to assemble is by gently squeezing together the circle of the bottom part and slide the top into the hinge-part.&nbsp;Check out the alphabet-version as well:<a target="_blank" href="https://makerworld.com/en/models/458456" rel="nofollow noopener">https://makerworld.com/en/models/458456</a>&nbsp;Commercial license you can get here:https://buymeacoffee.com/benoengineering/e/265720

Beer protector

Beer 

Icehorn

A dispenser for Nespresso Vertuo style capsules.&nbsp;Prints with minimal supports and can be attached easily to a wall via double sided tape or similar.

Nespresso Vertuo Coffee Dispenser

Kaffee 

Stag 3D

<h3>How to play:</h3><ol><li>Setup the base on a flat surface and place the Tetra Balance block onto it.</li><li>Take it in turns with your opponent to place the blocks onto the Tetra Balance piece. You can place the blocks with one hand only and once you have chosen a bloke you cannot change it.</li><li>Repeat until the tower eventually falls. </li><li>If you cause the tower to fall your opponent wins. </li></ol>&nbsp;

Tetra Balance Game

lern Spielzeug 

Jerryie

My completely redrawn improved bearings. They were inspired by guppik from Thingiverse. They have improvements for easier printing and a new body structure.&nbsp;&nbsp;<ul><li>If you are experiencing difficulty with bearing rotation, don&#39;t worry it should loosen up and become much smoother over time, or add some lube.</li></ul><figure class="image image_resized" style="width:40.56%;"><img src="https://media.printables.com/media/prints/542689/rich_content/b39484bc-5c26-4ce3-aa6d-02d60a3f8ac5/thumbs/cover/800x437/png/image.webp"></figure><ul><li>For best results, ensure the bed is not too close to the nozzle!</li></ul>A version of these dimensions:<figure class="image image-style-side image_resized" style="width:76.47%;"><img src="https://makerworld.bblmw.com/makerworld/draft/788495/2023-10-09_d4652358a50ed.webp"></figure>8 x 22 x 7 mm - 608 6 x 19 x 6 mm - 629 9 x 17 x 5 mm - 6897 x 14 x 5 mm- 6875 x 16 x 5 mm - 6255 x 11 x 5 mm - 68510 x 15 x 4mm - 6700

Print in place small bearings

3d drucker Ideen 

Indibles

Erotic - vagina cookie cutter / stamp

Erotic - vagina cookie cutter / stamp

sexy

FelixTheWhale

This pack includes the following bearings on different plates: <ul><li>608ZZ</li><li>607ZZ</li><li>606ZZ</li></ul>While these bearings lack the strength and durability of metal bearings, but good for functional prototyping. Their design has been improved over previous version to reduce brittleness, with minimized gaps for better stability and performance. &nbsp;Printed with OEM 0.4mm nozzle with PLA. I am almost sure 0.6 nozzle is too thick for this - balls will likely stick to outer and inner race.&nbsp;Each model is designed with a 0.12 mm layer thickness and a peel-away sacrificial bottom layer (marked by a red arrow) to support the balls during printing, which shall be removed using a thin flat screwdriver/pin/fingernail etc.<figure class="image image_resized" style="width:36.82%;"><img src="https://makerworld.bblmw.com/makerworld/draft/274494/2023-12-16_69fe2a8c732278.png"></figure>Post print: I recommend to cycle the bearings through back and forth multiple times with moderate force to smooth out surface imperfections and disconnect balls that may have accidentally adhered.. Then apply silicon grease.

Ball Bearings 608ZZ, 607ZZ, 606ZZ / Pack of 3 bearings

technisch 

Pocketcar_PT

This is a light box, in which I printed the white base without solid top filling so that the honeycomb infill was visible and gave this effect you see in the photos, you can try other patterns and infill.&nbsp;You can leave ideas for me to do more things like this, thank you all, please let me know if you have any questions!

Car Service light box

Lampen 

Ruvim KUB

<img src="https://makerworld.bblmw.com/makerworld/draft/500500/2024-02-04_7ff2b68f88cd1.jpg">Excited to introduce the third version of the toothpaste stand.To download the new version follow the link on the project page  <a target="_blank" href="https://makerworld.com/en/models/171580#profileId-188370" rel="nofollow noopener">Stand for Toothpaste V3.0 </a>&nbsp;&nbsp;&nbsp;&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/500500/2023-12-17_6bbea4293d884.jpg"></figure>ENG:A very handy stand for toothpaste, hand cream and many products that are stored in tubes. This is the second version and this time I simplified the model so that you can print everything in one print. Nothing else needs to be glued, twisted or assembled. My practice showed that such a simple model works even better than the previous one. I think you can print such things for your girlfriend or wife and thus show that your 3D printer does not stand between you and it helps to strengthen your relationship :D&nbsp;RU: Очень удобная подставка для зубной пасти, крема для рук и многих средств которые хранятся в тюбиках. Это уже вторая версия и в этот раз я упростил модель так, чтобы можно было все напечатать за одну печать. Больше не нужно ничего склеивать, скручивать и собирать. Моя практика показала что такая простая модель работает даже лучше чем предыдущая. Думаю такую вещи можно распечатать для своей девушки, жены тем самым показать что ваш 3Д принтер не стоит между вами, а наоборот помогает укрепить отношения :D&nbsp;ENG:It turns out that a lot of people don't know how to properly tuck toothpaste into a toothpaste holder. Here are some photos that clearly show it.&nbsp;RU:Оказывается что много людей не знают как правильно заправлять зубную пасту в подставку. Вот несколько фотографий которые наглядно это показывают.&nbsp;And also I would like to tell you that I recently started a small store on <a target="_blank" href="https://www.etsy.com/shop/3dkub" rel="nofollow noopener">Etsy.com</a> here will appear instrementy and exclusive projects that will not be in the open access.<img src="https://makerworld.bblmw.com/makerworld/draft/500500/2023-12-23_583fbf17b81bd.jpeg"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/500500/2023-12-23_529db265e8bc7.jpeg"></figure><h2>My some other things:</h2><figure class="image"><a href="https://3d.ruvim.info/thingiverse" target="_blank" rel="nofollow noopener"><img src="https://3d.ruvim.info/thing.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/151492#profileId-165387" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/500500/2024-01-21_140ed1f4e28fc.jpg"></a><a target="_blank" href="https://makerworld.com/en/models/149624#profileId-163286" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/500500/2024-01-21_c9f371a901922.jpg"></a><a target="_blank" href="https://makerworld.com/en/models/135080#profileId-146564" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/500500/2024-01-11_f09984058f1de.jpg"></a><img src="https://3d.ruvim.info/0450.png"><a target="_blank" href="https://www.thingiverse.com/thing:4968267" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Auto-Solder-Feeder-V1.1.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4934874" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Magnetic-mount-for-Street-style-Clocks.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/133763#profileId-145135" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Rectangular-stand-for-cotton-buds-and-disks.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4872540" rel="nofollow noopener"><img src="http://things.ruvim.info/img/phone-clip.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4860781" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Anex-sport-Min.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/97564#profileId-104137" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Stand-for-toothpaste-V2.0.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/105242#profileId-112325" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Stand-for-cotton-swabsticks-and-discs-V5.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4751509" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Smart-faucet-on-Arduino-(filter-resource-counter).jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/133785#profileId-145164" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Organizer-for-3D-printer.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4709801" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Acetone-Bath-on-Magnets.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4689514" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Case-for-rfid-tags.jpg"></a> <a href="Nozzle-Box.jpg" rel="nofollow"><img src="http://things.ruvim.info/img/Nozzle-Box.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/127746#profileId-138242" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Table-Adjustment-Knob-M3.jpg" alt="Table Adjustment Knob M3"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4539243" rel="nofollow noopener"><img src="http://things.ruvim.info/img/PCB-Etching-Tray.jpg" alt="PCB Etching Tray"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4495533" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Speed-Controller-220V.jpg" alt="Speed Controller 220V"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4458304" rel="nofollow noopener"><img src="http://things.ruvim.info/img/M%D0%BEdular-Mini-Circular.jpg" alt="Mоdular Mini Circular"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4383145" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Clock,-Counter-Subscribers..jpg" alt="Clock, Counter Subscribers."></a> <a target="_blank" href="https://www.thingiverse.com/thing:4361811" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Compass---Plotter.jpg" alt="Compass - Plotter"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4356203" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Phone-Clip..jpg" alt="Phone Clip."></a> <a target="_blank" href="https://www.thingiverse.com/thing:4327360" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Phone-Stand.jpg" alt="Phone Stand"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4317738" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Mini-Grinder.jpg" alt="Mini Grinder"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4304240" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Disc-Sander-Duo.-D50mm,-D75mm.jpg" alt="Disc Sander Duo. D50mm, D75mm"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4265679" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Lifting-Gear-For-Automatic-Nozzle-Cleaner.jpg" alt="Lifting Gear For Automatic Nozzle Cleaner"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4216312" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Mini-electric-lighter.jpg" alt="Mini electric lighter"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4212059" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Stand-for-toothpaste.jpg" alt="Stand for toothpaste"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4123230" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Camera-Weight-for-Diving.jpg" alt="Camera Weight for Diving"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4099456" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Electric-lighter.jpg" alt="Electric lighter"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4086763" rel="nofollow noopener"><img src="http://things.ruvim.info/img/The-best-soldering-iron-stand.jpg" alt="The best soldering iron stand"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4056390" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Flux-stand.jpg" alt="Flux stand"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4084435" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Mobile-Hard-Drive:-2.5-Inch-USB-3.0-SATA.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/118219#profileId-127104" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Magnetic-plate-for-little-things.jpg" alt="Magnetic plate for little things"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3970160" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Clamp-for-firmware-controllers-6-pins.jpg" alt="Clamp for firmware controllers 6 pins"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3976187" rel="nofollow noopener"><img src="http://things.ruvim.info/img/2-relays-box-or-ESP-01-with-relay.jpg" alt="2 relays box or ESP-01 with relay"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3970750" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Case-for-Ndemcu.jpg" alt="Case for Ndemcu"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3942946" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-A-B-C-D-E.jpg" alt="Alphabet for children. A B C D E"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3946878" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-F-G-H-I-J.jpg" alt="Alphabet for children. F G H I J"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3974764" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-K-L-M-N-O.jpg" alt="Alphabet for children. K L M N O"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3989549" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-P-Q-R-S-T.jpg" alt="Alphabet for children. P Q R S T"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3991721" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-U-V-W-X-Y-Z.jpg" alt="Alphabet for children. U V W X Y Z "></a> <a target="_blank" href="https://www.thingiverse.com/thing:3912631" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Replacement-SD-Card-Case.jpg" alt="Replacement SD Card Case"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3914719" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Solder-feeder.jpg" alt="Solder feeder"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3851649" rel="nofollow noopener"><img src="http://things.ruvim.info/img/USBasb-case.jpg" alt="USBasb case"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3845727" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Magnet-stick.jpg" alt="Magnet stick"></a>&nbsp;&nbsp;&nbsp;

Stand for toothpaste 

haushalt

andythilo

Honeycomb front drawer set for the BLV AMS Riser.&nbsp;Also available are my honeycomb drawer knobs - https://makerworld.com/en/models/96831#profileId-103295

BLV AMS Honeycomb Drawer Set

ams 

The Big Greek

Wiper Upgrade Adapter Simple&nbsp;After asking myself so often why the nozzle doesn't get really clean, I set to work and designed a small but excellent UPGRADE.&nbsp;It is simple and easy, installed within 5 minutes and works perfectly. It fits perfectly into the poop container and does not interfere with the ejection.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/524337/2023-12-15_e7a509335f159.jpg"></figure>&nbsp;You only need the small adapter, <a target="_blank" href="https://www.amazon.de/Scheibenb%C3%BCrste-Drahtb%C3%BCrsten-Messingb%C3%BCrsten-Drehwerkzeug-Rotationswerkzeuge/dp/B095PJJZLF/ref=sr_1_10?__mk_de_DE=%C3%85M%C3%85%C5%BD%C3%95%C3%91&crid=HJ42NFZ0ABWM&keywords=vape+brush&qid=1702670817&sprefix=vape+brush%2Caps%2C79&sr=8-10" rel="nofollow noopener">a small brush find it here link</a> (Brush 3mm) (possibly you find the same in your country) , the rest is original accessories.&nbsp;I shortened the brush handle to 5mm , you can also make it shorter or leave it as long as you like&nbsp;The installation is very easy, as you can see in the pictures. I have added a small support (probably more for the eye and the conscience).&nbsp;I printed the whole thing in PLA. Now have fun building it.&nbsp;1. remove the original wiper&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/524337/2023-12-15_3a8ea4ad2fd99.jpg"></figure>2. fix the original screw a little so that screwing it in is easier&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/524337/2023-12-15_b2565c6d94e05.jpg"></figure>3. screw everything together&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/524337/2023-12-15_fb1854ccaad77.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/524337/2023-12-15_a53f7e7ac0992.jpg"></figure>4. take another screw from the supplied accessories and screw it on a little so that you don't lose the screw in the poop container.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/524337/2023-12-15_72331374d53f5.jpg"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/524337/2023-12-15_d49052b93bd0d.jpg"></figure>5. install everything, insert the brush and off you go.In my case, the brush was a little loose, so I glued it in place. Then I fanned out the brush head and lo and behold...PERFECT!&nbsp;if there are any leftovers after the print, just pull it out&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/524337/2023-12-15_bf6c5b5bac111.jpg"></figure>&nbsp;&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/524337/2023-12-15_4e86b622ab2b5.gif"></figure>&nbsp;&nbsp;&nbsp;Easy to use, easy to clean&nbsp;If you like it, rate it, share it. THX&nbsp;Have FUN&nbsp;&nbsp;

Nozzle Wiper Upgrade Adapter Simple

nächste Projekt 

Maoirae

Due to hotend design there is problem, that hotend fan is taking air to cool down from bad places where is hot air, like bellow from around heatblok and heatbed and that can lead to melt filament too soon before heatblok and cause clog. So to prevent this heat creep I designed a little fan duct to prevent that. Its made to take air directly from the side of hotend housing. Its made simply to just screw directly to part cooling fan, than you can assemble front hotend housing as normal. Hope it will help you.&nbsp;Print from PETG or ABS for better heat resistance.&nbsp;There is also model for X1C/X1 in my published models: <a target="_blank" href="https://makerworld.com/de/models/98684#profileId-105217" rel="nofollow noopener">https://makerworld.com/de/models/98684#profileId-105217</a>

Hotend fan duct P1P/P1S

Bambu umarbeiten 

Blacho

Hand statue that will hold the standard sized bic lighter

Shocker Desk Statue - Holds Standard Bic

Büro 

Libb_s

Headset stand

PS11-Print

Ich habe mir diesen AMS-Stand konstruiert weil meine ganzen Utensilien die ich am Drucker benötige ständig irgendwo rumliegen.Dieser ist komplett zum zusammenstecken und es muss nichts geklebt oder geschraubt werden.Der Zusammenbau ist nahezu selbsterklärend und kann ohne Probleme von jedem durchgeführt werden. &nbsp;Ich habe jetzt zusätzlich einen Druckplattenhalter für 5x Platten konstruiert.Dieser kann ohne Probleme auf den AMS-Stand gesteckt werden und dann das AMS auf den Drucklplattenhalter.Jetzt kann man sich frei wählen ob man den 5-Fach-Halter oder den 3-Fach-Halter nimmt.Oder beide :-)&nbsp;Ich habe als Option einen Druckplattenhalter für 3-Platten konstruiert der je nach Wunsch mit dazu gedruckt werden kann.►Wenn der AMS-Stand ohne Druckplattenhalter verwendet wird benötigen Sie die Pos. 013-TPU-Feed-6x►Wenn der AMS-Stand mit Druckplattenhalter verwendet wird benötigen Sie Pos. 070-Connector-Pin-4x und Pos.080-TPU-Feed-4x►Der Druckplattenhalter wird mit Hilfe der Connector-Pins verbunden. Die Drehrichtung gibt der Pfeil auf dem Pin an.►Für die Schubladen habe ich ein Schild gemacht das individuell beschriftet werden kann ( Bambu-Studio ) ►Diese Schild ist zum einklippsen damit es gewechselt werden kann.►Das Bambu-Logo ist auch nur zum stecken und hält bei mir sehr gut.►in den beiden Seitenteilen und dem Mittelteil ist ein durchgehendes Loch in das Sie je nach Ihren wünschen Filament mit dem Ø1,75mm einschieben können um dem ganzen einen Farbtupfer zu geben :-)►ich habe mich für PLA-Bambu-Green entschieden da mein AMS-Stand auch diese Farbe enthält.►gedruckt habe ich diesen Stand komplett in PLA ►Bambu-PLA-schwarz Basic►Bambu-PLA-weiß Matt►Bambu-PLA-Bambu-green&nbsp;Ich werde in naher Zukunft für die Schubladen noch Einsätze konstruieren für die verschiedenen Bambu-Ersatzteile und diversen Dinge die man so für seinen Drucker hat.&nbsp;

AMS-Stand with optional Buildplateholder 3x or 5x

bambu

brody.bolanos

Bambu Lab P1P Printable Cable Drag ChainI created a printable cable chain for the p1p as not everyone has access to the cable chain from Amazon that I linked in my other design <a target="_blank" href="https://makerworld.com/en/models/23653" rel="nofollow noopener">https://makerworld.com/en/models/23653</a> . There were a few things that I wanted to meet or exceed from the store bought design including a reduction in sagging and lighter weight. <ul><li>Chain has a minimum bending radius of 18mm, making sure the wire doesn't get over bent.</li><li>When fully extended ( side with the latches face down) the chain has a slight curve, meaning it wont lay completely flat. This is intentional to make sure the chain wont accidently bend the opposite way.</li><li>Each of my links weigh 1.963g and the cable chain links from amazon weigh 2.160g. </li><li>Below you can see the difference in sagging with the chains fully extended.</li></ul>Please use <a target="_blank" href="https://makerworld.com/en/models/23653" rel="nofollow noopener">https://makerworld.com/en/models/23653</a> for the rest of the instructions and print files for the complete assembly. &nbsp;This is a 3d printed chain with a lot of moving parts, overtime tolerances will loosen and it will start to wear down. I haven't had any issues so far but the Amazon chain is still a better option overall when it comes to durability and smoothness. <figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/244611/2023-09-27_j3urpsw5m7fl.jpg"></figure><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/244611/2023-09-27_0djvy4hh02bh.jpg"></figure><blockquote><h3>Files</h3></blockquote>Main Files<ol><li>Chain Link Latch</li><li>Chain Link Latch PTFE Clip</li><li>Chain Link 0.0</li></ol>Alternative Files<ol><li>Chain Link -0.02</li><li>Chain Link +0.02</li></ol>Print Files<ol><li>Printable Cable Drag Chain Assembly</li><li>Printable Cable Drag Chain Test Print</li></ol><blockquote><h3>Parts/BOM</h3></blockquote><ul><li>22 Chain Link Latch</li><li>22 Chain Link 0.0</li><li>1-3 Chain Link Latch PTFE Clip ( I used one on the 11th link)</li></ul><blockquote><h3>Print Orientation</h3></blockquote><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/244611/2023-09-27_dwzfge3tu4g9.png"></figure><ul><li>The PLA/+ printing preset for cooling uses the Aux fan, I don't know how much it effects the print as the fan blows from one side but I kept all the male sides of the links facing towards the fan. </li></ul><blockquote><h3>Print Setting</h3></blockquote>Filament Tested - eSun PLA+, Bambu Tough, Polylite PLA Pro (dried and kept around 20%RH). DO NOT USE PLA, IT WILL BREAK<ul><li>See print file</li></ul>Supports<ul><li>None</li></ul><blockquote><h3>Before You Print</h3></blockquote>In the Files section you might have seen two alternatives Chain Link Files.<ol><li>Chain Link Final -0.02</li><li>Chain Link Final +0.02</li></ol>These alternative files change the hole sizing slightly in the cable links. 0.0 worked perfectly when using PLA + but when I switched over to PETG I had to tighten the tolerances, making the hole smaller, hence the +0.02 file. Alternatively, -0.02 will expand the hole . More under “Assembly” below.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/244611/2023-09-27_2n9xykfuj8sc.png"></figure><blockquote><h3>PETG Note</h3></blockquote><ul><li>It seems like a hit or miss with PETG, as a small percentage of users couldn't get good prints ( including me). If you are having issues with the tolerances being too lose please comment or message me and I will send you + 0.03/0.04 files. </li></ul><blockquote><h3>Assembly</h3></blockquote><ul><li>Print Printable Cable Drag Chain Test Print</li><li>Once you've printed the test file, press the matching links into place, in total 3 small chains consisting of (0,0,0) (+.02,+.02,+.02) (-.02,-.02,-.02) . It's kind of hard but a little easier if you slide the links together along the chamfer on each cylinder. </li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/244611/2023-09-27_g6fawy05urym.png"></figure><ul><li>Next snap the latches into place</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/244611/2023-09-27_11ru8ghqjsnh.png"></figure><ul><li>What you're looking for initially is a snug fit, after rotating the pieces back and forth a handful of times they'll loosen up and you should be able to figure out which sizing is correct. There should be very little movement (almost none) when wiggling the links in any other direction other then rotating. If you have PLA + I would suggest doing the test print in that ( pla should work fine for this but the pieces will definitely break ) reasoning being I know PLA + gives a good fit and even you you want to print in something else, it'll help you get a good idea of how it should feel. </li></ul><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/244611/2023-09-27_a9kvyeohlog5.jpg"></figure><ul><li>Once you've figured this out, use the file Printable Cable Drag Chain Assembly ( which is sized at 0.0) to print out 22 links, 22 latches, and 1 PTFE latch ( or more ). Or use another sizing!</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/244611/2023-09-27_qxbgr6led8o5.png"></figure><h3> </h3><h3>Make sure to recalibrate after the chain is installed. </h3>&nbsp;<blockquote><h3>Tips</h3></blockquote><ul><li>I only used 21 latches including the PTFE latch, I forwent the first latch on the link (the side closest to the frame) </li><li>To remove the latches, insert a small flat head screwdriver and twist. </li></ul><h4>Be careful where you place the PTFE clips, one in the middle is enough. Additional locations can cause the PTFE tube to put unwanted force on the chain.</h4>&nbsp;<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/244611/2023-09-27_jdfxwg6vkfon.jpg"></figure><h3>Please use <a target="_blank" href="https://makerworld.com/en/models/23653" rel="nofollow noopener">https://makerworld.com/en/models/23653</a> for the rest of the instructions and print files for the complete assembly. </h3>&nbsp;If you like my designs and want to say thanks, you can buy me a coffee and help fund the filaments I need for prototyping. A donation of any amount to <a target="_blank" href="https://www.buymeacoffee.com/brodyB" rel="nofollow noopener">Buy Me a Coffee</a> or <a target="_blank" href="https://paypal.me/brodyb10?country.x=US&locale.x=en_US" rel="nofollow noopener">PayPal</a> would be greatly appreciated!&nbsp;<h3>As always, given different printing environments, filaments, etc., prints may not work perfectly for everyone. If you are having issues please message or comment and I will try my best to resolve the issue.</h3>

Bambu Lab P1P Printable Cable Drag Chain

Bambu p1s 

XmonikerX

Volkswagen MKII (MK2) Golf Wall Art Silhouette.This should be roughly to scale, with the other VW Golf Silhouettes I have posted as well.&nbsp;Quick print that uses under 15g of filament.

Volkswagen MKII (MK2) Golf Wall Art Silhouette.

Leif3D

Ein 3D Druck Gutschein im Kreditkarten Format. Durch seine Größe passt er in viele der kleinen Gift Boxes hier. English version: <a target="_blank" href="https://makerworld.com/de/models/95138#profileId-101621" rel="nofollow noopener">3d print coupon christmas credit card size by Leif3D - MakerWorld</a>&nbsp;&nbsp;

3D Druck Gutschein Weihnachten Christmas Kreditkartengröße

SavageLau

<h3>If you want commercial license, check out my bio and get it from Patreon. </h3>&nbsp;&nbsp; So, this design is for trophy contest. I just pull some of my work in the past to start with. I have piston, rod, and connecting rod. I was wantted to have some assembly elements in this design. So you can put some of the bolts and part together. But it end up the bolts are too small, also if you are printing with silk filament. The bolts will not have enough strength. so, I turn it into semi assembly.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/399846/2023-12-18_aa9524933254d.png"></figure>Made some change.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/399846/2023-12-18_8dc3d7d04074e.png"></figure>Get more detail:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/399846/2023-12-18_5a4183f632025.png"></figure>Here we go:<figure class="image image_resized" style="width:51.33%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399846/2023-12-18_0a31cc4919c56.png"></figure>&nbsp;&nbsp;From this:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/399846/2023-12-18_b71c438d560e9.png"></figure>To this:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/399846/2023-12-18_f744704adaff2.png"></figure>But, if you want the full assmebly version, wait for my update.<figure class="image image_resized" style="width:53.09%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399846/2023-12-18_7658b80e2912c.jpg"></figure><figure class="image image_resized" style="width:52.41%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399846/2023-12-18_59a0e6c8e7e2a.jpg"></figure>You could still adjust the piston position:<figure class="image image_resized" style="width:64.6%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399846/2023-12-18_863a168c1e66f.jpg"></figure>

Piston Trophy semi-assembled

Ian Smalley - hueforge

Filament painted print made using HueForge - Filament swaps ONLY, no mmu/ams required&nbsp;3 Colour ‘Filament Painting’ model - Op-Art White Tiger Portrait, made using Bambu filaments.&nbsp;(I recommend the following speed settings for the bambu with 0.04 layers, inner walls, outer walls and gap infill - 200mm/s, sparse infill, internal solid infill and top surface - 150mm/s)Leave The Aux fan off on the bambu as it causes more harm than good on these larger prints&nbsp;Print at 100% infill with a layer height of 0.04mm with a base layer of 0.24mm&nbsp;Filaments Used: PLA Bambu PLA Matte Charcoal Transmission Distance: 0.6 PLA Bambu PLA Tough White Transmission Distance: 12 PLA Bambu PLA Matte Ivory White Transmission Distance: 4&nbsp;Swap Instructions: Start with Charcoal At layer #7 (0.48mm) swap to White At layer #22 (1.08mm) swap to Ivory White for the rest.&nbsp;This is a filament blending model, I would recommend trying to match the td as close as possible if not using the exact filaments to get the best results.Use the exact numbers in your slicer to match up properly.Two different size models are supplied and designed to print with 0.4 nozzle **If Scaling the model make sure not to adjust the Z-Height of the model**&nbsp;ALL of Ian Smalley's designs are protected by Copyright Law. Downloading does not give you permission to use the files or physical prints for financial gain. If you want a commercial license to Legally sell prints from my designs, you will need a SELLER subscription.

Op-Art White Tiger (Filament Painting)

Kunst 

pixelwave

A detachable bottle and smartphone mount for a 25mm pole (+/- 3mm). The chair mount I printed in Prusament PETG, the bottle holder in Prusament PLA.&nbsp;Additionally the design uses:6x M5x16 mm Screws + M5 Nuts2x Rubber Bands (optional to place inside the clamp groves)&nbsp;I also attached the Fusion 360 File for further modifications. Please link if you upload modifications! :)&nbsp;@UPDATES:221014 - V5<ul><li>added a large version (fits 10cm 1,5L bottles) Bottle Holder V3 - 10cm</li><li>old size still available Bottle Holder V3 - 8.8cm</li><li>changed alignment of holes for easier print</li></ul>220822 - V4<ul><li>Updated Bottle Holder V2 with two compartments and symetric mounting option</li></ul>220523 - V3<ul><li>Changed tolerance of mount (-0.1mm)</li><li>Rounded Corners for better insertion</li></ul>220522 - V2<ul><li>Changed tolerance of mount (-0.2mm)</li></ul>_______If you like my uploads buy me a coffee -> <a href="https://bit.ly/pwave-donate" rel="nofollow">https://bit.ly/pwave-donate</a>

Fishing Chair Bottle & Smartphone Mount (Carp On)

hirt.3dprint

I had a wobble on my rear z rod.I made this little bushing to fix this issue. I printed 4 of it in different heights for variation to adjust the gap between the z rod and the top bearing (2x 0.6mm, 1x 1mm & 1x 2mm) Print in ABS or at least PETG.0.2mm ProfileYou can change the height in your slicer for your own need.Remove both screws above the rear z rod bearing. Go with a small pick or allen wrench from underneath the bearing and pusch it slowly out (left, right, left, right ;) be careful it pops out and will fly). Install for example the 1mm and pusch the bearing back. Check if the wobble is still there and adjust with other bushings if needed (for example a 0.5mm on top of the 1mm)

Creality K1 rear z rod wobble bushing

k1 max

Modular Mapping

This is a Bier sign which can be filled with RGB-LED Strips. it has also printable front windows which i printed in a transparent PLA. Its mostly selfexplaining but i will describe shortly how i did it.First of All: DONT FORGET TO MIRROR THE LETTERWINDOWS. They need to be Mirrored cause they will be flipped to be attached.First print all the Letters, then the caps to close them while assembling the LED-stripe. I soldered multiple pieces together so the inside of all Letters has enough Led-stripes. begin with the first Letter and end with the last one. test the Led Stripe before you go to the next letter so you dont have to redo everything (did not happened to me...). Take care of good ventilation while soldering and take care to disconnect the led strip after testing to prevent shorts.Have fun while drawing attention to beer :)

LED Bier Sign

interessant 

uhltimate

Description:Introducing our innovative Disc Shooter – a print-in-place marvel that launches discs over 10 meters! This cutting-edge design requires no assembly, providing instant shooting excitement.&nbsp;Features:<ul><li>Print-in-Place Magic: No assembly hassles. Print it, and it's ready to shoot!</li><li>Impressive Range: Launch discs with precision over 10 meters.</li><li>Quick and Easy Reload: Experience continuous fun with swift and hassle-free reloading.</li><li>Compact and Portable: Take the excitement anywhere with this portable and compact design.</li></ul>&nbsp;Safety Guidelines:<ul><li>Aim responsibly, avoiding people, animals, or fragile items.</li><li>Always wear eye protection.</li><li>Keep the disc shooter out of reach of children.</li></ul>&nbsp;Printing Tips:<h2>“set wall loops to 6 !”</h2>(or more ;-)Choose a durable filament for longevity.Ensure precise calibration for accurate dimensions.&nbsp;Mesmerizing Discs with colorized pattern by @BamBam Design<a target="_blank" href="https://makerworld.com/en/models/108108#profileId-115446" rel="nofollow noopener">https://makerworld.com/en/models/108108#profileId-115446</a>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/312570/2023-11-15_c5ba731bcdf4d.gif"></figure>

Disc Shooter - with Performance - Print-in-Place Design

Spielzeug 

OlleMark

A tool to clean out the dust from your blower fans.&nbsp;Designed and tested on my p1p&nbsp;My recommended settings:0.4mm nozzle0.2mm layer height0.42mm line width20% infill&nbsp;A drawing is provided if you want to design some kind of holder for it :)<figure class="image image_resized image-style-align-left" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/144611/2023-11-04_fpomihzmxmw0.png"></figure>

Bambulabs Fan Dust Cleaner

Tools 

impietro

This is my behavior when I want to do something, a little slogan it describes. You too, Stop! Think, Draw and print.

dajana

angeln

muss tool

garten

Kay

Auto

Auftrag

löten

lockcard

Angeln

Arbeitskollege

love

ams

wled

voron

gridfinity

Corona

test

Beer

Kaffee

lern Spielzeug

3d drucker Ideen

sexy

technisch

Lampen

haushalt

ams

nächste Projekt

Bambu umarbeiten

Büro

ps5

bambu

Bambu p1s

Auto

Lampen

technisch

Kunst

Angeln

k1 max

interessant

Spielzeug

Tools

Wohnung