houndzilla

3DG Designs

Ford Shelby Logo for use with AMS system, this was printed on a textured pla plate at 0.16mm layer height. Ironing was set to topmost surfaces, it comes out flawless as long as your printer is dialed in, no signs of any lines. Can resize any which way you like or switch the colors!&nbsp;Perfect Garage/Office decor or anywhere.&nbsp;Colors used:&nbsp;Polymaker Charcoal BlackPolymaker Cotton WhitePolymaker Lava Red

Ford Shelby Logo Multi Color

print profiles

Chester3D

Solid and stylish stand to keep the plates of your Bambu P1S / X1C / X1C / P1P organized and easy to access!&nbsp;Allows up to 4 plates, whether textured, engineering, or cool plate. Each plate is located at a different height in this stand, so you can access each one regardless of its position.&nbsp;This is a quick and easy print. No supports, no brim, no overhangs! <a target="_blank" href="https://emojipedia.org/shopping-cart" rel="nofollow noopener">🛒 </a><a target="_blank" href="https://eu.store.bambulab.com/products/bambu-textured-pei-plate" rel="nofollow noopener">Textured PEI recommended</a>. <a target="_blank" href="https://emojipedia.org/star" rel="nofollow noopener">⭐</a>Easy installation: Lift the printer slightly on one side and insert the piece from bottom to top. Find the right position by sliding this printed stand forward or backward until you see that it fits perfectly. &nbsp;If you like it and found it useful, I appreciate your comment sharing a photo of your printer with this printed model! You will make me very happy (and if you leave a like, even more 😊😊).&nbsp;Remixes allowed!&nbsp;&nbsp;<h3>-------------- Another MUST HAVE mods: <a target="_blank" href="https://makerworld.com/en/models/57491#profileId-59222" rel="nofollow noopener">Top Glass Riser P1P / P1S / X1C / X1E</a> <a target="_blank" href="https://makerworld.com/en/models/57491#profileId-59222" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/209834/2023-11-05_b8afa77a54ccf.jpg"></a></h3>&nbsp;<h2><a target="_blank" href="https://makerworld.com/en/models/75722" rel="nofollow noopener">PTFE Toolhead Clip</a> (<a target="_blank" href="https://makerworld.com/en/models/75722" rel="nofollow noopener">AMS Unload Fix</a>)</h2><figure class="image"><a href="https://makerworld.com/en/models/75722" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/209834/2023-11-27_82ead541ec742.webp"></a></figure>

Plate Holder for Bambu P1P P1S X1 X1C X1E Cool Textured Engineering

printer accessories

HG_Design

Stacking boxes.Boxes can be printed to the desired scale and make a perfect fit in any location.leave suggestions for improvement and new ideas to leave here.&nbsp;

Stacking box

utilitarian 

TS.Makers

Top your christmas tree with style with this Super Mario Xmas tree topper. The model comes with a slot to slot in a Xmas tree LED to light it up though may not be effective depending on your choice of filament. Please read the following considerations when printing with my profile. &nbsp;The tree topper coil prints like a solid blob with my pre loaded support settings. The coil is actually flexible and supports can be released by gently bending the coil and pulling off the support with pliers. Glue is highly recommended when printing the star. The eyes are pressure fit and do not require glue as long as your printer is well calibrated. Needle nose pliers are the only tool needed for this model. Assemble by threading the coil into the bottom of the star. &nbsp;I dont own an Xmas tree but I tested the coil on an Elf tree. If the coil is too short add a little bit of heat via blow dryer or hot watter while attacked to the star and streach out the coil. If you find this is insufficient feel free to PM me a length of coil you need and I'll see what I can do.

print profiles

printer accessories

utilitarian

fun stuff