p1s, smooth plate, generic PLA. default profile. no issues with the print.

p1s, smooth plate, default profile, Bambu green PLA. no issues. needed a small part tray for extruded disassembly and this is great for that.

p2s, smooth plate. trying to dial in a silk silver PLA from Geeetech. once I remembered to add the gcode. it worked fine. only printed the 240-225 portion

p2S, smooth plate, default profile, generic white PLA. printed at 150%. used plate #3. no issues with the print. cut the base a bit so it would sit flat. painted it with liquid chrome.

p1s, smooth plate, generic copper PLA, default profile. no issues with print but had to use m3x8 self tapping screws since I couldn’t find the official Bambu screws that were supposed to come with the blade. note: shown on P2S in pic,

p2s with AMS 2 Pro, silver PETG, smooth plate, long leveling legs. default profile, printed in Sport mode. no issues with the print. (I printed the longer leveling legs with my P1S) The silver PETG from Giantarm was a good color match for the P2S chassis. i did notice that the longer legs fit perfectly on the front of the AMS 2, but the shorter ones had to fit one slot back. Didn’t add the lighting b/c the p2s is bright enough as is, but I may add some colored lights controlled by HA to indicate status (idle, busy, complete, error). anyhow, nice print. Thanks.

p1s, default profile, smooth plate. generic grey PLA and Bambu black PLA. I took off a star because the supports are _extremely_ hard to remove on the lettering and the Bambu logo. also, the tolerances are very tight on the magnet holes. still, it’s a nice looking print after an hour or so of fiddling.

p1s, smooth plate, default profile. easy print, works well

P1S, smooth plate, grey PLA, default profile. so, I printed this and realized that I didn’t have any 4mn magnets, but only had 3s and 5s. it was a good thing I wasted a print because I didn’t add the negative feature to the bottom hinge (got the idea from a previous comment) and the hinge didn’t work. after a slight resize (108%) and the negative ibject addition it printed fine for my 5mm magnets.

easy print. P2S, black PLA. textured PEI plate, default profile. no issues. thanks!

P1S smooth plate, default profile for everything except the transparent bits. p2s, textured PEI. plate for the tube and flame (transparent PLA). I was pleasantly surprised by how clear the transparent PLA turned out. printed three with different base colors. no issues with the print. I did combine the tube and flame on the same plate and used print by object.

printed plate 5 for the LR44s. blue PKA, default profile, textured PEI plate, P2S. easy print. thanks!

p2s, grey PETG, textured PEI plate, default profile. easy print. fits well. dedicated funnel would be nice, I’m still stepping on dissonant beads, but that’s a me problem. the print is great!

printed in white PLA. increased size slightly to fill build plate on diagonal. P1s, smooth plate, default profile. print turned out great. daughter got engaged here so it will make a great present. painted with acrylics.

p1s, smooth plate, default print profile. printed in grey and yellow PLA. printed three times. once with default settings, once with increased Z height to be able to store a full (120) wire set of 20 cm DuPont wires, once cut in two (moved letters over) and increased Z height to store full set (120) of 10 cm DuPont wires. prints came out ok.

p2s, textured PEI plate, default profile, black PETG. easy print. they work eell. thanks!

p1s, smooth plate, default profile. used red, white, yellow, and black PLA. didn’t bother make the goggles grey - used white. easy print. no issues removing supports. fit together easily. used short pieces of wire for alignment and superglued it up.

p2s, textured PEI plate, black PLA, default profile. I wonder if the supports required to print the sides with cutouts take more filament than solid sides would have taken. no matter. it’s a fine print.

p2s, textured PEI plate, default profile. added 18650 lettering to top, printed in black and white PLA. I liked the fact that the holes for the 18650’s are oversized enough to handle some slightly larger rechargeable 18659’s that I had on hand, nice print. worth a boost.

p2s, textured PEI plate, default profile, black PETG. no issues with the print.