二队长么

芸芸众生

这款铁氟龙支架在保证灵活性的同时，还能具备一定的气密性。最好是按照我的摆放方式打印，这样比较保险，并且我的打印文件中是添加了手动支撑树的。可以直接买上图的气动接头，也可以使用我提供的临时解决方案，就是那个像气动接头的玩意。如果你有气动接头可以把那两个代替品删掉。有单孔和4孔可选大家喜欢就行。

A1铁氟龙管支架 对接头

其他

OJum

My new gun design, Ak-47 in its basic version with connector for assembly without glue.Connector hard: They hold well but are difficult to fit in.Connector light: They hold little but are easy to fit in. Practical if you want to align the parts to stick them.Size: 87cm

AK-47

Soap_Warrior

香蕉爪刀 摘要：这是一把以香蕉为原型，结合伸缩爪刀而设计的香蕉爪刀，不需支撑方便打印，除了3D打印的零件之外，还需要两个直径10mm厚度2mm的磁铁。 Abstract: This is a banana claw knife based on the prototype, combined with the design of the telescopic claw knife, which is convenient for printing without support, in addition to the 3D printed parts, it also needs two magnets with a diameter of 10mm and a thickness of 2mm.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_5663645a5bc53.gif"></figure> 主要零件：香蕉1*1、香蕉2*2，香蕉刀刃*1、连接块*1、直径10mm厚度2mm磁铁*2，如下图所示： Main parts: banana 1*1, banana 2*2, banana blade*1, connecting block*1, diameter 10mm thickness 2mm magnet*2 as shown in the figure below:<img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_c2547b7f91a85.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_8c182f640bb7e.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_23c7e3e309af8.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_e9d884e12d496.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_31d257e313e9c.jpg"> 组装过程：1.将磁铁装入香蕉1零件的2个凹坑内，并使用胶水固定。注意：保证两磁铁相吸！ Assembly process: 1. Load the magnet into the 1 pit of the banana 2 parts and fix it with glue. Note: Make sure the two magnets attract!<figure class="image image_resized" style="width:50.42%;"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_64b61a5eb48e2.jpg"></figure> 2.将香蕉刀刃装入香蕉1零件，确保刀刃能够正常滑动。 2. Load the banana blade into the banana 1 part and make sure the blade slides properly. <img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_b69a26ab655a8.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_77246da017ec7.jpg"> 3.将连接块卡入香蕉2零件中并用胶水固定。（最新的连接块为了方便安装两端增加倒角）。 3. Snap the connecting block into the banana 2 parts and fix it with glue. (The latest connecting block adds chamfers at both ends for easy installation).<figure class="image image_resized" style="width:44.78%;"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_97bc91e5d88a5.jpg"></figure> 4.将香蕉2与香蕉1零件进行组装，并使用胶水固定。注意：不要使用过量胶水，可能会导致刀刃粘连！ 4. Assemble Banana 2 with Banana 1 parts and fix them with glue. Note: Do not use excessive glue, it may cause the blade to stick！<img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_fb18fe34b9138.jpg">&nbsp;

其他

枪

玩具