evanmartinezcontact

MakerVerse Designs

Fully 3d printed crocs shoes<ul><li>Printed with Overture TPU</li><li>PLA for the snap button</li></ul>Important notes:<ul><li>It is for EU shoe size number 42 (male), but you can scale every part (CrocsL1,CrocsR1,Holder,Mount1,Mount2) to your size (use uniform scaling)</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425034/design/2024-04-19_0266f756a989a.png"></figure><ul><li>If the shoe is too big to fit to the printers height, use the “WithSupport”-Version, rotate in Y-Axis (green) and use the cut tool in Bambu Studio to create a new flat surface parallel to the print bed<ul><li>I uploaded an .stl file without cut on the bottom for better scaling</li></ul></li></ul>&nbsp;<ul><li>There are two ways to print this:</li></ul><ol><li>Use a textured PEI bed and print it standing up without support</li><li>Or use another not so sticky bed and print it standing up with support</li></ol><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425034/design/2024-04-12_cc0523cbae068.png">&nbsp;If you can&#39;t get enough of printed shoes, check out my new model (Slide Shoes, Adilette):<a target="_blank" href="https://makerworld.com/en/models/488792#profileId-401842" rel="nofollow noopener">https://makerworld.com/en/models/488792#profileId-401842</a><img class="image_resized" style="width: 41.76%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425034/design/2024-06-08_bb258037ea2a1.png">Have fun with it and leave a like or subscribe if you like it!If there are any suggestions for improvement, feel free to write a comment.

Crocs Shoes - Fully 3d-printed

Shoe

Xander Designs

Miniature spark plug keyringPrinted with 0.2mm nozzle at 0.06mm layer heightTotal size when assembled is less than 5cmMulti part print just glue the pieces together with a little CA superglueSell my prints commercially by joining my <a target="_blank" href="https://patreon.com/xanderdesigns?utm_medium=unknown&amp;utm_source=join_link&amp;utm_campaign=creatorshare_creator&amp;utm_content=copyLink" rel="nofollow noopener">Patreon</a>&nbsp;

Spark Plug Miniature Keyring

.2mm Nozzle

chameko小廢物電波塔

<blockquote>12/06 After many tests, I successfully found out the cause of the assembly problems reported by some users, and modified the side panel file "AMS Dry Box-SW_v2".NOTE!I Designed this model not only for ams, I also used it in the vacuum bag that holds the filament, so I needed tight tolerances to make the box strong enough. The tolerance is 0.3mm, please be sure to confirm before printing this model.</blockquote>Open the side lid and pour about 60g of silica.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_92a6870d48198.jpeg">&nbsp;There is a buckle design on the top, please make sure it is buckled correctly when installing.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_2f71bc9cf33e9.png">&nbsp;&nbsp;The front and back of the V2 version have relaxed tolerances in most areas, making it easier to install. I kept the last small area because without this part, you might get the box and slide it open like in the second picture, resulting in a mess.Please be careful not to install it in the wrong direction when installing.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_fcf2db2bab532.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_210d78c4699ec.jpeg">&nbsp;If you have trouble assembling them, try using a heavy object to knock them into the correct position.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_e0f13f6121362.jpeg">&nbsp;As for why I used this complex design, it was because I considered that he had to withstand several kilograms of impact from the filament, so I wanted to distribute the force as equally as possible to each part.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_90a605e9c843e.png"> <blockquote>Also I have a beautiful model related to AMS! Don’t miss it!</blockquote><figure class="image image_resized image-style-side" style="width:56.75%;"><a href="https://makerworld.com/zh/models/99476#profileId-106044" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-23_3d850a0169288.jpg"></a></figure>Do you always find the AMS feeder difficult to press? Are the models on the Internet very difficult to install? I have improved and carefully designed this model. Please be sure to try it!(click on the image to go to the page!)&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<blockquote>----------中文解說----------</blockquote>打開側蓋後約可倒入60g的乾燥劑. 上方具有卡扣設計,安裝時請確認有正確的扣上.&nbsp;V2版本的正面與背面放開了大部分區域的公差,使其較容易安裝. 我保留了最後一小區域,因為沒有這個部分的話,你可能再拿取盒子時像第二張圖一樣滑開,導致一團糟. 安裝時請注意不要裝錯方向.&nbsp;如果你在組裝上遇到了困難,可以嘗試使用重物敲擊他們使其安裝至正確的位置. 至於為什麼使用這種複雜的設計,是因為我考慮到他必須承受數公斤來自線材的撞擊,因此我想盡可能地讓力量平均分攤到每個部分.

AMS Silica Gel Box[V2]

Willi 3D

Create your BaBo organizer! A system created to store them all!&nbsp;Description:This is the BaBo drawer module 30. The drawer module is the heart of the system as it carries the inserts and is therefore the main page of the system.&nbsp;The usable dimensions of the drawer are 240x210x30. The drawer has space for 8x7 inserts. The inserts have a grid of 30x30mm, this means a 1x2 insert has the dimensions 30x60mm.&nbsp;BaBo organizer is a stationary, very flexible system to store your tools, spare parts and even printing plates. The design is based on the iconic look of the Bambu Lab X1 printer.&nbsp;It was important to me that even newbies could print and use the system, which is why all parts are printed without support and the parts are already pre-sliced.&nbsp;Furthermore, all inserts for the accessories and tools that the printer comes with are free. Only the special modules and inserts are only accessible to members of my club. The purpose of the club is to promote my work and to reduce the costs that I incur. I would also like to find people who are interested in expanding this system.&nbsp;The entire system uses only 1 type of screw, M3x8 countersunk screws.Links:<ul><li><a target="_blank" href="https://makerworld.com/de/u/24485025/collections/12914" rel="nofollow noopener">BaBo collection</a></li><li><a target="_blank" href="https://makerworld.com/en/u/24485025/collections/666853" rel="nofollow noopener">BaBo duo collection</a></li><li><a target="_blank" href="https://makerworld.com/en/u/24485025/collections/666866" rel="nofollow noopener">BaBo inserts</a></li><li><a target="_blank" href="https://www.printables.com/@Willi/store" rel="nofollow noopener">Exclusive models, printables. (Credit card)</a></li><li><a target="_blank" href="https://than.gs/u/1578655?plans=true" rel="nofollow noopener">Exclusive models, thangs. (Paypal, Credit card)</a></li></ul>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000014125/design/2023-09-20_95fdae0c8d181.jpg"></figure>Update:(13/09/23)<ul><li>Assembly optimizations</li></ul>(31/10/23)<ul><li>improved connection between modules</li><li>easier to push back the drawer</li><li>print profile optimizations</li></ul>(26/01/24)<ul><li>design optimizations to prevent warping</li></ul>&nbsp;Printing:Layer height: 0.2Supports: NoBrim: NoMaterial: all&nbsp;Assembly:Follow the instructions in the picture.<ul><li>printed parts</li><li>16 x M3x8 countersunk screws.</li></ul>If you like this model, please throw me a like. Designing the models is time, filament and coffee consuming. <a target="_blank" href="https://www.paypal.com/donate/?hosted_button_id=WGL5LXN5EHEXN" rel="nofollow noopener">If you want to support my work buy me a coffee (PayPal).</a> Thanks!&nbsp;Clubcontent:<figure class="image"><a href="https://www.printables.com/@Willi/store" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000014125/design/2024-06-13_ccadb89c071b7.jpg"></a></figure><figure class="image"><a href="https://www.printables.com/@Willi/store" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000014125/design/2024-06-13_c05e6d1cbb9c7.jpg"></a></figure>

Shoe

.2mm Nozzle

X1

A1 Mini