heyderekp

DKprints

Recycle your AMS waste and turn it into insulation! This enclosure designed specifically for the A1 Mini WITH AMS insulates the printer from outside elements leading to less warping and variability in temperature. This uses a ton of purged filament and support material as insulation in modular sections that can be stacked higher or lower depending on the height or setup of your printer. The files included are specific to the A1 Mini, but can be scaled to fit your printer if need be. Most of the pieces slot together with the exception of the front door and lid, which need to be glued and include holes for aligning utilizing short filament sections as pins. All parts can be printed on the A1 Mini, but to save time, if you have multiple printers, I&#39;ve included X1C/A1/P1 series files as well. The stock PTFE tubing is a bit too short, so it will need to be extended in order to use this enclosure. Note that it is NOT manufacturer recommended to enclose the A1 series printers. &nbsp;You&#39;ll Need:¼ or 6mm Wooden Dowel Rod/Threaded Rod/Solid Rod cut to around 17.5in or 444mm - I used <a target="_blank" href="https://a.co/d/cCsl0Qw)" rel="nofollow noopener">https://a.co/d/cCsl0Qw</a>11x14 Acrylic Sheet - I used a cheap picture frame and then took out the pre-cut acrylic <a target="_blank" href="https://a.co/d/fW9RtZk)" rel="nofollow noopener">https://a.co/d/fW9RtZk</a>PTFE Tubing - <a target="_blank" href="https://a.co/d/dQ6dqUf" rel="nofollow noopener">https://a.co/d/dQ6dqUf</a>Super Glue2mm or 5/64in Drill bit (optional) - <a target="_blank" href="https://a.co/d/hxv6ECD" rel="nofollow noopener">https://a.co/d/hxv6ECD</a>&nbsp;To Assemble: <ol><li>Slot straight wall piece with large passthrough hole for wall plug into both corner pieces. Then slot straight wall piece with small passthrough for AMS on the right of the machine. Slot straight wall piece into other side and then the two semi-circle corners onto the ends of the two straight pieces. </li><li>Connect the two small support pieces together by aligning both dovetail joints together and then slot on to the ends of the semi-circle pieces. </li><li>You&#39;ve now completed the first row of the enclosure and have a square surrounding your printer!</li><li>Now it&#39;s time to get rid of your filament waste and fill each wall section. </li><li>Repeat for both remaing rows with more wall sections. Note that there shouldn&#39;t be any walls with hole passthroughs on the top two rows. </li><li>Once the enclosure is three rows high, slot in hinge pieces taking note to make sure the hinge pattern is alternating and the smallest of the hinge pieces is at the bottom with the smallest gap at the bottom as one of the hinge sections is shorter than the rest. </li><li>Slot in the door stop pieces with the larger side on the inside of the enclosure. This is what the door rests against when closed. </li><li>Glue together door pieces taking caution to make sure all the pieces are flush and door handle is pointed outward. </li><li>Glue in acrylic window and install door using dowel rods through the hinges.</li><li>Assemble the top using optional filament pin holes. Some of the holes will need to be drilled out with the small drill bit and then small sections of filament can be used to align the two sides together before gluing. The dovetail joint pieces can then be glued as well. </li><li>Set the top onto the walls making sure the blank underside is over the door.</li><li>Extend the PTFE tubing to AMS as the factory included tubing is a bit too short. </li></ol>

Insulated A1 Mini Enclosure

a1 mini

itssunnyb

Dual Wire Cutter/Plier Holder for the Multiboard-Added a single cutter/plier option&nbsp;Multiboard https://www.multiboard.io&nbsp;Print settings:<ul><li>Material PLA+</li><li>Layer Height 0.2</li><li>Perimeters 4</li><li>Infill 15%</li><li>No supports</li></ul>

Single/Dual Wire Cutter/Plier Holder for the Multiboard

multiboard

Modular Mapping

With this brackets you can attach pieces of 19mm or 18mm wood to each other to build a shelf.Once mounted the shelf also is pretty stable and can take quite some load.Printable without support.Use Infill over 20 % to ensure that the parts are strong enough.If you need a different wood thickness, hit me up ;)

Angled Shelf Connectors

cats

JamesThePrinter

*This project requires one 608 bearing*There is a printable spring that adds a slight clicking sound when the carousel is spun. This is recommended, but optional.As with any assembly that prints in multiple pieces and/or uses other components, actual clearances will be dependent on YOUR printer.&nbsp;<figure class="media"><oembed url="https://www.youtube.com/shorts/D3xfdgBf4jE"></oembed></figure>Print SettingsThe Nintendo Switch logo in the middle of the carousel is designed to give you two options:<ul><li>If you have an AMS, MMU or similar product, the logo can be easily painted in the slicer</li><li>If you do not paint it in the slicer, the logo will not appear at all</li></ul>&nbsp;Assembly Instructions<ol><li>Insert a 608 bearing into the center of the base</li><li>If you are using a spring, use a very small amount of glue to secure it into the hole as shown below</li><li>Place the carousel on top of the base, ensuring that the gear tip drops into the center of the bearing</li></ol><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000014299/design/2023-09-12_pikoqdkmfdj3.png"></figure> <a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The filaments used in the pictures above:<ul><li>Bambu Lab Red Matte Scarlet Red PLA</li><li>Bambu Lab Matte Charcoal PLA</li><li>Bambu Lab Matte Ivory White PLA</li></ul>

Nintendo Switch Game Carousel

Gaming

k2thestank

Easy to print and fun to have!Features a slide and lock in Design to hold the Docking station tighter and prevents it from sliding or popping out as easy!<ul><li>You can split the STL's into parts for easier coloring as well if your not using the 3mf file as i have pre-split them in Fusion</li></ul>&nbsp;Stores 12 Game Cartridgestakes approx. 180gramsMaterials: - Crazy GluePrint Settings: - Walls: 3 - Top/Bottom Layers: 4 - Infill: 10% Gyroid Revisions: - Increased size of block for extra game slots and to improve its look- Fixed missing pieces and corrected files that didnt export correctly

Mario Switch Dock - Original System

Office

LucMeister

Keeping small screws and other bits&pieces tidy and organized is a tedious task, and even though lots of them ship in plastic boxes it's a pain when they have thirteen different sizes and just stack very badly. I see a lot of recommendations (and printable accessories) for <a target="_blank" href="https://amzn.to/3tDQ1bK" rel="nofollow noopener">Stanley Fatmax organizer boxes</a> - they look dope and I dig them, but a single box of these costs roughly 25€ in my location; printed inserts not included. That's a bit of a hefty price if you need a few of them.&nbsp;history. Last year <a target="_blank" href="https://www.printables.com/model/380208-dividers-for-werckmann-storage-boxes" rel="nofollow noopener">I saw a model on Printables</a> which used super cheap (99 Cents!) <a target="_blank" href="https://www.action.com/de-at/p/2547795/werckmann-aufbewahrungsbox/" rel="nofollow noopener">storage boxes/organizers from the ACTION Store Chain</a> across Europe (originally from the Netherlands); these sometimes go under the Werckmann brand name and sometimes are only generic (see image), the inner layout is the same though; just make sure it's the 20 x 16 cm version. Those models were a bit wasteful and too thick (and therefore printed slowly) in my opinion, so I gave the idea a spin and designed them myself. boxes. The outer walls are thin as they are carried by the organizer box itself, the inner dividers are three walls thick (0.4mm nozzle) which is plenty strong for the application. The bottoms are chamfered to get things out easier, but as you can see on the photos the bottom is chamfered as well to save a lot of filament and printing time.There's a total of 36 different boxes and layouts, there's a lot of ways you can divide these :) some of the corner-pieces are also available in different orientations so you can direction-match an upper and a lower corner, see the photos for examples. I also added boxes without dividers, in case you want to look-match other compartments or just want the chamfered bottom. As naming these are hard with all the different divisions, I only wrote the total number of compartments and labelled them ABC, please have a look on the exact differences on the STL files.&nbsp;I also made a shelf specifically for these boxes (see photos), <a target="_blank" href="https://makerworld.com/models/134601" rel="nofollow noopener">you can find it here</a>.The specialized inlay for TS-100 tips from CNCKitchen <a target="_blank" href="https://makerworld.com/models/136915" rel="nofollow noopener">can be found here</a>. printing advice. The provided printing profile contains the settings I recommend for printing (0.28mm because they really don't need to be any finer), but it's just sample files; it's virtually impossible to provide all combinations you might want, so please fill the slicer with the exact models you need :)Depending on the pieces you want to print, one fully assembled organizer box will need 65g to 108g of Filament, which translates to 1.30€ to 2.16€ at a Filament price of 20€/kg. So for roughly 3€, you have a fully equipped organizer! If you don't care as much about looks, it's also a good way to get rid of nearly empty spools of filament, as you can see in the orange-green example in my photos :)

Werckmann / ACTION Organizer Box Inlays

Organization

Chaosdrucker

Zur ändern der Originalen Box um diese in der Lieblingsfarbe zu Drucken.<h3> Print Settings</h3>Printer:AnycubicRafts: <div>No</div>Supports:NoResolution: <div>0.2</div>Category: 3D Printer Parts

Ender3 PSU Cover Box

ender3

mike.pasquariello

Here is my version of the famous “Floating Cup” model. You can see that mine has a hidden Mickey in the coffee splash! &nbsp;This model is designed to use washers to weigh down the splash. They should be 2" OD and ½" ID like these: https://a.co/d/cGHOK2I&nbsp;There is a file of trapezoidal pins scaled to a range of sizes, used to attach the "splash" to the "stream" and keep them aligned. Choose the largest one that fits into the sockets in the "stream" and "splash" parts. Trimming their edges with a knife or clipper, or sanding them down may be required.&nbsp;Thank you to <a target="_blank" href="https://www.printables.com/@bwaslo_1772" rel="nofollow noopener">@bwaslo_1772</a> for remixing the original model by HappyMoon.

Spilling Coffee (Floating Cup) With Hidden Mickey!

Just Cool Stuf

Filamently

A modular organizer with tray caddy offers an elegant, easy-to-print solution to your desk tidiness woes!<ul><li>Simple design reduces waste – print and swap blocks when you need more storage</li><li>Modular components set in place using the “+” symbols as a guide</li><li>Blocks use 2.4mm walls to facilitate faster printing with good durability</li><li>Hundreds of combinations with 5 tray sizes and 20+ modular blocks</li></ul><h3>Tolerances</h3><ul><li>0.2mm between blocks</li><li>0.4mm on bottom surfaces that require bridging</li></ul><h3>Printing Recommendations</h3>Optimized for 0.2mm layer height. Please be aware that extreme warping on tray pieces will cause fit issues.&nbsp;If not using the included profile or 3MF, recommend the following settings:<ul><li>Strength > Bridge direction = 45°</li><li>Speed > Overhang speed > "25, 50%" = 30mm/s</li></ul><h3>Includes:</h3><ul><li>5 tray sizes: 2x2, 3x2, 3x4, 4x2, 4x3</li><li>1x1 blocks<ul><li>1x1 short</li><li>1x1 short stackable</li><li>1x1 medium</li><li>1x1 tall</li></ul></li><li>2x1 blocks<ul><li>2x1 short</li><li>2x1 medium</li><li>2x1 tall</li><li>2x1 tall (½ divider)</li><li>2x1 tall (⅓ divider)</li></ul></li><li>2x2 blocks<ul><li>2x2 short</li><li>2x2 medium</li><li>2x2 medium tiered (w/ insert)</li><li>2x2 phone stand (+ w/cable slot)</li></ul></li><li>3x1 blocks<ul><li>3x1 pen/pencil tray (18mm tall)</li><li>3x1 phone stand (28mm tall)</li><li>3x1 short</li><li>3x1 medium</li><li>3x1 tall</li><li>3x1 tall w/hex pattern</li><li>3x1 tall no sides</li></ul></li><li>4x1 blocks<ul><li>4x1 short</li><li>4x1 short w/dividers</li><li>4x1 medium</li><li>4x1 notebook storage</li></ul></li></ul>&nbsp;Please send me a note with any suggestions or if you experience issues with printing any models.&nbsp;Thanks! :)&nbsp;

Modular Desk Organizer

Office Desk

John Hoke

Remixed the original author's step files in Fusion adding Sony Alpha logos for multicolor printing. The original versions required printing two separate objects and gluing together, this way they are merged as a single object with multiple bodies for the cap and grip, as well as two components for the “SONY” and “alpha” logos.&nbsp;For printing, I used 3 walls, 10% gyroid infill, Arachne wall generator and 2.1mm min bottom layer in the slicer. Filaments used :<ul><li>IIIDMax <a target="_blank" href="https://iiidmax.com/product/xtreme-black-pla-filament-w-nanodiamonds/?ref=ujpx3DsHAal8c_" rel="nofollow noopener">Black Xtreme PLA+</a></li><li>Bambu Labs White Basic PLA</li><li>Bambu Labs Orange Basic PLA</li></ul>If you print it please like and post a make ❤️

Sony Alpha Body Cap - 3 color with logo - No Glue

photography

The Crafty Maker

"They're the most heavily armored ground vehicles in the Imperial Army." "...so what you're saying is that you have a thorough knowledge of just how screwed we are."Introducing the newest member of the springie Star Wars series, the massive AT-AT springie. One of the most feared weapons in the Star Wars franchise made into a bobble toy.&nbsp;<a href="https://www.youtube.com/shorts/Xwn5s7uAGuA" rel="nofollow">https://www.youtube.com/shorts/Xwn5s7uAGuA</a>&nbsp;The used spring is designed by <a href="https://www.printables.com/social/106529-3d-printy/about" rel="nofollow">3D Printy</a> (<a href="https://www.printables.com/model/282561-parametric-bobblehead-springs" rel="nofollow">Parametric Bobblehead Springs</a>)Supports needed for most parts. STL files are oriented for optimal printing.See photos for assembly.&nbsp;ALL The Crafty Maker designs are protected by Copyright Law. By downloading, YOU HAVE NO RIGHT to sell any digital files or reproductions from those files. If you want a commercial license to LEGALLY SELL 3D prints, you'll need a <a href="https://patreon.com/TheCraftyMaker" rel="nofollow">The Crafty Seller Patreon</a> subscription.

Star Wars AT-AT Springie

star wars

Marc Elbichon

This remix add a back plate to prevent the battery to slide on the wall/panel. Also reduce thickness of the mount to a more tight fitCategory: Tool Holders & Boxes

Ego Battery Wall Mount

Eminent3D

Wall mount for Ryobi Impact Driver

Ryobi Impact Driver Mount

Ryobi

Tazzy1992

Printed in PLA, increased the infull by 10% to give it a bit more stability

Lego Porche 911 RSR Wall Mount

Lego

Raka Prints

This is my take on the 3D calendar of the 2024 season of Formula 1.&nbsp;Everything is facedown for the Textured PEI sheet finish.Flags are printed on photo paper not normal paper so it shines more. You can find them in the pdf file.If you need the text/word file message me and I will send it to you.&nbsp;If you want to support me you can always buy me a coffee - <a target="_blank" href="https://www.buymeacoffee.com/rakaprint3d" rel="nofollow noopener">https://www.buymeacoffee.com/rakaprint3d</a> -Or use my eSun affiliate link or use my code “RAKAPRINTS” for 10% off.Aff. link: <a target="_blank" href="https://esun3dstore.com/?ref=RaKaPrints" rel="nofollow noopener">https://esun3dstore.com/?ref=RaKaPrints</a>&nbsp;Materials needed:Esun PLA+ Black, Red and WhiteFoam board (700mm x 1000mm)Double-sided tapeSuper glue&nbsp;&nbsp;Update:02/01/2023: Curb connectors Layout (PDF) added03/01/2023: Shangai changed to Shanghai04/01/2023: Added F1 template for glueing the track, flag, land and city.16/01/2024: Dates added (new print profile).13/02/2024: Added a new template for Country, city and date.

F1 Calendar - 2024

auto

Encrust3d

This is a tool to help lube the Z axis lead screws for the Bambu A1 printer. I designed this tool to be able to fit inside the slots on the Z axis of the A1 printer and, when you are done spreading the lube, you can rest this tool down on a flat surface without that surface getting grease on it. The spreader is angled so you can spread at an angle like the video shows.

A1 Lube Helper with Kickstand

I've designed this toy ratchet/socket wrench for my 7y old son.The driver use a print in place friction spring that simulates the distinct clicking sound and feel of a real ratchet wrench. 6 different socket sizes are provided. The sockets click in place by a 2nd friction spring on the driver's socket interface.The back assembly of the driver should friction fit but can be glued into the front assembly of the driver.All parts should be printed using supports.&nbsp;ALL The Crafty Maker designs are protected by Copyright Law. By downloading, YOU HAVE NO RIGHT to sell any digital files or reproductions from those files. If you want a commercial license to LEGALLY SELL 3D prints, you'll need a <a href="https://patreon.com/TheCraftyMaker" rel="nofollow">The Crafty Seller Patreon</a> subscription.

Toy Ratchet/Socket Wrench

toys

matt.pongratz

I wanted a wallhanger to hang my Ryobi jig saw. As I couldn't find one I designed one myself. Printed it with Bambulab PLA with 0.2 layerheight, 25% Infill and 3 walls.

Wallmount for Ryobi Jigsaw / Wandhalterung Ryobi Stichsäge

diy/tools

buckler-bronze

ModelDifferent diameter nets/mesh that can be printed and added to the bottom of a planter so the soil doesn't get washed out when watered.<h4>Print and Setup instructions</h4>Printed using Overture3D PLA PRO filament. Layer height: 0.2-0.6mmInfill: 15% (or) more Variable layer height is optionalSupport: NoneCan be printed in PLA, PETG or ABS.

Planter Drainage Net Mesh - Different sizes

garden

Ferfi.

There are four versions. Variants 0,4 mm and 1 mm reffer to thickness of the flange. Slimmer 0.4 flange should “dam” the water less. Torture test variants are with grid-wall which allows greater water throughput and doesn't get clogged as easily. But it looks almost like stringing torture test prints.Intended to print with supports, as in the picture. Torture test has support structure modeled in as slicer would build supports through the wall-grid. Holes are approx. 2,5 mm large. Do not use PLA, anything else should be fine. Source files are provided in f3d.