high99

<boostme><boosttitle>Boost Me</boosttitle><boostcontent>Help support the creation of great models by clicking Boost! </boostcontent></boostme>I needed an adaptor connect the outlet of a washing machine and tumble dryer to a single drain. The ones at the hardware store didn&#39;t match my pipe fittings and were nearly £20!. Printed one in PLA using 17g of filament.&nbsp;<ul><li>top opening - 23mm inner diameter. 25mm outer diameter.</li><li>small opening - 13.5mm inner diameter. 15.5mm inner diameter.</li><li>bottom opening - 27mm inner diameter. 29mm outer diameter.</li></ul>Measure your own drain pipe and hoses to ensure a proper fit. Fusion360 .3mf file included to allow modification of sketch geometry.&nbsp;

Y-Connector for Washing machine and Tumble Dryer

My Uploads

GekoPrime

I tried another spool winder but found it finicky and delicate.I designed this winder from scratch to be simple and robust, using the same self reversing leadscrew mechanism found on industrial cable windersWhy pick this model:<ul><li>Prints on a single build plate</li><li>Doesn't require heat set inserts or exotic hardware</li><li>Fusion and STEP files are available, remixes welcomed</li><li>Generous clearances, simple mechanisms</li><li>Designed to be a tool, not a project</li></ul>Print time:<ul><li>~500 grams of filament</li><li>~22 hours on Bambu Lab X1</li><li>~5 minute assembly</li><li>~2 minute spool transfer</li></ul>Hardware requirements:<ul><li><a target="_blank" href="https://www.amazon.com/s?k=608+bearings" rel="nofollow noopener">14x 608 skate bearings</a></li><li>A scrap of PTFE tubing</li><li>An electric screwdriver or drill with <a target="_blank" href="https://www.homedepot.com/p/DEWALT-MAXFIT-3-5-in-2-Philips-Bit-DWA3PH2MF/309474882" rel="nofollow noopener">a bit cut from ¼ inch hex stock</a> (most <a target="_blank" href="https://www.amazon.com/ITP1201-SCRWDRVNG-2IN-1-IMPAC/dp/B01LZZ7AOS/" rel="nofollow noopener">cheap quick change Philips bits</a> in the US fit this requirement)</li></ul>Print settings:<ul><li>Any. I used "0.16mm Optimal" in BambuSlicer with 5% adaptive cubic infill </li><li>Use 100% concentric infill for spindle_male_driven</li><li>Try the STLs if you have a problem with the 3mf files. I’ve added (xN) to each file name so you know how many to print</li></ul>Materials:<ul><li>Any. I used Polyterra and iiidmax PLA+</li><li>Use TPU for tpu_consumable_wiper_blade. I used Priline 98a. The wiper blades aren’t 100% required but they help keep the windings nice and tight</li></ul>Assembly and usage:<ul><li><a target="_blank" href="https://youtu.be/DxgkYDrRK-U" rel="nofollow noopener">Demo video</a></li><li><a target="_blank" href="https://youtu.be/-Hy69YwRLBw" rel="nofollow noopener">Assembly video</a></li><li>The side that says “Pastamatic" needs to face outwards, away from the spool</li><li>The filament needs to come in under the target spool, like this: O____O<ul><li>[not like this: O‾”‾”‾”O]</li></ul></li><li>The drill/driver needs to run clockwise, as though you're screwing something in</li><li>Accelerate slowly until the winder gets started</li></ul>Change log<ul><li>2023-05-28<ul><li>Initial release</li></ul></li><li>2023-05-29<ul><li>Fix a minor export glitch in "leadscrew_tooth"</li><li>Increase the number of “pin_short” instances in the 3mf from 6x to 8x</li></ul></li><li>2023-05-30<ul><li>Add a second prearranged 3mf with two plates to avoid overlap warnings</li><li>Disable autogenerated brims for the single plate 3mf </li><li>Add STLs for people who have trouble with the 3mf</li></ul></li><li>2023-06-03<ul><li>Add a ring to passive_target_cradle to prevent the far end of the target spool lifting if a user lets the the drill hang loose</li><li>Add a pin to driven_target_cradle prevent the leadscrew popping out</li><li>Fix a minor clearance issue where a dovetail didn't fit quite right</li></ul></li><li>2023-09-30<ul><li>Reduce chamfer on the crossbars to prevent them falling over when bed adhesion is poor</li><li>Add some holes to the crossbars to make them easier to screw down</li><li>Add some popular acessories to the all-in-one .3mf</li><li>Add a printable spool to the all-in-one .3mf</li></ul></li></ul>How to contribute:<ul><li>Post your make, it keeps me motivated to improve the model when I see people using it!</li><li>Post your feedback, idea or remix in the comments!</li><li>There are a few improvements and accessories in development as remixes, check those out if you‘re up for the alpha/beta tester experience<ul><li><a target="_blank" href="https://www.printables.com/model/498743-pastamatic-37-mm-motor-mount" rel="nofollow noopener">Adapter for 37mm gear motor</a></li><li><a target="_blank" href="https://www.printables.com/model/556405-pastamatic-filament-spool-winder-modifications-bra" rel="nofollow noopener">Source spool holder for 5 KG spools</a></li></ul></li></ul>Credits:<ul><li><a target="_blank" href="https://www.printables.com/@MiklosKiszely_486882" rel="nofollow noopener">@MiklosKiszely_486882</a> for the original idea</li><li><a target="_blank" href="https://www.printables.com/@PsychoShaft_33891" rel="nofollow noopener">@Psycho Shaft</a> for the drag/tensioner concept</li><li><a target="_blank" href="https://www.youtube.com/@thang010146" rel="nofollow noopener">thang010146</a> for YouTube videos of mechanical mechanisms, particularly the self reversing leadscrew for a level cable winder</li></ul>&nbsp;

Pastamatic  Filament Spool Winder for Bambu X1C/P1P AMS (level winder with self reversing leadscrew)

Printer

Chewmieser

Gridfinity bins for a 21-piece Dewalt imperial drill bit set. This set fits within a 4x3 gridfinity grid and was originally intended for use in a Kobalt Mini Toolbox (fits all sections; bins are 3u in height).&nbsp;Would suggest printing with a &lt; .6mm nozzle, otherwise the text on the smaller bins wont come out properly (see cover photo).&nbsp;Bin blanks created using the GridfinityGenerator Fusion 360 add-in.

Gridfinity 21-Piece Imperial Drill Bit Holders 

Gridfinity

tlisek

A simple allen key holder for multiboard. Sizes: 10, 8, 6, 5, 4, 3, 2.5, 2, 1.5 mm.&nbsp;Comes in two versions: with engraved (debossed) and embossed textAttaches using <a target="_blank" href="https://www.printables.com/model/790060-anti-rotate-multiconnect" rel="nofollow noopener">anti-rotate multiconnect</a> (included in the plates) so you can quickly remove it from the multiboard and take it with you

Removable Multiboard Allen / Hex Key Holder 

Multiboard

rostap

<h3>Arm mounting system </h3>It is a universal set of holders and arms. You can use this system as a notebook holder, tablet holder, monitor holder, camera or any other device holder or you can have it as a shelf holder.If you print a pair, you can made various tables.You can attach more arms togehter. I made some connecting parts and other accessories. There are no limits to imagination. I made it with increased strength and durability. If you add few perimeters the holders/arms can hold pretty good weight. &nbsp;&nbsp;&nbsp;Small light versionHolders reduced x 0.6 and then adjusted (hole sizes, gaps, etc.)<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_ygt4l1gyz0rx.jpg"></figure><h4>Základní informace</h4><figure class="table"><table><tbody><tr><td>&nbsp;<figure class="image image_resized image-style-align-left" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_1vuk35qftkm3.jpg"></figure>&nbsp;</td><td>&nbsp;You can adjust the angle in ten degrees. Screw and nut fit on both sides. &nbsp;&nbsp;&nbsp;</td></tr><tr><td>You can tight and loose from both sides no matter where the nut is. </td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_5bbkp2ve4kgr.jpg"></figure></td></tr><tr><td><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_l4f3cs4r4hsf.jpg"></figure></td><td>There are various nuts and screws. Of of them counts with the allen screw (hex bolt) M8x40&nbsp;</td></tr><tr><td>You can also print the crew which can be tight and loose without gear- with the printed hex bolt screw. </td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_7dyjbvq16pqm.jpg"></figure></td></tr><tr><td><img src="https://media.printables.com/media/prints/165239/rich_content/5d2096ce-0223-4834-ade9-1fd6b3aec194/resize_img_6432.jpg#%7B%22uuid%22%3A%2292583698-0623-4e34-94da-bb853c30ae47%22%2C%22w%22%3A2016%2C%22h%22%3A1512%7D"> <img src="https://media.printables.com/media/prints/165239/rich_content/4dd49cb0-b7a2-4690-8a96-9c03407d2c2e/resize_img_6427.jpg#%7B%22uuid%22%3A%225c571a00-83c6-45bf-a6bb-97f04a44ed33%22%2C%22w%22%3A2016%2C%22h%22%3A1512%7D"></td><td>The holes for key in the screw and two arms have the same size as the holders in Honeycomb storage wall (https://www.printables.com/cs/model/152592-honeycomb-storage-wall). That means that you can hang different accessories on the arms. </td></tr><tr><td>There are various of arms. </td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_bdrw6oh1oh1y.png"></figure></td></tr><tr><td><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_u06b8t58ztlv.jpg"></figure></td><td>ClampI made 3 different types - <ol><li>for the screw M5/M6 mounting spacing for holders 30x30mm</li><li>for the screw M5/M6 mounting spacing for holders 40x40mm</li><li>for the screw M5 mounting spacing for holders 40x40mm</li></ol>&nbsp;</td></tr><tr><td><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_t3u1ipn1agdd.jpg"></figure></td><td>VESA rotating holder - 75mm</td></tr><tr><td>Combination for possitioning along the axis Z<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_7m1sfrwcw20k.jpg"></figure>&nbsp;&nbsp;</td><td>System - high table for tablet holder <img src="https://media.printables.com/media/prints/165239/rich_content/228c6e5e-a2a4-41ce-a79e-962f4006c973/resize_img_6430.jpg#%7B%22uuid%22%3A%22da81a7de-4dd3-453e-96dc-6c179e6bc32e%22%2C%22w%22%3A1512%2C%22h%22%3A2016%7D"></td></tr><tr><td><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_11nh0grq3czm.jpg"></figure></td><td>There are holders for three tablets. Bottom width<ol><li>196 mm</li><li>250 mm</li><li>305 mm</li></ol>screw spacing 30mm</td></tr></tbody></table></figure><h4>Basic arms</h4>The only difference is the grid<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_0qsfmal86eys.png"></figure>&nbsp;<h3>Holders</h3>A few basic handles<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_wjg38olir4sz.png"></figure>&nbsp;<h4> </h4><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_ej2zf1avpe73.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_2ujybj6hyhzb.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_3i0br0eesaay.png"></figure>&nbsp;I printed small parts on the Prusa Mini, the arms on the Ender 3.&nbsp;My printing settings<ul><li>material: PETG</li><li>perimeters: 8 and more</li><li>infill : 30% and more</li><li>layer height 0.3 (with nozzle 0.6 layer height 0.4) (screw and nuts only 0.2mm layer height) </li></ul>&nbsp;

Multifunction Arm mounting system

Home

hexacontaphilie

I put every letter in a different file so you can arrange it on you print bed. You can scale the parts but don't scale all the axis the same otherwise the tickness will change.If you want the first layer as the visible layer, don't forget to horizontally flip the parts in you slicer.You can fix it on a wall with double-faced tape.

Porsche logo silhouette wall decoration

Milhaus

3 COPY TOOL sizes (small, medium, large) All variants include a screw for tightening/remembering the shape. - Variant S - requires printing 32 copy strips. Outer body dimension is 50mm, inner 34mm. - Variant M - requires printing 47 copy strips. Outer body dimension is 66mm, inner 50mm. - Variant L - requires printing 94 copy strips. Outer body dimension is 116mm, inner 100mm.&nbsp;I recommend to glue the body, part A + B with instant glue.&nbsp;I hope you find this COPYING TOOL helpful.

Contour Gauge (COPY tool)

Tools

MakerVerse Designs

Fully 3d printed crocs shoes<ul><li>Printed with Overture TPU</li><li>PLA for the snap button</li></ul>Important notes:<ul><li>It is for EU shoe size number 42 (male), but you can scale every part (CrocsL1,CrocsR1,Holder,Mount1,Mount2) to your size (use uniform scaling)</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425034/design/2024-04-19_0266f756a989a.png"></figure><ul><li>If the shoe is too big to fit to the printers height, use the “WithSupport”-Version, rotate in Y-Axis (green) and use the cut tool in Bambu Studio to create a new flat surface parallel to the print bed<ul><li>I uploaded an .stl file without cut on the bottom for better scaling</li></ul></li></ul>&nbsp;<ul><li>There are two ways to print this:</li></ul><ol><li>Use a textured PEI bed and print it standing up without support</li><li>Or use another not so sticky bed and print it standing up with support</li></ol><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425034/design/2024-04-12_cc0523cbae068.png">&nbsp;If you can&#39;t get enough of printed shoes, check out my new model (Slide Shoes, Adilette):<a target="_blank" href="https://makerworld.com/en/models/488792#profileId-401842" rel="nofollow noopener">https://makerworld.com/en/models/488792#profileId-401842</a><img class="image_resized" style="width: 41.76%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425034/design/2024-06-08_bb258037ea2a1.png">Have fun with it and leave a like or subscribe if you like it!If there are any suggestions for improvement, feel free to write a comment.