jamelb

Grant G

<h3>This is a super simple to print charging stand that utilizes your MagSafe charger. No supports required, and fully modular to fit your phone (as long as it has MagSafe).</h3><h3> </h3><h3>Update 8/5/23: Support for older style Apple Watch chargers!</h3><p>I have added models for the older style (non-fast charger) Apple Watch chargers, as well as the updated bases since the older chargers use USB-A connectors on the end. This means that you need to make sure you are using the correct pieces for your setup. I have put the new bases under the <strong>BASES</strong> folder and labeled them for the old chargers. I created new folders for the watch charger pieces and labeled the non fast chargers as REGULAR.</p><p>As a note, these pieces only work on the genuine Apple Watch chargers. Any third party charger will very likely not work.<br><br>Use this as a guide if you are unsure of which charger you have:</p><figure class="image image-style-align-center image_resized" style="width:71.2%;"><img src="https://makerworld.bblmw.com/makerworld/draft/442049/2024-01-23_l192ies20p7g.jpeg"></figure><p><br> </p><h3><strong>Bases:</strong></h3><p>There are 4 bases: A phone only base, a watch only base, and two combined bases. The difference between the two combined bases is that the compact version brings the watch and phone a little closer together. Only use the compact base if you have an iPhone 12 or 13 Mini. </p><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/442049/2024-01-23_bf2nyctg3j7u.jpeg"></figure><h3><strong>Other Pieces:</strong></h3><p>There are pieces for every phone that supports MagSafe, so make sure you are downloading the right piece! There are also tighter and looser tolerance versions of each piece (the tolerance has to do with the charger interface, not the interface with the base piece).</p><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/442049/2024-01-23_ng1a7at5mx4f.jpeg"></figure><p>There are also different pieces for the different sized watches. There are pieces for each size of watch, as well as the different types of chargers (fast charger or non fast charger).</p><figure class="image image_resized" style="width:55.46%;"><img src="https://makerworld.bblmw.com/makerworld/draft/442049/2024-01-23_bzq3ocklbcuw.jpeg"></figure><p>Print at 0.2mm layer height. Really only 2 perimeters are needed, but if you want more go right ahead. 15% infill does just fine and keeps filament usage down.</p><p>Lay all models flat, with the <strong>cable channels facing down</strong></p><p>If you are having trouble getting the phone or watch piece to fit in the base, try scaling the base up by 1%. This should help the pieces fit together easier. </p><p>Assembly video: </p><figure class="media"></figure>

MagSafe Charging Stand (Standby Mode)

Gadgets

CreatedByCreator

<p>Shop vac adapter for Ryobi corded miter saw. Designed to hook up to Rigid wet dry shop vac.</p>

Vacuum Adapter for Ryobi Corded Miter Saw

Tools

Blossom2023

Spider-Man 2099

Busts

MIHAI_T

<p>Foldable laptop support. Ideally for 13.1, 14 ‘’ displays.</p>

Aesthetic laptop support

Office

martin.taichl

<p>This is 3D printable model of the Defiant Class NX-74205 Defiant from the Star Trek. It is a kit. The different colored parts are separated for easier printing. <br><br><br>Pieces of some details need to be separated into separate models in the slicer ;) <br><br>In the suffix of the files, there are color codes:<br>g-grey<br>b-black<br>bl-blue<br>r-red<br><br><br>For the assembly, please have a look at the following video.<br> </p><figure class="media"><div data-oembed-url="https://youtu.be/BcMo-qCr9tE"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/BcMo-qCr9tE" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

Defiant - Defiant Class

Models

3djacobb

<p>Batman Helmet V2</p><p>&nbsp;</p><p>&nbsp;</p><p>Nice print :) </p>

Batman Helmet V2

Helmets

benlevi

<h2>BLV - AMS Riser for X1C V3.1 Final</h2><figure class="table"><table><tbody><tr><td style="background-color: hsl(0, 0%, 30%)"><h3><span style="color: hsl(0,0%,100%)">Introduction</span></h3></td></tr><tr><td><p>I&#39;m Ben Levi, and I want to talk to you about this BLV AMS Riser that I designed:<br>So, when the AMS is sitting on top of the printer, you can&#39;t really see what the printer is doing, and you can&#39;t even open the top glass cover to let some air in when you&#39;re printing High temp stuff. basically, something that will hold the AMS and free your Glass top cover will be a good solution for that. Now I&#39;ve seen some similar AMS risers before, but none of them really wowed me.. i think..</p><p>That&#39;s why I decided to come up with this sleek BLV AMS Riser design, easy to use, easy to put together, and reliable. I even added two handy drawers for your tools and stuff, a special shelf that can hold up to 4pcs Build Plates, built-in Dual LED strips. Sure, it took me a while, but I got it (almost..) done.</p><p>As some of you may know, I love contributing to this wonderful community, which is why I chose to share with you my project without any fee or money. Among other things, I&#39;ve also given you access to the original CAD files (F3D,STEP) so that you can easily make changes, add, and improve as you see fit. Please, if you publish a remix, make sure to link it to the original project as a remix so that others can benefit from your effort. I kindly request not to use the files for commercial purposes without explicit permission from me.</p><p>&nbsp;</p><p>Thanks,<br><strong>Ben Levi</strong></p><p><a target="_blank" href="https://www.paypal.com/paypalme/BenBLV" rel="nofollow noopener">If you want, buy me a beer </a>:)</p><p>&nbsp;</p></td></tr></tbody></table></figure><figure class="image image_resized" style="width: 58.95%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2023-09-25_370cc55ef0c1d.png"></figure><h2>Main features</h2><p>These are just a few design features I&#39;ve planned. If you have more ideas, please share them with me, and I can incorporate them into the design. Also, feel free to add remixes (CAD files are available for download).</p><ul><li>Easy installation</li><li>Dual LED strip<br>installed in optimal angle for LiDAR.</li><li>AMS riser</li><li>Top glass Holder</li><li>2 drawers for tools (with version for tools)</li><li>4 x Build Plates holder</li><li>Rubber Gasket for the glass</li><li>Customised Panels</li><li>access to original buttons</li><li>No screws required</li><li>CAD files available (F3D,STEP)</li></ul><figure class="table"><table><tbody><tr><td><p>&nbsp;</p><figure class="image image_resized" style="width: 92.39%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_18d41f48cf37f.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_a237ff37d0da5.png"></figure></td></tr></tbody></table></figure><h2> </h2><h2>How to print and where to begin?</h2><p>I must admit, if you&#39;re in search of a quick two-hour print and you&#39;re finished, this may not be the right place for it. To initiate and successfully complete this project, a considerable amount of filament and time investment is necessary. Here are the essential resources you&#39;ll be required to invest:</p><figure class="table" style="width: 70.13%"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><p style="text-align: center"><strong>Printing Time</strong></p></td><td>70~85 print hours - including color switching!</td></tr><tr><td><p style="text-align: center"><strong>Printer</strong></p></td><td>X1 Carbon, P1S, P1P, X1 or Other + AMS (Optional).</td></tr><tr><td><p style="text-align: center"><strong>Filament</strong></p></td><td><ul><li>2 kg - PLA/PETG Main filament color (GREY)</li><li>0.5 kg - PLA/PETG Secondary filament color (GREEN)</li><li>14 g - PLA/PETG Black filament for text (BLACK)</li><li>34 g - TPU flexible filament for your Gasket (BLACK)</li></ul><p>* Feel free to choose your own colors.</p></td></tr><tr><td colspan="2"><figure class="image image_resized" style="width: 98.07%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2023-10-04_77b29f1dbec36.jpg"></figure></td></tr></tbody></table></figure><p>I tried to keep the project in as few parts as possible and minimize the use of screws and glue. I&#39;ve also included three images that show all the parts and file names to help you easily know what to print and what to remove. <strong>Click on the pictures to enlarge.</strong></p><figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_5539d72c1e42.jpg"></figure></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_1698b67225759.jpg"></figure></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_34f66213cbfb2.jpg"></figure></td></tr></tbody></table></figure><p>&nbsp;</p><p>&nbsp;</p><h2>Printing settings</h2><p>Under each file name, I&#39;ve added a recommendation on how to print that component. Please note that these are just suggestions, and you can choose the filament type, infill percentage, and wall count according to your preferences.</p><p>Additionally, I&#39;ve attached an image below that illustrates how to orient each component on the print bed for optimal results <strong>(click to enlarge):</strong></p><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_c8a5b6a960393.jpg"></figure><p>Please note that you will find in also wonderful print profiles from the community too :)</p><h2> </h2><h2>Assembly instructions</h2><p>I think the best way to demonstrate the assembly is through a video. Therefore, I&#39;ve created a short animation video for you that illustrates the assembly process and the sequence of the project&#39;s components. Enjoy:</p><figure class="media"></figure><h3> </h3><figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_f7b5fb7649351.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_0604a5a98bf6d.png"></figure></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_4edcdff3d535e.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_f3764fb52c104.png"></figure></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_7b9abe53ec9f3.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_611a02308f5c5.png"></figure></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_d8d2275f63acd.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2024-05-03_f59c54b41a2bd.png"></figure></td></tr></tbody></table></figure><h3>Buttons assembly:</h3><p>Please print x2 Button insert.stl files and assemble as the photo below:</p><p><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2023-09-29_89172a00d321c.jpg"></p><p>&nbsp;</p><h2>Recommended Remix:</h2><ul><li><a target="_blank" href="https://makerworld.com/en/models/27690#profileId-24067" rel="nofollow noopener">Front Panels for P1P remix</a></li><li><a target="_blank" href="https://makerworld.com/en/models/28098#profileId-24385" rel="nofollow noopener">new Drawers with Clean look and version with Text</a></li><li><a target="_blank" href="https://makerworld.com/en/models/28948" rel="nofollow noopener">Spool Holder add on on the rear</a></li><li><a target="_blank" href="https://makerworld.com/en/models/29315" rel="nofollow noopener">Honeycomb panels for the sides</a></li></ul><h2>Links:</h2><ul><li><a target="_blank" href="https://s.click.aliexpress.com/e/_Dk1tOEL" rel="nofollow noopener">COB 5mm Dimmable LED strip</a> suitable to the project.<br>please make sure to choose: “white” and “Strip-USB Button” options.<br> </li></ul><h2>Colors ideas:</h2><figure class="image image_resized" style="width: 59.65%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2023-10-01_5f2218eae1ea7.jpg"></figure><h2>How to download CAD (f3d,Step) files:<br><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2023-10-03_16ad19d8f61ba.jpg"></h2><h2> </h2><h2>Selected User makes:</h2><figure class="table" style="width: 90.79%"><table class="ck-table-resized" style="border: 1px solid hsl(0, 0%, 100%)"><colgroup><col><col><col></colgroup><tbody><tr><td style="border: 1px solid hsl(0, 0%, 100%)"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2023-10-04_3aaa07d5a3c1e.png"><figcaption>click to enlarge</figcaption></figure></td><td style="border: 1px solid hsl(0, 0%, 100%)"><figure class="image image_resized" style="width: 86.34%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2023-10-03_f5f9b0b8d1086.jpg"><figcaption>click to enlarge</figcaption></figure></td><td style="border: 1px solid hsl(0, 0%, 100%)"><figure class="image image_resized" style="width: 100%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2023-10-03_ee05726581f83.jpg"><figcaption>click to enlarge</figcaption></figure></td></tr><tr><td style="border: 1px solid hsl(0, 0%, 100%)"><figure class="image image_resized" style="width: 100%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2023-10-01_8efeadcf004be.jpg"><figcaption>click to enlarge</figcaption></figure></td><td style="border: 1px solid hsl(0, 0%, 100%)"><figure class="image image_resized" style="width: 79.61%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2023-10-04_c0866329e4121.jpg"><figcaption>click to enlarge</figcaption></figure></td><td style="border: 1px solid hsl(0, 0%, 100%)"><figure class="image image_resized" style="width: 92.92%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2023-10-01_f106d497bd601.jpg"><figcaption>click to enlarge</figcaption></figure></td></tr><tr><td style="border: 1px solid hsl(0, 0%, 100%)" colspan="3"><figure class="image image_resized" style="width: 94.67%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2023-10-01_d8fbe88a9ea.jpg"><figcaption>click to enlarge</figcaption></figure></td></tr><tr><td style="border: 1px solid hsl(0, 0%, 100%)" colspan="3"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000019535/design/2023-10-01_0d0d9ff1ec084.jpg"><figcaption>click to enlarge</figcaption></figure></td></tr></tbody></table></figure><p>&nbsp;</p><figure class="table"><table><tbody><tr><td style="background-color: hsl(0, 0%, 60%)"><h2><span style="color: hsl(0,0%,100%)">Changelog</span></h2></td></tr><tr><td><ul><li>19/9/23 - published first prototype. not meant yet to print.</li><li>19/9/23 - uploaded v1.1 with angled glass holder and fixed Size drawer, stronger rear part.</li><li>23/09/23 - Left/Right/Rear Panel edges optimization for better surface finish.</li><li>24/9/23 - Huge update v1.2 !<ul><li>Extreme optimization to main parts, now it&#39;s 6 parts but much less support and faster to print.</li><li>Added wire channel for the LED&#39;s wires.</li><li>Added lock pins to TPU gasket.</li><li>new secure method to front and rear parts in addition to the dovetails.</li><li>Optimization to all decorative panels.</li><li>2 x Button frame cover with logo for P1P and P1S.</li><li>increased glass holder degrease to prevent movements.</li><li>Deeper AMS leg&#39;s socket, securing the AMS in it&#39;s place.</li><li>Added special drawer with accessories. it has a place for the H1.0-H2.0 HEX keys, 2 x Hotends, 5 cutters, 4 x wipers, screws, glue and needle.</li></ul></li><li>25/09/23 - updated new version 1.3 with measurements fix.</li><li>29/9/23 - added 2 remixes: clean front drawer, drawers with text, Dash front parts for P1P.</li><li>29/9/23 - added Button insert.stl + button images assembly.</li><li>30/9/23 - remix section update! spool holder, honeycomb panels added.</li><li>4/10/23 - New optimized slicing profile! faster, less filament, better support!</li><li>02/03/24 - added more support to side model.</li><li>04/04/24 - changed print profile for wider base.</li><li>22/05/24 - optimized structure for vibrations.</li><li>31/05/24 - changed Internal structure to be more rigid.<br> </li></ul></td></tr></tbody></table></figure>

BLV - AMS Riser for X1C / P1P / P1S V3.1 Final

Printer Mods

Rober7Crow

<p>I got the idea when I was making a headphone stand and a game board. I wanted to make a kind of whole, so that I could put everything together after playing. I played around with the designs a bit and came up with a stylish headphone and gamepad holder. <br>The PS 5 dualsense gamepad fits perfectly. <br>I printed with a Bambulab X1C + AMS for the multi-colour combination. Since my son liked it, I made him a V2 version in a different colour combination. <br>I hope you like the product and find it useful.</p><p>&nbsp;</p><p><strong>Update: Corrected top Z distance to 0.2 because it is too hard to remove support </strong></p><p>&nbsp;</p><p><strong><u>REMOVE THE SUPPORT GENTLY, USING PLIERS. </u></strong></p><p>&nbsp;</p><p>3D PRINTING SETTINGS<br>layer height 0.2 mm<br>wall loops 3<br>15% Gyroid fill<br>Hybrid support tree on the build plate only</p><p>&nbsp;</p><p><strong>My new addition to the collection is a game stand  </strong></p><p><a target="_blank" href="https://makerworld.com/en/u/2142032364" rel="nofollow noopener">Rober7Crow | Published - MakerWorld</a></p><p>&nbsp;</p><p><a target="_blank" href="https://makerworld.com/en/models/168868#profileId-185466" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/512845/2024-02-03_4a4841357f6fe.png"></a></p>