jeffsjonesbjj

Amao Chan

This is an African elephant with 22 movable joints. The joint design of this elephant is different from the common chain-like design. These joints can be adjusted and fixed at different angles, allowing the elephant's trunk to be lifted and posed in various preferred positions. The tightness of the joints depends on the hardness of the materials used for printing. Using harder materials will result in tighter joints.&nbsp;The reason it is named "Blank" is to encourage the printer to add color to the elephant's body. For those with multi-color 3D printers, they can try printing each segment in different colors.&nbsp;When printing, please start by printing the tail. If the tail can rotate properly, then use the same printing settings to print the other parts. If the tail gets stuck and cannot rotate, please reduce the material flow to continue printing.&nbsp;3D printing settings Layer height - 0.2mm Infill Density - 12% No supports. <a target="_blank" href="https://www.facebook.com/amaochanstudio/" rel="nofollow noopener">https://www.facebook.com/amaochanstudio/</a> <a target="_blank" href="https://amaochan.work/" rel="nofollow noopener">https://amaochan.work/</a>&nbsp;多關節素坯非洲象這是一隻有22個可轉動關節的非洲象這隻非洲象的關節設計與常見的鍊條式的設計不同，這種關節可以調整角度後固定，因此這隻大象的鼻子可以抬起並且擺出自己喜歡的姿態。大象的關節結緊迫程度與使用的材料硬度有關，使用愈硬的材料列印則關節的緊度愈緊。之所以取名為(白胚)的原因，就是鼓勵列印者能幫大象的身體上顏色，若有多色3D列印機的朋友就可以試著在每一段使用不一樣的色彩列印。&nbsp;列印建議 列印時請先列印尾巴，若尾巴能正常轉動，就以相同列印設定來列印其他部分。若尾巴卡住無法轉動，請減少材料流量來列印。 層高-0.2mm 免支撐 填充-12%

BLANK ELEPHANT

zoey

signes01

&nbsp;bambu 3dprinter poop bucket<figure class="media"><div data-oembed-url="https://youtu.be/I9YvycCDbJU"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/I9YvycCDbJU" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/221699/2023-11-30_e53ade2af556b.png"> The door handle can be removed by applying force. When re-gluing, use instant adhesive.

bambu 3dprinter poop bucket Ver2

printer

cdc mkb

This is a simple necklace holder composed of two parts that are easy to print and to assemble using glue. It was designed by my daughter who is willing to share it to the world :D

Necklace holder 

Carolina 

NUKDDD

“Fudget! I'm printing this!” - You, Nov 2023&nbsp;Fudge in fudge in fudge…the Fudget Toy is born! 12 segments of fudgeption in this fidget, can you resist?&nbsp;No support, easy print in place fidget toy, it's time to Fudget!

Fudge in Fudge....Fudget!

eazy

Infinity 3D Prints

&nbsp; 𝑳𝑰𝑲𝑬 𝑨𝑵𝑫 𝑭𝑶𝑳𝑳𝑶𝑾 𝑷𝑳𝑬𝑨𝑺𝑬 !! <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/199853/2023-11-23_b01acf5164f6c.gif"></figure>CAN BE WINDOW ART WITH DOUBLE SIDED TAPE OR BLUE MAT TAC OR CAN BE A MAGNET WITH ADDED MAGNET ON THE BACK -( 8x2 is a good choice)USE HOT GLUE TO ATTACH (or ca super glue )IF YOU WANT FOLDED WINGS , JUST HIT IT WITH A HOT AIR GUN FOR A FEW SECONDS (or a lighter) Try not to burn your print !! &nbsp;REMEMBER TO LIKE AND FOLLOW!! &nbsp;Commercial license can be found on Cults 3D &nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/199853/2023-11-23_9b13815b1231c8.gif"></figure>&nbsp;https://cults3d.com/en/3d-model/art/monarch-butterfly-3-layer-0-6mm-magnet-or-window-decoration

MONARCH BUTTERFLY - 3 LAYER 0.6MM -WINDOW STICKERS OR FRIDGE MAGNETS / FAST EASY PRINT !! 

decor

berri3D

This card kit makes a customizable Halloween haunted house diorama. The trees, pumpkins, ghosts, and tombstones are all interchangeable. Mix and match to make your own creation!<ul><li>Great for party favours; print in different colours and swap with friends!</li><li>Multi-colour ready</li><li>Separate (not attached to a card) pieces are also included in the .3mf</li></ul><h3>Trouble? Questions? Comments? Please don't hesitate to get in touch</h3><h3>Happy Halloween and Happy Printing!</h3><h3>Tolerances and fit</h3>All pieces should fit snugly. The smaller pieces are a bit fiddly due to their size. I recommend assembling with the smallest pieces first, followed by the gate, the tree(s), and, finally, the house.&nbsp;IMPORTANT: print the tolerance test first. Minor differences in filament flow can mean the difference between fitting and not fitting. This test is comprised of three pieces from the model as this is the most accurate way to gauge how well it will fit. <ul><li>Too tight? Change the X-Y hole compensation setting to 0.05 mm and reprint. Adjust up or down as needed.<img src="https://makerworld.bblmw.com/makerworld/draft/545096/2023-10-25_10a1e251c2ff9.png"></li><li>Too loose? Change the X-Y hole compensation setting to -0.05 mm and reprint. Adjust up or down as needed.<img src="https://makerworld.bblmw.com/makerworld/draft/545096/2023-10-25_8e82d3e6d8716.png"></li></ul><h3>Print Settings</h3>The .3mf files include my recommended print settings:<ul><li>Nozzle size: 0.4 mm (don't change as it may prevent pieces from fitting together)</li><li>Plate type: Smooth PEI Plate/High Temp Plate (best results)</li><li>Layer height: 0.2 mm (don't change as it may prevent pieces from fitting together)</li><li>First layer speed: 15 mm/s (slow to prevent small details from coming loose from the plate)</li><li>Wall order: outer/inner (for the same reason as above)</li><li>Wall generator: Classic (don't use Arachne because it will throw off the tolerances)</li><li>Brim: none</li></ul><h3>Filament settings</h3><ul><li>This model has been tested using the default uncalibrated “Generic PLA” preset with multiple filaments from various manufacturers. </li><li>If you find that the top surfaces are rough, reduce filament flow ratio. Caution: this may change fit so reprint the tolerance test first.</li><li>If you're using a custom filament preset, your results may vary.</li><li>Display models were printed in PLA as follows: Orange (Eryone), Grey (Eryone), Purple (AMZ3D), and Black (AMZ3D).</li></ul><h3>Multicolour</h3><ul><li>The model is AMS multicolour ready and provided pre-painted.</li><li>If you prefer to paint it yourself, I recommend leaving the first layer as one colour as it will help with adhesion. However, each bottom surface is isolated and paintable if you should so choose.</li><li>DON'T print your multicolour masterpiece without first printing the tolerance test!</li><li>Print four at a time to reduce filament waste (X1C and P1P/S only; A1 mini can only fit one)</li></ul><h3>About the model</h3>I've always enjoyed card kits and thought it would be fun to design my own to hand out at Halloween to trick or treaters. As with most things I create, it became more complicated as I went on and I lost the original intent of being an all-ages kit. However, I did wind up with what I think is a fun miniature diorama that older kids and adults might enjoy. If this kit is well received, I may design diorama kits for other holidays. Let me know what you think!&nbsp;P.S. I'm working on a simpler kit for younger users; I will update this when it's published. Update: done! Find it <a target="_blank" href="https://makerworld.com/en/models/52381#profileId-54144" rel="nofollow noopener">here</a>.<h3>Licensing</h3>This kit is non-commercial and may not be sold, reproduced, or shared outside of this website. However, I will consider an individual license fee if you wish to sell printed models in your local area such as at a craft show. Please contact me for details.------------------------<h3>Changelog</h3>January 8, 2024<ul><li>Updated description to align with changed MakerWorld TOC</li></ul>October 24, 2023<ul><li>Initial upload</li></ul>October 25, 2023<ul><li>Added print profiles for A1 mini</li><li>Removed multiple plates for solid and multicolour profiles to give a better estimate of individual model print times and filament usage.</li><li>Changed XY contour compensation to XY hole compensation</li></ul>October 29, 2023<ul><li>Added link to Trick or Treat House card kit</li></ul>

Halloween House Diorama Card Kit

halloween

MEAF designs

Easy to print and fun to make!Perfect for your candy table, coffee table or any corner of your house&nbsp;&nbsp;Specially designed to fit in the buildplate of any mid size printer.The base is one piece. and every letter and details are separated files so you can print it in different colors even without an AMS.&nbsp;Designed two styles for every “O”. so you can choose what you like.<ul><li>First "O": choose between santa claus or tree ornament</li><li>Second “O”: choose between snowman face or snowman body</li><li>Third “O”: choose between reindeer or christmas elf</li></ul><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/1795494732/draft/2023-09-02_n84evi4tipld.gif"></figure>&nbsp;split the "Details" file in to parts with your slicer and just print the details you like for each one and glue them on top!<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/1795494732/draft/2023-09-02_o1xtzxx4tz4i.png"></figure>&nbsp;&nbsp;&nbsp;Print SettingsMaterial: PLA / PETGLayer height: 0,28 mm for letters and base. --- 0.2 for detailsNozzle diameter: 0,4mm or 0,6mmInfill: 10 -12%Perimeters: 2Supports: no&nbsp;Printing Tipthe tolerances are a little tight, so you will need some glue depending on your printer and/or filament calibration&nbsp;&nbsp;&nbsp;

Christmas hohoho Sign

xmas

MakeIt3D

<h2>Summary</h2>Tired of receipts, dust, and other debris clouding your workspace?This 3D Printable Mini Trashcan is the perfect tool for throwing away, storing, or disposing trash and other belongings.This print features a fully functioning built-in swing allowing you to store items inside without things accidently falling out.This item is easy to print featuring 2 main files<ul><li>LID STL</li><li>Bottom STL</li></ul>Total Size of the product is roughly 6 inches Height, 3.5 inches Width, 3.5 inches Length.Feel free to print out the designs and share photos of your results. I would love to see them. All MakeIt3D Designs are made and designed in-house. When you purchase any of these designs you do NOT have the rights to sell the digital files or printed models. 3D PRINTING SETTINGS Printer Used: Bambu Labs X1 Layer Height: 0.2 Infill: 10% - 15% Honeycomb Print Speed: Slow Speed on First Layers Material: PLA Wall Count: 2 Walls