flippo24

Meister Edel

HeyhoHere I have a completely 3D printable pulley for you!I recently designed an attachment for my clothesline (which also works great!) and of course the idea came up to simply use a pulley! Previous designs I found online always needed extra parts or didn't look very sturdy.So I designed my own solution and tested it for you!There are 3 different versions:<ol><li>Easy to print pulley </li></ol><figure class="image image_resized image-style-align-center" style="width:60.29%;"><img src="https://makerworld.bblmw.com/makerworld/draft/257469/2023-12-11_li760f9y0kfc.jpg"></figure>A quick printed version where there is only 1 main part. Due to the slightly thinner suspension, this version fits well into most hooks or can also be attached with a rope. The disadvantage is that it is less stable than the other versions due to the print orientation. Nevertheless, it is more than sufficient for most tasks!<ol><li>Strong pulley </li></ol><figure class="image image_resized image-style-align-center" style="width:43.4%;"><img src="https://makerworld.bblmw.com/makerworld/draft/257469/2023-12-11_dmgi5c9h190e.png"></figure>This version is particularly solid and can be printed even more stably thanks to the optimized alignment. After printing, simply put the 2 halves together with the small pin in the middle and after inserting the roller, the version is sufficiently stable.If you prefer, you can also put the two halves together with a little glue.<ol><li>Pulley for eyelets </li></ol><figure class="image image_resized image-style-align-center" style="width:44.39%;"><img src="https://makerworld.bblmw.com/makerworld/draft/257469/2023-12-11_brsqi4i0b1h2.jpg"></figure>This version can also be used in combination with eyelets, where the two previous versions cannot simply be used. However, you must first assemble the individual parts on the eyelet. The halves should not be glued together! Unless you don't want to remove it from the eyelet!ScalabilitySince all 3 variants are completely 3D printed, you can also scale them "at will"! So make them bigger or smaller! But always keep an eye on the tolerances and the perimeters!<figure class="image image-style-align-center image_resized" style="width:64.6%;"><img src="https://makerworld.bblmw.com/makerworld/draft/257469/2023-12-11_fkehzyjntfko.png"></figure>Printing tips:You should use as many perimeters as possible (6 Perimeter should be enough with the given size). Infill at 100% brings the remaining stability. PLA is probably sufficient for short loads. For continuous loads, I would recommend PETG or other stable materials. <figure class="image image_resized image-style-align-center" style="width:64.76%;"><img src="https://makerworld.bblmw.com/makerworld/draft/257469/2023-12-11_0wdhexfkw5rp.png"></figure>Post processing:As the friction between the 2 parts of the roll naturally increases with higher loads, some oil must be added. I simply used some chain oil from my bike for this. To make it easier to add the oil, I constructed 2 small openings on each side of the wheel. Simply pour in some oil here, move the wheel back and forth a little and then remove any excess oil.<figure class="image image_resized image-style-align-center" style="width:67.55%;"><img src="https://makerworld.bblmw.com/makerworld/draft/257469/2023-12-11_tpfg6durgksg.jpg"></figure> Slicing Tipps: If you are struggling with some parts you can separate them into single objects and scale them up/ down a little to get a perfect fit!<figure class="image image_resized image-style-align-center" style="width:66.09%;"><img src="https://makerworld.bblmw.com/makerworld/draft/257469/2023-12-11_plja8r5232v4.png"></figure> Have fun!

Strong Pulley 100% 3D Printable, Scaleable & Durable

Büro

squinn

Rest your book or tablet on this convenient stand, allowing you to keep your hands free while cooking, working, or studying. This is a completely print-in-place design, with the exception of the two small articulating arms which are designed with a bit of flex in them so that they can be snapped in post-print.&nbsp;The model is designed to fold flat, so that it can be easily transported in a bag or slid into a space on a shelf. When opened up it then offers a few different adjustable angles that it can hold a book or tablet at, or you can extend the support arm past the notches for a low angle viewing mode. The arms then have some intentional slotting built into the pivot joints so that they can be optionally used to loosely lock into place at various positions to help hold the pages of a book.&nbsp;In addition to the standard model (which is shown in most of the pictures), there are also versions that include three different sized plaques just above the center area. These allow you to conveniently customize your stand with text in the slicer, such as in the following picture:&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3485677045/draft/2023-09-26_9e6f95ee3afd2.jpeg"></figure>

Foldable Book or Tablet Stand

Haushalt

RoB.G

<ul><li>Tube 4mm</li><li>Cable 5mm </li><li>Petg</li><li>Layer Height 0,16</li></ul>

BambuLab Clip for tube and cable  

P1S Zubehör 

lindnjoe

Warning!! This takes patience to put together. Round Deer and Snowman Lantern with 3 thin layers that fit into a base. The layers have tabs on the bottom that fit into the slits on the base. The front layer with the snowman and deer is printed in two parts, you will need to put those two layers together to make one. The layers are printed very thin at 0.2mm. Be careful when taking them off the heat bed. Slide the tabs on the end into the slits on the opposite end.You can size up or down. For best results size up.I recommend a dab of glue on a couple tabs per section to hold the round layers to the base.3 Layers to print and 1 base. &nbsp;A tea light will sit in the middle. You need patience when putting this together.

Büro

Haushalt

P1S Zubehör

Weihnachten