jamie.parkhurst

DesignCraft

A collection of kitchen and bathroom drain strainers, stoppers, and drain pads. Useful for kitchen sinks, bathroom sinks, utility sinks, bathtubs, and probably more!&nbsp;Before printing, please review the list of models and their respective measurements followed by some additional notes.&nbsp;General Notes:<ul><li>The only model that requires support is Part 4 (sink_stopper_4_fin) of the Bathroom Sink Drain Stopper (Experimental).</li><li>No brim is necessary for any of these models.</li><li>Concentric or Archimedean Chords for top and bottom surface patterns works well for many of these models as they're circular.</li></ul>&nbsp;Kitchen Sink Drain Strainer<ul><li>111.5mm outer diameter</li><li>66mm basket diameter</li><li>32.6mm basket depth</li></ul>Voronoi Kitchen Sink Drain Strainer (Experimental)<ul><li>111.5mm outer diameter</li><li>68mm basket diameter</li><li>36.3mm basket depth</li></ul>Utility Sink Drain Strainer<ul><li>72mm outer diameter</li><li>42.6mm basket diameter</li><li>25mm basket depth</li></ul>Bathroom Sink Drain Strainer<ul><li>33mm top diameter</li><li>26mm basket diameter</li><li>51mm height</li></ul>Bathroom Sink Drain Stopper (Experimental)<ul><li>33mm top diameter</li><li>28mm shaft diameter</li><li>130mm height</li><li>The ring (part 5) must be printed in TPU filament (or similar)</li></ul>Large Drain Stopper Pad<ul><li>150mm diameter</li><li>TPU filament (or similar)</li><li>Engineering plate (or similar smooth built plate)</li></ul>Medium Drain Stopper Pad<ul><li>100mm diameter</li><li>TPU filament (or similar)</li><li>Engineering plate (or similar smooth built plate)</li></ul>Small Drain Stopper Pad<ul><li>50mm diameter</li><li>TPU filament (or similar)</li><li>Engineering plate (or similar smooth built plate)</li></ul>&nbsp;Instructions for the Bathroom Sink Drain Stopper (Experimental)<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/159522/2023-10-11_8aa9334ebbc7a.png"></figure><ol><li>Insert 2 into 1. Try pushing the teeth of 2 together and then coming in at a top down angle into 1. Then slide the teeth down and when you reach the circle, lift the center of 2 to lock in place.</li><li>Slide 3 into 1 (on top of 2) while pushing down on 2's circle tab which will lock into 3's circle.</li><li>Slide in 4 on the opposite side.</li><li>Pinch 5 to get it around 6. Pull down one side of the ring (5) until it pops into place. This is best done on the wide sides of 6. Then do the same on the opposite side to fully pop in the ring (5).</li><li>Slide 6 sideways into the notch at the top of 2.</li></ol>&nbsp;My TPU SettingsI know this may help some people so I'm including the slicer settings I use for TPU.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/159522/2023-10-11_23495439f19ba.png"></figure>

Kitchen & Bathroom Sink Drain Strainers, Stoppers, Pads

Home

giamma933

If u want u can swap frame colour ( just swap again last layer )&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm&nbsp;Filaments Used:PLA BambuLab Basic Black Transmission Distance: 0.6PLA BambuLab Basic Blue Silk Transmission Distance: 2PLA BambuLab Basic Jade White Transmission Distance: 3.9PLA Overture Silk Gold Transmission Distance: 4&nbsp;Swap Instructions:Start with BlackAt layer #6 (0.56mm) swap to Blue SilkAt layer #7 (0.64mm) swap to Jade WhiteAt layer #16 (1.36mm) swap to Gold for the rest.&nbsp;If u want black frame u can swap the last layer to black

Black panther marvel hue forge final

hueforge

Harry Porpise

A toolbox case for the A1 and A1 Mini that replaces the old cardboard box. The only assembly needed is to snap the plastic tray into the container. I'm super happy with how this turned out, especially how clean the design on the lid is (taken from the old packaging).&nbsp;Update I: I tightened the fit of the lid.Update II: I slightly loosened the fit of the lid so it can be opened more easily.&nbsp;Happy printing!

Toolkit case for A1 + A1 Mini Accessories

a1 mods

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm&nbsp;Filaments Used:PLA BambuLab Basic Black Transmission Distance: 0.6PLA BambuLab Matte Scarlet Red Transmission Distance: 2PLA BambuLab Basic blue silk Transmission Distance: 3.5PLA BambuLab Basic Jade White Transmission Distance: 4&nbsp;Swap Instructions:Start with BlackAt layer #7 (0.64mm) swap to Scarlet RedAt layer #12 (1.04mm) swap to blue silAt layer #20 (1.68mm) swap to Jade White for the rest.&nbsp;

Spiderman hueforge painted final 

Decorations

Martin Kozak

Paw Patrol lookout tower with functional elevator, door and rotating monocular.&nbsp;Total height about 68 cm.&nbsp;You'll need some M2 and M3 screws and little bit of other hardware to put it together. See <a target="_blank" href="https://docs.google.com/presentation/d/1A9oc5LSpIfE7Vjarrvjy8W0-XEy0ydPLYvmmBd9ss7A/edit?usp=sharing" rel="nofollow noopener">BUILD GUIDE.</a>

Home

hueforge

a1 mods

Decorations

Toys