falcof

Thicc

Are you tired of boxes slipping and sliding around your trunk? Not anymore with these vehicle trunk retainers. Construction is easy. Print and attach 20mm velcro hooks to the retainer&#39;s foot. The best aspect of this design is the velcro allows for the retainers to be infinitely reused and reorganized.&nbsp;Print Settings<ul><li>Use a 0.4mm nozzle, I cannot guarantee the success of other sizes</li><li>warmer climates should consider printing this in ABS or ASA</li><li>15% infill</li><li>.25mm first layer to improve adhesion.</li></ul>Update - proven that articulated retainer can print laying flat, which is much easier and quicker to print. Print profile adjusted to include this change

Car Trunk Velcro Retainer 

tools

BamBam Design

<h4>Toroidal Windmill - Self adjusting turbine</h4>Looks like a spinning flower and no much wind is needed.<a target="_blank" href="https://youtube.com/shorts/WrKHW2Cdyvk?si=byQ_EpJAfOOy8x7F" rel="nofollow noopener">YouTube Short</a>&nbsp;<ul><li>Beautiful Windmill with toroidal Propeller Blades</li><li>Self adjusting to wind direction (Tail Blade Reworked)</li><li>100% printed, no Screws or tools needed</li><li>You can add 3 Propellers on one Axle with 2 distances</li><li>Full customizable with different propeller sizes and directions (I plan to add more cool propeller types as well)</li><li>Rods are stack able to your needed height</li></ul><h4>Printing:</h4>You can choose Propellers from 3 Print Profiles<ul><li>Basic Parts with Left&amp; Right Propeller to choose</li><li>Additional Propeller Blades</li><li>Additional Slower Propeller *New</li></ul>You can mix the propellers from these profiles.<ul><li>added one profile for A1mini without the biggest blade as well</li></ul>The rod could be a bit difficult to print, i added custom support, but clean your buildplate and apply some glue.&nbsp;PETG &amp; PLA tested👍🏼<h4>Assembly:</h4><h4>Info:</h4><ul><li>Added custom support to the horizontal printing rod</li><li>Added optional longer axle for more distance between propellers (10mm instead of 5mm).  With stronger wind the bigger blades should not collide.</li></ul>The Pitch from the Basic Blades:<ul><li>Big - Pitch 195mm</li><li>Med - Pitch 170mm</li><li>Small - Pitch 135mm</li></ul>Additional Propeller Blades with different numbers of Wings:<ul><li>Big - Pitch 190mm</li><li>Med - Pitch 160mm</li><li>Small - Pitch 130mm</li></ul>Additional “Slower” Propeller Blades:<ul><li>Big - Pitch 400mm</li><li>Med - Pitch 325mm</li><li>Small - Pitch 250mm</li></ul>Thanks to all followers and don&#39;t forget the virtual handshake 👍 ….Happy Printing&nbsp;Info II:My other windmills are fully compatible if you want to mix it up:<ul><li><a target="_blank" href="https://makerworld.com/models/235261" rel="nofollow noopener">Toroidal Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/250216" rel="nofollow noopener">Honeycomb Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/388124" rel="nofollow noopener">Elliptical Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/425419" rel="nofollow noopener">Sunflower Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/454861" rel="nofollow noopener">Raccoon Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/255324" rel="nofollow noopener">CLAMP for Windmills</a></li></ul>Info III:More modifications you find on my Patreon account.<figure class="image"><a href="https://www.patreon.com/posts/mod-608-bearing-105175595" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000235261/design/2024-05-30_3ad9786c3df1b.png"></a></figure>&nbsp;<figure class="image"><a href="https://www.patreon.com/posts/mod-pole-adapter-103628897" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000235261/design/2024-05-30_70c92ad1f54a9.png"></a></figure>&nbsp;Commercial license you can get here:<a target="_blank" href="https://www.patreon.com/BamBamDesign/membership" rel="nofollow noopener">https://www.patreon.com/BamBamDesign/membership</a>

Toroidal Windmill - Customizable system

project

TuringComplete

Card holder display

Boardgame components 

Hiro Koiso Racing

This model is designed to fit X1 and P1 series printers. HKR poop chute features interlocking leg to secure the chute to the printer body without extra hardware or magnets. ※Fitment Note: If you got X1, X1C and P1P in Feb 2023 and earlier (most likely built in 2022) , Your printer might have shorter legs than current version. This can cause a printer to not sit level with the chute installed. How to tell if you have a early style short leg printer<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-05_177ad051bd84f.jpg"><figcaption>Print The chute and see if the round part of base can slid under the printer as pictured. If it goes like picture above, you have current style. no further action is required. If the chute base doesn't goes in, follow instructions. Scroll down for further information</figcaption></figure> <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-02_0f1d75fb4cc6e.gif"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-02_8219b55930c54.gif"><figcaption>Easy printing - It prints without support.</figcaption></figure>Removable bucket are easily access from front and available in 4 sizes.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-02_52e2e363fc345.gif"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-02_ec5da20ffb566.gif"></figure> <img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-02_7002ac682aaca.jpg"> 《Solutions for early short leg printers clearance issue 》 2 ways for fix - both methods raise the printer height to same as current version to correct clearance issue. So print whichever you prefer and install to an early style printer. (Files are available for download)<ol><li>Replacement TPU leg - Extended legs replace stock rubber feet. Print with TPU <img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-05_ab7611200d584.jpg"> <img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-05_5d39951f13735.gif"> </li><li>PLA spacers - PLA or whatever rigid filament material you used to print the chute would work. They fit inside the leg pockets, use with stock Rubber feet <img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-05_ac0d4c15d6753.jpg"> <img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-05_e325c22380ea.gif"> </li></ol>Tip for leg replacement:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-05_828fd7817fbe4.jpg"><figcaption>Bring a leg to the edge one by one to replace. So you don't have to lay printer on side.</figcaption></figure>&nbsp;&nbsp;Checkout more HKR printer accessories: <a target="_blank" href="https://makerworld.com/en/u/2567436854" rel="nofollow noopener">https://makerworld.com/en/u/2567436854</a>&nbsp;・HKR Stackable Build Plate Storage: <a target="_blank" href="https://makerworld.com/en/models/120963#profileId-130105" rel="nofollow noopener">https://makerworld.com/en/models/120963#profileId-130105</a><a target="_blank" href="https://makerworld.com/en/models/120963#profileId-130105" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-02_1f77d220d2196.jpg"></a>&nbsp;・Foldable AMS side mount spool holder - No Bearing: <a target="_blank" href="https://makerworld.com/en/models/145321#profileId-158083" rel="nofollow noopener">https://makerworld.com/en/models/145321#profileId-158083</a> <a target="_blank" href="https://makerworld.com/en/models/145321#profileId-158083" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-02_119fd552797b3.jpg"></a>&nbsp;・Foldable AMS side mount spool holder - with Bearings: <a target="_blank" href="https://makerworld.com/en/models/153090#profileId-167255" rel="nofollow noopener">https://makerworld.com/en/models/153090#profileId-167255</a><a target="_blank" href="https://makerworld.com/en/models/153090#profileId-167255" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/666492/2024-03-02_25f94a5385d15.jpg"></a>&nbsp;Happy printing!

HKR Interlocking Poop chute with removable bucket

P1S upgrade 

Pepper Plant Marker