hauerdea

Rafał

Fishing leader organizer for method feeder. Space for 16 pieces. By using springs from old pens, the leader attachment is adjusted to its length. The springs used have a wire thickness of 0.4 mm, a diameter of 4.3 mm and a total length of approximately 32 mm (if you have shorter ones, you can stretch them). If the hinge pin doesn&#39;t want to go in, put it in the freezer for a few minutes and it will go in without a problem :)

Organizer for method feeder leaders

Fishing

Hanak1nSolo

Ikea Ivar shelf hook. Because the ones you can buy are more expensive.Printed in BambuLab PLA Matte white.Used 3 perimeters and 100% infill.

Ikea Ivar Hook

Home accessories

BEAMink

I have remodeled the 3D Printing deburring tool and fixed some issues.The original was a model I made years ago for myself and friends. I never thought It would get so many downloads and there was a need for this, so I figured I owed it to everyone to remodel it and address some issues with Version 1&nbsp;V2 now has mush easier threads, tighter bit tolerences, (Less wobble), greater bit extension and all around nicer model. &nbsp;Put a little grease where the bit goes before assembly and it helps with seating the bit.&nbsp;Bits @ <a target="_blank" href="https://a.co/d/eMfLUbm" rel="nofollow noopener">https://a.co/d/eMfLUbm</a>&nbsp;Thanks for the support!

3D Printing Deburring Tool V2

Tools

cagriahiskali

IMPORTANT: You have to tune your slice settings exactly as shown on the pictures.This time Box type of silica gel container. Much easier to print and less filament. Snap-fit lid. No screws. Only 30 min to print one box. Much aesthetic and no strings.&nbsp;

Bambu Lab AMS Desiccant Box / Silica Gel Container [EASY PRINT 30min]

AMS upgrade

Julia Ebert

This is a big toy human figure that's inspired by a Lego minifigure. I spent a lot of time making this model from scratch to match the original design while making tweaks for tolerances, printability, and strength. While there were a number of minifigure models I found online, most were not designed for printing, which is a particular challenge for the leg, arm, and hand joints. I'm particularly proud of the universal clip I designed for these, which makes for easy assembly and stiff-enough joints to pose your figure.I designed the clips and tolerances for this model to be printed at 100% (10x original Lego scale), but people have previously had success printing my <a href="https://www.printables.com/model/78695-mega-lego-like-skeleton-101-scale" rel="nofollow">10x Lego-like skeleton</a> at smaller scales (eg, 50% or 5x Lego-scale).Now that I have a base model for a Lego-like figure, this opens up a host of options for specific Lego-like figures. If there's something particular you're interested in, leave a comment or send me a message! If you want to make your own modifications, I've included STEP files for all parts (just be sure to give credit for my original design).Fully assembled, this model stands 40 cm (~16 inches) tall. I printed mine with Hatchbox true blue PLA, Hatchbox true red PLA, and Prusament mango yellow PETG.<h4>Printing Instructions</h4>I've included 3MF files for all parts, and parts should import correctly oriented for printing.<ul><li>For PrusaSlicer 2.6+: you just need to load the project file. (This makes use of organic supports, for the legs, which are added with PrusaSlicer 2.6.)</li><li>For other slicers: I've included details about special instructions for all parts, so you should be able to replicate anything necessary for proper printing. Except where otherwise noted, I printed parts in PLA at 0.15mm layer height with 7% cubic infill and without supports.</li></ul>You will need to print:<ul><li><code>32x-connector-pins.3mf</code>: You should need 30 pins for assembly (or 26 if you print the solid head); this has 2 extra just in case. If you have trouble with bed adhesion, add a brim</li></ul><h5>Legs</h5><ul><li><code>legs.3mf</code>: Uses tree supports the top of the lower hole on the leg.</li><li><code>hips.3mf</code></li><li><code>2x-limb-clips.3mf</code>: This file contains two clips. You'll need to print one set of two in the arm/body color, and one set in the leg color. Important: I recommend printing this in PETG or ABS with 25% infill, because it will have to flex and PLA might snap.</li></ul><h5>Body</h5><ul><li><code>arms.3mf</code>: These print with a small surface area on the bed (the wrists), so you might want to add a brim if you have trouble with bed adhesion.</li><li><code>body.3mf</code></li><li><code>2x-limb-clips.3mf</code>: This file contains two clips. You'll need to print one set of two in the arm/body color, and one set in the leg color. Important: I recommend printing this in PETG or ABS with 25% infill, because it will have to flex and PLA might snap.</li></ul><h5>Head & hands</h5><ul><li><code>2x-hands-wrists.3mf</code>: Requires supports on the underside of the wrist clip. Like the limb clips, I recommend printing with PETG (or similar) with 25% infill.</li><li>One of: (all require supports on the underside curve of the head)<ul><li><code>head-face-mmu.3mf</code>: Print the head & face as one part with some sort of multi-material printer (e.g., Prusa MMU or Bambu AMS). Use supports on the underside curve of the head.</li><li><code>split-head.3mf</code> and <code>face.3mf</code>: Print the head (with cutouts) in two pieces. Use pins and glue to connect the halves. Print the face separately and glue it in.</li><li><code>solid-head.3mf</code> and <code>face.3mf</code>: Print the head and face as separate prints. Use supports on the underside curve of the head. Then glue the face parts into the head.</li></ul></li></ul><h4>Assembly Instructions</h4>In addition to the printed parts, you will need cyanoacrylate glue (CA glue/superglue). <h5>Legs</h5><ol><li>Glue the pins into the top of the hip. Add glue to the holes and bottom surface of each of the hip pegs and attach. Important: The slope of each hip peg should be facing out to the sides. If the pins don't want to go together, check that you have this orientation right!</li><li>Use the same gluing approach to attach the limb clips to each side of the hips.</li><li>Gently but firmly press each leg onto the clips. It should snap into place. The hips are symmetric, so you can't put the legs on backwards. This requires a fair bit of force, but you shouldn't need a hammer. If it won't go on, slightly sand or file down the outer head of the limb clip (rather than the inside of the hole on the leg). Warning: The clips are not designed to come out once they're attached, so make sure you're ready.</li></ol><h5>Body</h5><ol><li>Glue the limb clips into each arm, like you did for the legs.</li><li>Glue the wrist onto the hand, with the pins. Because of the relative print orientations here, it's best to use a bit more glue here to make sure it stays on.</li><li>Press each wrist clip into the arm. (They're the same, so you can't put in the wrong hand.)</li><li>Press each arm clip into the body. The body is also symmetric, so you can't put the arms on backwards.</li></ol><h5>Head</h5>If you printed the separate head and face pieces, glue the face pieces into the head. You may need to file or sand some of the face pieces to fit, depending on how well the supports worked.<h4>License Note</h4>This model is marked as non-commercial because I don't want anyone (including myself) having Lego come after them with a lawyer. If you choose to sell prints of this model, you do so at your own risk!

Mega Lego-like Minifigure (10:1 scale)

Oblíbené

maxaruta

With this test, you can perfectly understand the tolerance of the thicknesses of your printer, and be sure of the spaces to leave between the walls in order to obtain a sliding insert that fits perfectly. In addition, you can accurately discover what measurements to use to print "Print-in-place" pieces.&nbsp;Italian:Con questo test, puoi capire perfettamente la tolleranza degli spessori della tua stampante e avere la certezza di quali spazi lasciare tra le pareti per ottenere un inserto scorrevole che si adatta perfettamente. Inoltre, puoi scoprire con precisione quali misure utilizzare per stampare i pezzi "Print-in-place".

Fishing

Home accessories

Tools

AMS upgrade

Oblíbené

Test print