Jaszi

nickollaamir

Note: Model originally by Matija (@Matija_272939) on Printables&nbsp;As stated above, this I did not create this model, but I did like it so much that I wanted to share it here too as it printed great on my X1 Carbon. I've included the 3mf for printing this in PLA. I personally printed it in PAHT-CF with ABS as a support interface (it works really well).&nbsp;Note that the addition of this prop guard means the Mini SE no longer fits in the under 250g lightweight drone category - do with that information what you will.&nbsp;&nbsp;Description from Matija's original post on Printables:&nbsp;Printed with 0.4 nozzle, brim for extra adhesion and supports. Sharp small scalpel is recommended to remove brim and extra material I've put on holders so it can be printed, it's only 1 wall thick and should be visible line that follow the contour of the drone.After that just click everything in place but be aware that on front end one of the hands is shorter than the rest.Since I've made this I have not tested it much so if you think it can be improved I can make adjustments.

DJI Mini SE/2 - Minimal Propeller Guard

drone

okywan

The knot helper that almost ties the knots for you! As seen on: &nbsp;<figure class="media"><oembed url="https://www.youtube.com/watch?v=XMdJziq2S2k"></oembed></figure>&nbsp;There&#39;s a version for different hand sizes. Please pick the one you feel most confortable with.&nbsp;&nbsp;

Easy Knot! Your knot helper.

Fishing

GlennovitS 3D

Need to organize your Gridfinity boxes to store and organize your bits and pieces, screws and bolts in your messy drawer or on your desk - then print some Gridfinity baseplates! These are quick to print and use way less filament.These are for you who doesnt need the magnet-part of the gridfinity system.<figure class="image image_resized image-style-align-right" style="width:357px;"><img src="https://media.printables.com/media/prints/478930/rich_content/619c60c9-d94d-42be-91d9-be3611154a9e/thumbs/cover/800x600/jpeg/img_0185.webp"></figure><h3>Sizes</h3>Files are named AxB<ul><li>A: Width of the grid (each section is 42 mm)</li><li>B: Length of the grid (each section is 42 mm)</li></ul>Baseplates come in sizes from 1x2 (42x84 mm) to 6x6 (252x252 mm)<h3>Assembly</h3>To get compatible boxes, use the quick boxes for the gridfinity system. Use the model here : <a target="_blank" href="https://makerworld.com/en/models/63554#profileId-66513" rel="nofollow noopener">https://makerworld.com/en/models/63554#profileId-66513</a><h3>Print instructions</h3>These tips can maybe help<ul><li>Speed on first layer: 50% (or less) (To ensure good bed adhesion and perfect fit)</li><li>Infill: 0% (Not needed - they doesn’t hold weight but just place the boxes)</li><li>Perimeters: 1-2 (1 works just fine in my drawer - printet on 0.6 mm nozzle)</li><li>Supports: NO supports - that would prevent you from spinning the faces afterwards.</li></ul>Happy printing!&nbsp;Want to show your support?You can see all my designs on Printables - and you can become an active supporter. I would really appreciate it!<a target="_blank" href="https://www.printables.com/@GlennovitS3D" rel="nofollow noopener">https://www.printables.com/@GlennovitS3D</a>&nbsp;And special thanks to Zack Freedman

Gridfinity Baseplate (Quick print, lite version, less filament)

Gridfinity

Iconic FAB

Universal valve cap for car or bike. Print and screw new one and you are ready to go.Recommended print settings<ul><li>Layer height: 1.6-0.2mm.</li><li>Extrusion width: 0.4mm, forced.</li><li>Infill percentage: > 40%</li><li>Walls: 4</li><li>Solid top/bottom layers: 4.</li><li>Supports: None</li></ul>Recommended filaments<ul><li>ABS, ASA, ASA-CF, PETG-CF, PETG</li></ul>

Car or bike valve cap

hartmann82

This is a milti Board Tile 8x6, corner core and side

Multiboard Parametric

Multiboard

Shaggys3D

If you want commercial access please sub to me at Patreon.com/LightBoxGaloreI will be doing the ps5 and nintendo switch ones as well soon when i can get the controllers in hand.Not yet satisfied with the back pieces they still need some adjusting but the front is pretty good now that ive been gaming for a couple days with it for testing with no issues.After printing i rec sanding the holes especially for the joysticks so its smooth and wont damage the joystick.

Xbox Series S/X Controller Faceplate

Xbox

Art Design. 3D

Hey there,&nbsp;the Organizer Desktop Skadis Box in Line Art horizontal is here!&nbsp;If you like the model, I would appreciate it if you could take the time to like, follow, or boost it. That helps me continue to create great models for you. Thank you very much in advance.&nbsp;You can use it for what ever you can imagine! If u dont need it anymore on your desk, you just simple hang it back to the skadisboard.&nbsp;For the HOLDER, u need 2 of them visit !!!<a target="_blank" href="https://makerworld.com/en/models/174221#profileId-191522" rel="nofollow noopener">HERE</a>!!! (not compatible with HSW)&nbsp;Watch my collection for even more Skadis accessories <a target="_blank" href="https://makerworld.com/en/u/4108147586/collections/558836" rel="nofollow noopener">!!! HERE !!!</a>&nbsp;I´m going to upload several boxes in the next period of time.I designed these boxes, because all I found where not suitable to hang up without destroying the aesthetics.They need a little more printingtime but I think they are worth it.Also check out my other designs in my <a target="_blank" href="https://makerworld.com/en/u/4108147586/collections/558836" rel="nofollow noopener">COLLECTION</a>If you like my work and want to support me you can buy me a coffee <a target="_blank" href="https://www.buymeacoffee.com/big_kev3d" rel="nofollow noopener">HERE</a>If you have any special requirements and need a personalized box: just hit me up, I´ll try my best to design it for you.

Organizer Desktop Skadis 

Skadis

Balzo98

You love Snorlax?Here for you the cutest Snorlax model on the internet!&nbsp;I used a picture found on Pinterest as reference.

Cute Snorlax

Cute

Every Day Counts

Introducing the BIG brother to the “Waffle” trash can family. This guy is a bully!&nbsp;This is a HUGE, sturdy, basic bin that is great for the office desk, bathroom, kid's room or right next to your fancy 3D printer.&nbsp;The size is 200mm square at the top and 330mm high (with lid). It almost needs its own room.  This is a serious print, requiring 3/4s of a roll of filament and a lot of printer time, but sometimes you just need to do it!&nbsp;The photographed print was printed using the Bambu Matte Lime Yellow filament.&nbsp;What more to say? Only, as always, please leave a comment, photo and fantastic rating.&nbsp;There are now 3 bins in this series - find them all on my profile page.<a target="_blank" href="https://makerworld.com/en/u/369067369" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/423012/2024-01-19_fa5d88a7c8895.jpg"></a>

The Large "Waffle" Trash Can with Lid

House stuff

I3Design

Do you have a Bambu Lab printer? Does the cable chain gets stuck on a screw when printing? I have the solution! Just print the cover with the arrow showing up and clip it on the sheet metal.<img src="https://makerworld.bblmw.com/makerworld/draft/298528/2023-12-22_e49dcfc95e5f5.png">You want to pull it of again? Just push it downwards.&nbsp;No supports for this model :-). I recommend printing with PLA+/tough or PETG. Tested this on my P1S. Might also work on a X1? Someone might test it out.&nbsp;Save your cable chain folks! Happy printing.

Bambu Lab Cable Chain Guard

Printer upgrades

Regarnogal

simple sanding stick to rework printed parts much easier.added Bambu Logo to better fit the Maker World :D&nbsp;Need a sanding paper of1,5 cm width14 cm length<img src="https://makerworld.bblmw.com/makerworld/draft/494064/2024-02-04_ee343ecc90525.jpg">&nbsp;&nbsp;Also have a look on the bigger Version with 2,5 cm:<a target="_blank" href="https://makerworld.com/en/models/171216#profileId-187972" rel="nofollow noopener">Sanding Stick Bambu Style V2 (Big version) by Regarnogal - MakerWorld</a><img src="https://makerworld.bblmw.com/makerworld/draft/494064/2024-02-04_88f299a34118c.jpg">&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/494064/2024-02-04_e96db8f2379a7.png">&nbsp;Details for this Version:tick_width_in_millimeter = 15 base_height_in_millimeter = 12 base_length_in_millimeter = 50 end_1_option = wedge end_1_height = base_height end_1_wedge_angle = 23 end_1_wedge_round_tip_diameter_in_millimeter = 2.0 end_2_option = round end_2_height = base_height end_2_wedge_angle = 10 end_2_wedge_round_tip_diameter_in_millimeter = 3.0 screw_thread_dia_in_millimeter = 6.0 screw_head_dia_in_millimeter = 12.0 screw_thread_hole_dia_in_millimeter = 6.4 screw_hole_dia_in_millimeter = 6.6 screw_head_space_in_millimeter = 15.0 screw_head_teeth = 8 extra_screw_head_height_in_millimeter = 0.0 max_thread_height_in_millimeter = 3.5

Sanding Stick Bambu Style

Tools

SMichaud

Lot of bearing.Important print in 0.12 or lower, if you print bigger (0.16/0.2/0.24 etc..) the pieces will merge.&nbsp;For imperial bearing → <a target="_blank" href="https://makerworld.com/en/models/146209#profileId-159197" rel="nofollow noopener">https://makerworld.com/en/models/146209#profileId-159197</a>&nbsp;

Print in place Bearing metric

Random

ObiYanKenobi1980

Rear fender for scooter Dualtron Spider 2 allow you to use 10x3 tires insteand of 10x2.25 stock tires.

Dualtron Spider 2 Rear Fender for 10x3 tires

Bike

Chester3D

&nbsp;IntroductionThe original model is designed for printers with a 250x250mm bed.&nbsp;If for any reason it doesn't fit on your bed, you can resize the model to the size you want from your slicer.&nbsp;It consists of two parts, the lamp body (body.3mf) and the rear cover (lid.3mf).Sometimes I include two lids, with and without a hole (choose the one you want, I recommend printing the Lid with hole whenever possible, to be able to remove the LED cable).&nbsp;If the back cover does not have a hole, you can easily make it from Bambu Studio, or from any other slicer you use.&nbsp;----&nbsp;You will need&nbsp;<ul><li>LED Strip: <a target="_blank" href="https://s.click.aliexpress.com/e/_DekFgj1" rel="nofollow noopener">https://s.click.aliexpress.com/e/_DekFgj1</a></li><li>- Glue gun or Tape</li></ul>Optional, but recommended:&nbsp;<ul><li>Aluminum tape: <a target="_blank" href="https://s.click.aliexpress.com/e/_DEPgqHd" rel="nofollow noopener">https://s.click.aliexpress.com/e/_DEPgqHd</a></li><li>- Textured PEI Sheet</li></ul>----&nbsp;Assembly instructions&nbsp;&nbsp;You can follow either of these two videos to assemble the lamp. It's very simple, you stick the LED strip inside and that's it. If you want, you can use aluminum tape to improve the lighting, although it is not necessary: &nbsp;<ul><li>Assembly instructions by braga3dprint: <a target="_blank" href="https://www.youtube.com/watch?v=QNsShLmXYh0" rel="nofollow noopener">https://www.youtube.com/watch?v=QNsShLmXYh0</a> (He makes very beautiful designs, you can leave him a follow and help him grow his channel!)</li><li>- Another assembly instructions: <a target="_blank" href="https://www.youtube.com/watch?v=nDUlBp7Mm1c----" rel="nofollow noopener">https://www.youtube.com/watch?v=nDUlBp7Mm1c----</a></li></ul>----&nbsp;Printing settings&nbsp;Following braga3dprint recommendations, you can start with these settings in Bambu Studio:<ul><li>Preferences (CTRL + P) → Activate developer settings → Quality → Advanced → First Layer Flow Ratio: 1.04</li><li>- Quality → Wall generator → Arachne</li><li>- Quality → Wall transitioning threshold angle → 50 degrees</li><li>- Strength → Advanced → Infill/wall overlap → 20%</li><li>- Quality → Advanced → Avoid crossing walls</li><li>- Increasing retraction / reducing temperature can help reducing wisps</li><li>- Order color printing from lightest to darkest color</li></ul>Important! Additional tips Remember to remove the purge line at the start printing, otherwhise it will ruin the print.Adjust the sequence of colors from Light colors to Dark colors, to prevent stringing. &nbsp;

BTS LED Lamp

Gift ideas

Brent Peterson

<h2>Toroidal Launcher</h2>This is an original design created for the <a target="_blank" href="https://makerworld.com/en/contests/5" rel="nofollow noopener">Flying Objects design contest</a> and features a handheld three-stage planetary gearbox that launches a toroidal ring over 3000 RPM! The design is 100% 3D printed; all pieces press fit together and no additional hardware is required.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/360322/2023-12-15_92eaaa9691a14.gif"></figure>The gearbox used in this design is modular and will be released as it's own series soon™, if you have any thoughts or feedback please share so I can continue to improve the design!<h3>Modifications and Add-on Designs</h3><ul><li>[NEW!] Remix Templates<ul><li><a target="_blank" href="https://makerworld.com/en/models/123219" rel="nofollow noopener">Threaded cap</a></li><li><a target="_blank" href="https://makerworld.com/en/models/125073" rel="nofollow noopener">Hexagon gear driver</a></li></ul></li><li>Gearbox modifications<ul><li><a target="_blank" href="https://makerworld.com/en/models/99992#profileId-106623" rel="nofollow noopener">High torque conversion kit (1:2 ratio)</a></li><li><a target="_blank" href="https://makerworld.com/en/models/105586" rel="nofollow noopener">1:3 ratio gearset</a></li><li><a target="_blank" href="https://makerworld.com/en/models/108803" rel="nofollow noopener">1:4 ratio gearset</a></li><li><a target="_blank" href="https://makerworld.com/en/models/105590" rel="nofollow noopener">1:5.5 ratio gearset</a></li><li><a target="_blank" href="https://makerworld.com/en/models/110188" rel="nofollow noopener">1:7 ratio gearset</a></li></ul></li><li>Toroidal ring designs<ul><li><a target="_blank" href="https://makerworld.com/en/models/102279" rel="nofollow noopener">Toroidal Launcher Mini Rings - 100mm pitch</a></li><li><a target="_blank" href="https://makerworld.com/en/models/97633" rel="nofollow noopener">Toroidal Launcher Mini Rings - 150mm pitch</a></li><li><a target="_blank" href="https://makerworld.com/en/models/102728" rel="nofollow noopener">Toroidal Launcher Mini Rings - 200mm pitch</a></li></ul></li></ul><h3>Specifications</h3><ul><li>Three stage planetary gearbox with 1:48 gear ratio (overdrive)<ul><li>0.75mm gear module for ultra-smooth performance (24/72 teeth)</li><li>10mm hex driver for connecting gear stages</li></ul></li><li>Toroidal ring design with four blades (1.2mm thick) available in three sizes<ul><li>100mm diameter, 150mm pitch</li><li>125mm diameter, 175mm pitch</li><li>150mm diameter, 200mm pitch</li></ul></li></ul><h3>Printing tips</h3><ul><li>All prints pictured were printed using Bambu Basic and Matte PLA</li><li>For best results run flow rate calibration and thoroughly clean build plate</li><li>The launcher gears are available in two print profiles with the following changes to the standard 0.20mm profile:<ul><li>Arachne wall generator</li><li>5x top and bottom walls, 25% infill</li><li>75 m/s inner and outer wall print speed</li></ul></li><li>The toroidal rings are available as a single print profile with the following changes to the standard 0.20mm profile:<ul><li>0.6mm line thickness, Arachne wall generator</li><li>75 m/s inner and outer wall print speed</li></ul></li><li>The launcher housing prints with the standard 0.20mm profile.</li></ul><h3>Launcher Parts</h3><ul><li>Launcher Gears<ul><li>SunGear24.step [3x]</li><li>PlanetGear24.step [9x]</li><li>PlanetCarrier24.step [3x]</li><li>RingGearDouble.step [1x]</li><li>RingGearLid.step [1x]</li><li>RingDriver.step [1x]</li><li>GearDriver.step [1x]</li></ul></li><li>Launcher Housing<ul><li>HousingBase.step [1x]</li><li>HousingRingLid.step [1x]</li><li>HousingCarrierHolder.step [1x]</li><li>HousingCarrierThreads.step [1x]</li></ul></li><li>Toroidal Rings<ul><li>ToroidalRing100.step [1x]</li><li>ToroidalRing125.step [1x]</li><li>ToroidalRing150.step [1x]</li><li>ToroidalRingDriver.step [1x]</li><li>ToroidalRingLauncher.step [1x]</li></ul></li></ul><h3>Launcher Assembly (Gears + Housing)</h3><ul><li>Assembly the planet carrier with three planet gears and one sun gear as shown below. Repeat for all three planet carrier assemblies.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/360322/2023-12-31_efae722ebe2db.gif"></figure><ul><li>Use the shorter hex drive to connect two sets of gears. Align both planet carriers and hold them with one hand while holding the double ring gear in the other hand and slowly turning as you close the gear; once closed insert the assembly into the main housing to hold secure. The gears should spin freely; if they don't remove the gear assembly and repeat this step.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/360322/2023-12-31_f1371c6d57ee6.gif"></figure><ul><li>Use the longer hex drive to connect the last set of gears and then assemble with the threaded cap as shown below.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/360322/2023-12-31_4926c45fbbf51.gif"></figure><ul><li>Carefully mesh the single ring gear with the planet gears taking note of the 2mm flat section that is positioned towards the main gear assembly as shown below. Use the same method of rotating while slowly closing and covering with the cap to hold secure.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/360322/2023-12-31_54c6fffceb4e5.gif"></figure><ul><li>Done! The assembly should spin smoothly with the output shaft making 48 rotations for every one turn of the input knob. Performance depends on printer tolerances and filament used; for best results use the include print profiles with Bambu Studio (supports many different printers). A bit of lubricant can also be added to the gears to improve performance.</li></ul><h3>Toroidal Ring Assembly</h3><ul><li>Insert the hex drive into the interlocking driver; the clearance is tight but it should be a snug fit.</li><li>Insert the assembled driver into the output sun gear, the fit should be the same.</li><li>If the driver does not stay secured when launching the ring a small amount of CA glue can be use.</li></ul><h3>Changes</h3><ul><li>v1<ul><li>Initial release; files now available in v1old folder</li></ul></li><li>v1.1<ul><li>Updated print profiles with improved settings for gears and rings</li><li>Improved single color print profile, fits on A1 mini and objects are laid out to allow skipping</li><li>Improved clearance of gears and overall meshing</li><li>Updated toroidal ring to use the same launcher as the mini rings<ul><li>Print profile includes 3 sizes (100mm, 125mm, 150mm)</li></ul></li><li>Updated assembly instructions to have fewer steps with a GIF for each one</li></ul></li><li>v1.1.01<ul><li>Added new section for template designs intended for remixing</li></ul></li></ul>

Toroidal Launcher - High RPM launcher featuring compact planetary gearbox

toys

MBRS

I saw many people used my other creation, the standard desk cable holder, as a way to tidy up passing cables. Since I believe that model is not optimal for that use, I created this version which fits various sizes of cables and in bigger quantities. It is also thinner which makes it ideal behind desks. The size is universal and is compatible with desks up to 40 mm in thickness (though if you have a thicker desk, nothing stops you from scaling Z a little bit).Screw is now optimized and scaled 97.5% from the original model. Should fit nicely with a slight effort on first assembly. Print is quick, about 40 mins, and only uses 18 g of plastic for both clamp and screw. PLA resists fine for me, but you're free to try stronger materials.Let me know if you like it! (Supports in the print profile are very easy to remove, they can be removed in one pull.) 05/01/24 FIXED TOLERANCES