Helperrov

LayerCake

A basic Gridfinity Parametric Container done in Autodesk Fusion and now updated with an identical OpenSCAD project for even easier customization.&nbsp;Based on the excellent Gridfinity system by Zach Freedman Wiki: <a target="_blank" href="https://gridfinity.xyz/" rel="nofollow noopener">https://gridfinity.xyz/</a>&nbsp;Differeces from the standard design:<ul><li>The lip has an added 0.4 mm flat section on top.</li><li>The screw holes are tighter and have a step pattern for better printability.</li><li>The base units can be overwritten which breaks compatibility but can use all space available.</li></ul>Some preconfigured models were added in height increments of 3U ranging from 1x1x3 to 4x4x9.For other sizes just use the Customize button or configure your own through Autodesk Fusion. Please do not share print profiles here that break compatibility. Label print profiles well according to their settings. All profiles shared by me use the default settings aside from gridfinity units.<h2>OpenSCAD</h2><h3>Customization Options</h3>The basic customization starts at the width, depth, and hight of the container in gridfinity units. Additionaly the hole pattern for screws and magnets can be configured or completely removed.On to of that the base units for the grid can be redefined. This will break compatibility with the standard gridfinity baseplates etc. but will allow for much more flexibility when filling a drawer completely with containers.An equally modifiable base grid can be found in my other models <a target="_blank" href="https://makerworld.com/en/models/476846" rel="nofollow noopener">here</a>.<h2>Autodesk Fusion</h2><h3>Configuration</h3>Open the file in Fusion and adjust the size as needed.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000025376/design/2023-09-27_j5pt2zi2pyal.png"></figure>By default the magnet hole diameter is tighter than the standard 6.5 mm of the Gridfinity design as I found this to fit better. The depth has also been changed from the default 2.4 mm.<h3>Fusion Error</h3>If you design a 1x1 container the file will throw an error but the output should still be generated just fine. This is due to a pattern that no longer can be applied. If there is a way to suppress this let me know in the comments.<h2>Notes</h2>The Autodesk Fusion version was made with the personal version therefore non commercial only.The OpenSCAD version is licensed as MIT.Source files included.

Gridfinity Parametric Container

S úpravou

ngprint

Knurled Nuts offering great grip.Compatible with my Knurled Screws and standard Metal screws.Thread optimization ensures seamless fitting without the need for resizing.For optimal results, select a small layer height to ensure smooth thread formation.&nbsp;Compatible Knurled Screws:<a target="_blank" href="https://makerworld.com/en/models/398421" rel="nofollow noopener">M6</a><a target="_blank" href="https://makerworld.com/en/models/398427" rel="nofollow noopener">M8</a><a target="_blank" href="https://makerworld.com/en/models/398450" rel="nofollow noopener">M10</a><a target="_blank" href="https://makerworld.com/en/models/398454" rel="nofollow noopener">M12</a>Compatible fully printable Screws and Washers:<a target="_blank" href="https://makerworld.com/en/models/378318" rel="nofollow noopener">M6</a><a target="_blank" href="https://makerworld.com/en/models/378392" rel="nofollow noopener">M8</a><a target="_blank" href="https://makerworld.com/en/models/378447" rel="nofollow noopener">M10</a><a target="_blank" href="https://makerworld.com/en/models/378461" rel="nofollow noopener">M12</a>&nbsp;Recommended print settings:-0.16mm layer height-4 wall lines-4 top and bottom layers -25% Infill

Knurled Nuts

Ozubené kola

3Deste

This is my version of soldring wire holder.So simple as funcional.I use it with 250gr spool.Printed with PLA but every material is ok.Support not needed, layer high 0.2mm or higher, minimum 3 wall loops, infill 15%.If you like this model, please, leave a like and publish a picture of your print :)Alex&nbsp;

Soldering wire holder

Návrhy

ConTra

1/10 Jerry can

1/10

porlock

If you dont have AMS please check this layer swap Instructions:First layer 0.2mm all other 0,16mm Start with BLACK PLA BASIC At layer #8 (1.32mm) swap to PINK PLA BASIC or RED PLA BASICAt layer #13 (2.12 mm) swap to ORANGE PLA BASIC or YELLOW PLA BASIC At layer #16 (2.60 mm) swap to YELLOW PLA BASIC or WHITE PLA BASIC

Japanese complete nude anime girl.

obraz

pbbence1994

My next kit card is based on the famous P51-D Mustang warbird. Looks Best with silk silver filament. Cut the parts out with pliers, nail sissors or hobby knife. The assembly is easy and self explanatory. The parts should fit together tightly, but you can always use a bit of super glue to secure the parts together. If you don't need the frame I uploaded the model without it. Please keep in mind that the fine texts and details require very fine lines on the first layer so you need perfect bed adhesion. I recommend to use some adhesion spray like 3dLac. Stay tuned for more kit card planes! Have fun printing it!

Plane Kit Card (P-51D MUSTANG)

Letadla

Lele88

A keychain with the Fendt logo

Fendt Keychain

Karavan

madizmo

This is the latest version of my AMS saver after bambu asked me to take down my old models. Apparently some people managed to damage the feeder leds with some of the previous models. This version mounts to the top of the feeder unit using double sided sticky tape so there is absolutely no chance of causing any damage to your AMS unit. I used the clear 1mm thick sticky tape off Temu on mine and they are stuck very well. I&#39;ve been using 100mm ptfe tube with no issues, if you seem to get loading issues try 85mm. The ID of the ptfe hole is 4.2mm but because of the print orientation it can still be tight, i run an allen key through it along the top edge to smooth the layers a bit. You can play with flow rate a bit as well if too tight&nbsp;works best with my <a target="_blank" href="https://makerworld.com/en/models/172221#profileId-189118" rel="nofollow noopener">filament guides</a>, the ones in the pictures i&#39;m still testing but the originals work great&nbsp;&nbsp;Disclaimer: This is a modification to the machine and any issues caused by these mods will not be covered by Bambu.

AMS Saver V5

AU3D

While splitting hooks from the main part has its benefits, I find this method problematic when it creates more issues than it resolves. That's why I opted to attach permanent hooks to the hanger, eliminating the need for additional installation steps. This approach proved to be more efficient and reliable for me.<h3>Skadis Collection</h3>I am constantly developing more IKEA Skadis attachments. Check out my <a target="_blank" href="https://makerworld.com/en/u/2942852598/collections/188108" rel="nofollow noopener">IKEA Skadis Collection here</a>.