helpro

ByteSlinger

This is an adapter ring (Spool tire) for use with Filamentive cardboard spools in Bambu Labs AMS. The ring clips into place on Filamentive cardboard spools and shields the outer edges from wearing down and producing cardboard particles when being used inside the AMS. This has specifically been designed to allow use with the AMS lid closed. If the spool is slightly larger than normal and pushes the edges of the tire out, causing rubbing on the inside of the AMS lid, remove the tire and try to compress the edges of the cardboard slightly then refit the tire again.

Filamentive Spool Tire (Adapter for use in AMS)

eds_3d_shop

⚠️Working on this complicated model takes a lot of time and if you like my work and want to support me and this design - please BOOST this design (click on the small Rocket 🚀 or „BOOST“ button) and print my bulletproof “Designer” printprofiles!🙏👍 Thank you in advance!🙏&nbsp;⚠️If you interested for pneumatic connector variant of this design - here is the <a target="_blank" href="https://makerworld.com/en/models/514558#profileId-430689" rel="nofollow noopener">AMSlite PTFE Tube Easy-Clip for PC-M10 pneumatic connector</a> 👌&nbsp;A1/A1mini AMSlite has a great design, but I think it would be nicer to have the option of connecting external filament dry boxes (or such <a target="_blank" href="https://makerworld.com/en/models/373405#profileId-273437" rel="nofollow noopener">Dust-Protector like my Duster</a>) with the help of PTFE tubes. And with the way filaments tend to wear out the edges of the feed funnel, it&#39;s nice to have some level of protection on the AMSlite. The PTFE connectors for AMSlite, which I could find so far either didn&#39;t hold properly or were very difficult to remove after installation 😳So, I designed my own😉, which has 2 clamps which hold the connector firmly on the funnel and release it easily when clamps will be loosing! 😎Additionally, I shaped PTFE channel in the way, that it points to the center of the spool and thus feeds filament into AMSlite at a more optimal angle. Even with almost empty filament spools, filament is fed into AMSlite at a better angle.These little helpers have beautiful dice symbols to number the filament inputs on the AMSlite. This is especially helpful when installing AMSlite vertically!&nbsp;Thanks to my supporter and tester <a target="_blank" href="https://makerworld.com/en/u/815356263" rel="nofollow noopener">SteveKratz</a> and <a target="_blank" href="https://makerworld.com/en/@Printwarrior" rel="nofollow noopener">PrintWarrior</a>! 🦾😍With their great help I was able to check and improve the functionality of this design!!! 🙏❤️👍<a target="_blank" href="https://makerworld.com/en/@SteveKratz" rel="nofollow noopener">Steve </a>- thank you for some awesome pictures too! 🙏&nbsp;⚠️This model must be printed in PETG filament! PETG is very important for the function of the clamps! Printed with PLA, for example, they won&#39;t last long on the AMSlite! ⚠️<h4>Print / Install Instructions:</h4>⚠️I recommend to use my print profiles - there are all these settings well done and tuned!<ul><li>place them with the number on the build plate</li><li>first layer line width: 0,38 (0.4 mm Nozzle)</li><li>first layer speed: 10ms per second (for perfect look of the button-surface)</li><li>first layer infill: 50ms per second (for perfect look of the button-surface)</li><li>3 perimeter, 5 top, 3 bottom layer, 15% infill</li><li>WALL generator: Classic (in this case please no Arachne) !!!</li><li>It is helpful to swith your Bambulab Printer from “Standard” Speed to “Quiet” - better quality and fit!</li></ul>⚠️Stick the PTFE tube through the inner hole about 1/8 of an inch (2mm), like you can see this in the pictures and it will keep the tube properly in!⚠️&nbsp;👌<a target="_blank" href="https://www.youtube.com/watch?v=pmIImYbayeM" rel="nofollow noopener">Just take a look at this video, here you can see how you can easily get these Easy-Clip Connector on the feeder properly!</a> 😍👍<figure class="media"><oembed url="https://www.youtube.com/watch?v=pmIImYbayeM"></oembed></figure>&nbsp;— ! —&nbsp;Thanks for downloading, rating in advance and please don&#39;t forget to like👍and to BOOST 🚀 this model! ;-)<h3>Take a look at my other very helpful designs for X1/P1P/P1S/A1/A1mini:</h3><figure class="image"><a href="https://makerworld.com/en/u/4051934936" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000467088/design/2024-04-29_48a4a378d552f.png"></a><figcaption>🔗<a target="_blank" href="https://makerworld.com/en/u/4051934936" rel="nofollow noopener">Eds_3D_Shop designs on MakerWorld</a> 🔗</figcaption></figure>&nbsp;If you like my work and want to support me - please follow me here and on Instagram. If you want - you can buy me a coffee! <a target="_blank" href="https://linktr.ee/eds_3d_shop" rel="nofollow noopener">https://linktr.ee/eds_3d_shop</a>Thank you for your support and.. happy printing!Ed ;-)&nbsp;

AMSlite PTFE Tube Easy-Clip-Connector

Modelicious Creations

Always short one pair of tweezers when using iron beads? This print can help! The model is designed with iron on beads in mind such as Hama, Perler or Pyssla, but it surely can be used for other applications equally well.&nbsp;I designed the tweezers to be strong and so that they would not twist when small objects such as iron beads are picked up. Yet at the same time I wanted them to be easy to print. Thus they only have a minimum of small overhanging areas where support is needed.&nbsp;The model uses as little as 4,6 grams of filament ant takes under 30 minutes.

Tweezers for Iron On Beads (strong, little support, easy to remove)

Noah

Merry_Husek

Download 4 kinds of rotating coasters that form different geometric shapes…They also serve as a test of your printer's tolerances (two versions available).

AMS

X1C

A1

Noah

Dies und Das