eddietheman2006

3DXAV

High precision design of 3D model Phone Case for 3D printing in TPU elastomerThe case fits perfect and it has Pen Holder!

SAMSUNG GALAXY S21 ULTRA CASE WITH PENHOLDER

phone

SNASA

This is a small and stealthy minimalist heat insert press designed for CNC Kitchen TS100 heat insert set. I didn&#39;t want to use a counterweight so I made an invisible spring and belt system hidden in the vertical part. Its size makes it perfect for small job on the workbench :<figure class="image image_resized" style="width: 42.73%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000430484/design/2024-04-18_a86cd65962c1d.jpg"></figure><figure class="image image_resized" style="width: 42.59%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000430484/design/2024-04-18_4f0eadde94f.gif"></figure>&nbsp;The sides are super convinient to store everything you need (there is also a spot for a small alen key).&nbsp;I have added the step files if you want to design your own soldering iron mount or use a different base.&nbsp;Miscellaneous:<ul><li>20 * M3 brass insert</li><li>22* M3x8</li><li>1 * M3x6 screw</li><li>2 * M3 Nut</li><li>3 * M3x25 screw</li><li>7 * M5 nut</li><li>6 * M5x10 or M5x12 screw</li><li>1 * M5x16 thumb screw</li><li>2 * GT2 idle pulley ID Ø3mm</li><li>1 * GT2 belt (200mm should be enough)</li><li>1 * Spring or elastic band</li><li>1 * LML12B 200mm linear rail</li><li>1 * <a target="_blank" href="https://cnckitchen.store/products/ts100-101-adapter-tips-set-m2-x-m3-m4-m5-m6-1-4-m8-100-lead-and-cadmium-free" rel="nofollow noopener">CNC kitchen Heat Insert Set</a></li><li>Optional :<ul><li>1 * M4x8 Screw</li><li>1 * M4 nut</li></ul></li></ul>Assembling:<ul><li>Insert M3 brass insert (see red arrow below)</li><li>Use M3x8 screw everywhere except 1 * M3x25 (see orange arrow below)</li><li>Use 1 * M3x6 screw to lock the spring or elastic band</li><li>Use 2 M3x25 to mount the GT2 idle pulley</li><li>Insert M5 Nut (see yellow arrow below)</li><li>Make sure to run the belt before assembling the GT2 idle pulley</li><li>Use a small piece of adhesive tape to secure the belt on the arm mount (makes it so much easier to mount the belt on the sliding carriage)</li></ul><figure class="image image_resized" style="width: 79.45%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000430484/design/2024-04-18_86b4fd1a3ef78.png"></figure><figure class="image image_resized" style="width: 35.29%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000430484/design/2024-04-18_75b2c88e1b92e.png"></figure>&nbsp;Print settings:<ul><li>PETG for the soldering iron holder, other part can be printed in PLA</li><li>Layer height : 0.2 mm</li><li>No support</li><li>Print orientation as shown below :</li></ul><figure class="image image_resized" style="width: 54.24%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000430484/design/2024-04-18_75456e3a941b9.jpg"></figure>

Minimalist Heat Insert Press

tools

rostap

<h5>News</h5><ul><li>March 20, 2022 added bigger hook</li><li>March 21, 2022 added USB flash drive holder</li><li>March 21, 2022 added hooks (12mm and 25mm, screwed with M3 screw)</li><li>March 21, 2022 added box (screwed with M4x10 screw)</li><li>March 21, 2022 added 2 wall parts (224x190 and 293x271)</li><li>March 22, 2022 added SD card holder(screwed with M4x10 screw)</li><li>March 22, 2022 added USB flash drive holder (screw in no need)</li><li>March 22, 2022 added box (screw in no need)</li><li>March 24, 2022 added micro SD card holder (for 5 or 20 pieces)</li><li>March 24, 2022 added micro SD card holder (for 5 or 20 pieces)</li><li>April 4, 2022 added shelves (4 dimensions)</li><li>April 6, 2022 Added drawers (found as a <a href="https://www.printables.com/en/model/163008-honeycomb-box-for-honeycomb-wall" rel="nofollow">remix</a>)</li><li>April 12, 2022 Added wrench hooks (2x)</li><li>May 6, 2023 Added more step files</li><li>July 18, 2023 Fixed some stl and step wall files. Added image-diagram how to install your honeycomb</li></ul>Don't forget to look at other <a href="https://www.printables.com/cs/model/152592-honeycomb-storage-wall/remixes" rel="nofollow">remixes</a> - there are a lot of interesting modifications and accessories<a href="https://www.reddit.com/r/honeycombwall/" rel="nofollow">https://www.reddit.com/r/honeycombwall/</a><h3>Honeycomb wall</h3>The basic part of the wall is printable on the Prusa Mini printer. It is necessary to turn off the skirt or set the distance to 1mm in order for the part to fit it on the pad. You can connect the basic parts of the wall together. You can connect it also with printable parts which can be used in various ways (you can use it for screwing to the wall, you can use it as a holder for hanger or as a holder for hook). <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_tisgszo2nt8g.png"></figure>Choose the correct part size for your printer, or use <a href="https://www.printables.com/cs/model/530149-customizable-honeycomb-storage-wall-openscad-v21-b" rel="nofollow">https://www.printables.com/cs/model/530149-customizable-honeycomb-storage-wall-openscad-v21-b</a> for a custom size.<h5><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_frme5d4gs7i6.jpg"></h5><h5> </h5><h5>Diagram to show how to install your honeycomb.</h5><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_yrccc5kolg4d.png"></figure><h5> </h5><h5>Printing settings</h5><ul><li>layer height: 0.25 - 0.3</li><li>perimeters: 3 (or more - without infill for faster printing) </li></ul><h3>Parts for attaching honeycombs to the wall</h3>Some of the parts (which are orange on the picture) you can use for hanging to the wall or for connecting the basic parts together. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_be43o1ws3a92.png"></figure><figure class="table"><table><tbody><tr><td><figure class="image image-style-align-left"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_ajojx36s1wlm.jpg"></figure></td><td><figure class="image image-style-align-left"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_2nxibc3el5li.jpg"></figure></td><td><figure class="image image-style-align-left"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_fqxf6bjpuxz4.jpg"></figure></td></tr></tbody></table></figure>&nbsp;<h3>Fasteners and parts for attaching hooks and objects</h3>There is added one part with the nut (size M3, M4, M5) inside which can be used for screwing whatever holders you want. <figure class="table"><table><tbody><tr><td><figure class="image image-style-align-left"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_1rsdiotho5yk.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_ro3vw4oameqz.png"></figure></td></tr><tr><td><figure class="image image-style-align-left"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_oot6uv6g50m7.png"></figure></td><td><figure class="image image-style-align-left"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_hjjkudqq3rfc.jpg"></figure></td></tr><tr><td><figure class="image image-style-align-left"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_5rje9cxan9um.jpg"></figure></td><td> </td></tr></tbody></table></figure>&nbsp;<h3>Hooks and holders</h3>This is space for new holders and hooks which will be added as needed. Hook bottom and side is prepared to insert to the empty insert part. <figure class="table"><table><tbody><tr><td><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_lcf73emxp801.png"></figure></td><td><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_rtv2d4cr55ea.png"></figure></td></tr><tr><td><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_5nhoo4s4wc6p.png"></figure></td><td> </td></tr><tr><td><figure class="image image-style-align-left"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_fcnuojpuy9qg.jpg"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_ochq2a4i6fyp.jpg"></figure></td></tr><tr><td><figure class="image image-style-align-left"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_nquxdyj69cru.jpg"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_e3jw2h6pd0mm.jpg"></figure></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_avw6edcfzzjq.jpg"></figure></td><td><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_hdrj456s7o1j.jpg"></figure><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_wsokal0vy58z.jpg"></figure></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_en42os2oqu0j.jpg"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_tqjhj78mu78r.jpg"></figure></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_sctwl7slauf5.jpg"></figure></td><td> </td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_6bz02n1vimho.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_qxwzvybnot3t.jpg"></figure>&nbsp;</td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_pa8c7le03qfq.jpg"></figure></td><td> </td></tr></tbody></table></figure>&nbsp;<h3>Other parts</h3>This is cover for the connecting part which is used for hiding the screwer.<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_qmmoju4hk27r.jpg"></figure>And also you can use the second part (as shown in the picture) which can be used for additional attaching the honey comb to the wall. <figure class="table"><table><tbody><tr><td><figure class="image image-style-align-left"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_hnjcfsheftbq.png"></figure></td><td><figure class="image image-style-align-left"><img src="https://makerworld.bblmw.com/makerworld/user/3272831870/draft/2023-09-26_sc318q6f89ef.jpg"></figure></td></tr></tbody></table></figure><h5> </h5><h5>My printing settings for all inserts </h5><ul><li>layer height: 0.2</li><li>perimeters: 4</li><li>infil: 20%</li></ul><h4> </h4>

Honeycomb storage wall

organizeing

Libb_s

Cable organizer

cable org

fznhappy

DJI RC MOUNT FOR BIKE, NEED EXTRAL GO_PRO HOOK and M4 Bolt x 4.After ASSY, It is easy to put DJI RC into it.

DJI RC BIKE MOUNT

bike

hvdzasaur

Furniture set for a complete living / dining room combo. This was part of an old project of mine where I implemented a stripped down version of the MakeItHome furniture arrangement algorithm in a solver in Houdini, these are the individual models used in that project. All models are orientated in their print orientation to be printed without any supports.Tv and Tv_brace would need to be glued together for something more sturdy.Print with 0-5% infill, 2-3 perimeters. Photo is printed at 0.28mm layer height, but for more detail, go finer.Be careful when removing the table and dining chairs from the build plate, the legs are thin and with brittle filament will break off if you're not gentle.

Modern Living Room Furniture - Dollhouse

doll house

3D Print Masters Hub

Simple Storage Bin Containers - Various Sizes & Removable LidsNotes: Please use BRIM if you are having adhesion issues with printer bed.<ul><li>Bin 50mmx50mm</li><li>Bin 50mmx100mm</li><li>Bin 100mmx100mm</li><li>Bin 170mmx170mm</li><li>Please like and subscribe! More to come!</li></ul>🔥🔥 Check out my PRO MODELS HERE! <a target="_blank" href="https://cults3d.com/en/users/FabulousFilaments/3d-models" rel="nofollow noopener">https://cults3d.com/en/users/FabulousFilaments/3d-models</a> 🔥🔥

Simple Storage Bin Containers Various Sizes & Lids

boxes 

agepbiz

<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=jj3vnPYccS4"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/jj3vnPYccS4" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>Simple and clean looking Xbox Controller Standfits 8x3mm anti slip rubber pads (optional)&nbsp;Subscribe or follow me on:Instagram: <a target="_blank" href="https://www.instagram.com/agepbiz/" rel="nofollow noopener">https://www.instagram.com/agepbiz/</a> YouTube: <a target="_blank" href="https://www.youtube.com/user/agepbiz" rel="nofollow noopener">https://www.youtube.com/user/agepbiz</a> Twitter: <a target="_blank" href="https://twitter.com/agepbiz" rel="nofollow noopener">https://twitter.com/agepbiz</a>&nbsp;Printsettings: No raft Support Structures for best results where the rubber pads are 0,1-0,2mm layer height

Minimalistic Xbox Controller Stand

xbox

NeverSum

This is my original design, a hook to attach at the front (long side) or back of the Costco steel wire shelving rack. It fits perfectly and snaps securely in place. It adds extra functionality to your rack. Feedback is greatly appreciated. TIA.

Costco Wire Shelf Hook - front and back

shelfs

Product 1

Convenient Desk/Table Mounted Cup Holder Designed by those who cannot live without being in arms reach of a beverage while working, this cup holder aims to provide an affordable, reliable, and highly compatible alternative to standard commercial offerings. Print Profile Information: This model can support many different approaches to printing-- it's not very particular. However, there are a few recommendations to best ensure an enjoyable experience: The Screw and Clamp pieces should be printed with “strong” profiles. Generally, we achieved this by simply increasing infill to 100%. While a bit over-kill, this ensures the parts do not experience pre-mature failure. <ul><li>The screw, if printed vertically, is especially prone to failure due to layer line orientation. </li><li>The clamp, depending on your print's tolerance, can also experience a strong radial stress when the Cup Holder is slotted in, which may cause stress fractures in the part if it is not strong enough. </li><li>It is not recommended to print any support for the threaded areas in the model. Support in these areas can cause the threads to no longer operate. </li><li>Support Interface material is recommended to ensure a frustration free part cleanup experience. </li></ul>Extra:&nbsp;If you find the cup holder does not have enough grip on the tabletop you are using, you may find cutting a grippy material and applying it to the bottom of the clamp and top of the end cap helpful. Attached you will find the dimensions for these areas (in millimeters): <figure class="image image_resized" style="width:48.89%;"><img src="https://makerworld.bblmw.com/makerworld/draft/400964/2024-01-14_ac327b47e3147.png"><figcaption>Dimensions for Grip Materials</figcaption></figure>

Desk Cup Holder

desk

KG3Dee

Battery dispenser for AA batteries.Push the lever and a battery will be presented.Can hold 26 AA batteries.<ul><li>Adjustable width for smooth, problem-free loading of batteries. The width is critical to prevent fly-out or jams while loading batteries</li><li>Accepts all standard size AA batteries. (≤Ø14.5mm)</li></ul>Please use designer print profiles as these are the only ones that are always up to date.&nbsp;Also, check out this in an <a target="_blank" href="https://makerworld.com/en/models/396440#profileId-297756" rel="nofollow noopener">AAA version</a> and the <a target="_blank" href="https://makerworld.com/en/models/198851#profileId-219450" rel="nofollow noopener">AAA Mechanical Battery Dispenser Slide</a>.&nbsp;Printed model consists of 2 print profiles, “V3 Main Parts” (0.2mm) and “V3 Leveling Parts” (0.15mm).3 plates of parts:<ul><li>Main parts. 0.2mm layer height:<ul><li>Painted 2 color print(2 filament changes). ~5h5m (For one color print, set both filament slots to the same color)</li></ul></li><li>Guide rail. 0.16 layer height. 1 color. ~1h4m</li><li>Leveling knobs. 0.16 layer height. 1 color. ~44m</li></ul>For the leveling knobs I have had success with 0.15mm tolerance, but I have also added an option for 0.2mm.There is a print plate containing test prints to check which is best for you (left one is 0.15mm), as well as separate plates for all knobs with either tolerance.The knob should snap free with minimal force and should have minimal play in the axial direction.Print sequence is by object, as this has given me best results when printing multiple.&nbsp;Assembly:&nbsp;Tools needed:<ul><li>Flat head screwdriver ~3.5mm.</li></ul>During assembly always check rotational freedom of the lever after each step. If it binds, check if the printed parts are smooth. Cut away any faults in the print.&nbsp;1.<ul><li>Insert the lever in the casing. There is a slotted hole in the casing which needs to line up with the lever pin. Push to insert, and rotate multiple times both ways until the rotation is more or less friction free.</li><li>Repeat steps above for the other side.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/771614/2024-02-11_39cb8ba348c5c.png"></figure><figure class="image image_resized" style="width:16.69%;"><img src="https://makerworld.bblmw.com/makerworld/draft/771614/2024-02-16_696d5b597a4e5.gif"></figure>&nbsp;2.<ul><li>Insert the inner stoppers on both casings, protruding inside the lever groove, and insert the mid plate. The plate will keep the stoppers locked in place.</li><li>Do the same for the front stoppers, and insert the front plate.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/771614/2024-02-11_5da3f8c4a6d3c.png"></figure>3.<ul><li>Insert the handle. Check that the handle can move freely up and down.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/771614/2024-02-11_03b3c1c458c53.png"></figure>4.<ul><li>Insert the springs. They should be inserted as shown in the pictures, with the pin at the lowest point.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/771614/2024-02-12_28498c0d0830b.png"></figure><ul><li>Tension the springs and put the pin in the lever.</li><li>Insert the lower stiffener (Top in below picture).</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/771614/2024-02-12_7320db61e4d09.png"></figure><ul><li>Insert spring guides as shown. The flat one is friction fit into the cut-outs on the mid plate. The spring center one is dove-tailed.</li><li>Check the handle movement after this step, make sure it moves to its end (top) position by itself.</li></ul>5.<ul><li>Check the quality of the threaded bolt.</li><li>Use the printed tool to hold the leveling knob. Rest the bolt against a table and carefully, with no excessive force, turn the screw while holding the tool until it snaps free. Once free there should be minimal play in the axial direction. Do this for all knobs. If the knob is stuck, try the 0.2mm tolerance version.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/771614/2024-02-12_411dce1e012b4.png"></figure><ul><li>Trial fit the knob bolts in the guide rail threads. There might be some initial friction here, so enter the threads and turn a few degrees, then back again, then gradually increasing the turn for each go back and forth until the thread is completely set. Be patient here, don't use excessive force.</li></ul>6.<ul><li>Push in the leveling knobs in the casing. There is a slot in the knob and in the casing that should match up.</li><li>Use the printed tool, and twist the knob clock-wise until it sets. No need to overtighten. For the lower one you have to push the handle down to gain access.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/771614/2024-03-17_5afc523ed3444.png"></figure><ul><li>Insert the guiderail on the opposite side of the casing, and screw in the bolts. Do a couple of turns for all, then go back and gradually tighten in multiple goes until all bolts are seated. The guiderail and its position is what keeps the batteries rolling smoothly down when loading the dispenser. Too wide and the batteries will fly out, too narrow and the batteries will jam.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/771614/2024-02-12_7ac74cca77c45.png"></figure>7.<ul><li>Final step is to install the last 2 stiffeners.</li></ul>&nbsp;Width adjustment:<ul><li>To widen the gap, turn the bolt clock-wise.</li><li>To narrow the gap, turn the bolt counter-clock-wise.</li><li>Start by turning all the bolts on full turn counter-clock-wise.</li><li>Grab your battery and insert it in the dispenser and hold it in front of the leveling knob. Adjust the knob so there is minimal play in the battery's axial direction. Continue this for all knobs.</li><li>Once done, release the battery from the top and observe its rolling down the slide. Adjust where necessary and your done.</li></ul>&nbsp;&nbsp;I advice using the original (designer) profiles, as these always have the latest changes incorporated.&nbsp;Would appreciate some feedback if this dispenser works with your batteries, or if you have any issues.&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;

AA Mechanical Battery Dispenser

battery

Super_Laserkatz

Moin, ich habe einen wall planter designt, der völlig ohne Stützmaterialien gedruckt werden kann und ca. 200g Filament verschlingt. Auf meinem A1 passen alle Toleranzen wunderbar. Ich werde in Zukunft noch weitere Vasen nach diesem System anfertigen, also bleib auf dem Laufenden!Wenn du Verbesserungsvorschläge hast, lass es mich wissen ;)&nbsp;<figure class="media"><div data-oembed-url="https://youtube.com/shorts/xP6KkuAtk3o?feature=share"><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=xP6KkuAtk3o"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://www.youtube.com/embed/xP6KkuAtk3o" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>&nbsp;https://www.tiktok.com/@super...laserkatz/video/7328477062619090209?is_from_webapp=1&sender_device=pc&web_id=7286367789157090849

Wall Planter 1.8

plants

arculated

Kocyns

Thanks for video: @marsgizmo (ytb)<h4>PRINT SETTINGS</h4><ul><li>Height: 100 mm</li><li>Recommended material is PLA and layer 0,12mm</li><li>Minimal scale 75%!</li><li>Optimized model for printing without support!</li></ul><h4>Remix: <a target="_blank" href="https://makerworld.com/en/models/173902#profileId-191118" rel="nofollow noopener">Heart for Rose Bear</a></h4><figure class="image image_resized" style="width: 40.76%"><a href="https://makerworld.com/en/models/173902#profileId-191118" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000152175/design/2024-02-06_bdaecc3a4c139.png"></a></figure>&nbsp;If you want permission for commercial use: <a target="_blank" href="https://www.patreon.com/kocy/" rel="nofollow noopener">patreon.com/Kocy</a>

Rose Bear

Valentine's

garrettalansmith

Introducing the Bow Style Sander – your tool for delicate project polishing! This sleek bow ensures swift and efficient finishes on all your creations.&nbsp;What You'll Need:<ul><li>Sandpaper</li><li>Four (4) M3 x 8mm Screws (Thanks <a target="_blank" href="https://makerworld.com/en/u/41849858" rel="nofollow noopener">nimmesota_3D</a> for the hardware update!)</li><li>Your masterpiece in need of a softer sandpaper touch</li><li>A dash of patience</li></ul>Simple Installation: Squeeze the bow during sandpaper installation for just the right tension. Experiment with the squeeze for different effects – soft for highly curved surfaces, tight for use like a sanding sponge.Gently poke the holes with an Allen wrench to kickstart the screws. The design ingeniously uses sandpaper as friction, ensuring a snug fit without over-tightening. Versatile Design: Explore the small flats on either side for flashing lines or areas requiring more rigidity behind the sandpaper. The corners are perfect for tackling those tricky, hard-to-reach spots, too – no need to change tools as frequently.&nbsp;Latest Update - 12.30.23: New sandpaper templates in different widths, a suggestion from nimmesota_3D. The new 20mm, 10mm, and 5mm templates are available <a target="_blank" href="https://makerworld.com/en/models/115868#profileId-124528" rel="nofollow noopener">here</a>!.Check out my other FREE models <a target="_blank" href="https://makerworld.com/en/u/4019373707" rel="nofollow noopener">here</a>!

Sanding Bow

sanding 

hYPERfOCUS

Do you want your office chair to sit still and stop rolling? Have I got the solution for you! Office chair castor locks, never roll anywhere again!

Office Chair Castor Locks

braga3dprint

The 3D model of a lightbox featuring the Bambu Lab logo is the perfect accessory for fans of this outstanding 3D printer brand. Crafted with precision, it displays the Bambu Lab logo in all its glory. This lightbox is not just a decorative piece; it's a clever integration of art and technology. With a USB LED, you can effortlessly plug it into the USB port conveniently located behind your printer's screen. The magic happens when you power up your printer, as the lightbox illuminates in harmony with your machine. This practical and aesthetically pleasing addition is an excellent way to celebrate your passion for 3D printing and Bambu Lab. Elevate your workspace with this innovative accessory! 🖨️✨ If you don't have or don't want to install LED's you can just glue the parts together and have an awesome sign!&nbsp;Materials and tools: - glue gun - aluminum tape - led strip (here is the one I <a target="_blank" href="https://pt.aliexpress.com/item/1005004253095880.html?spm=a2g0o.order_list.order_list_main.16.1df1caa45b098E&gatewayAdapt=glo2bra" rel="nofollow noopener">use</a>): simple 1m white led USB- soldering iron (optional)&nbsp;RECOMMENDATIONS- use a textured PEI sheet - use the print profile, it has quite a few setting changes that help achieve the best results - make a hole for the USB strip wherever you like it best with a soldering iron, drill or in the slicer- use the aluminum tape on the inside of the backplate to help with light diffusion - glue the LED's the further away from the colored design possible; placing them too close ruins the diffusion and the individual LED's become visible Bambu Studio Settings: I always recommend using the print profile I provided since it has settings with which I've been able to get the best results. If you choose not to here are the main slicer settings I recommend: - preferences (ctrl + P) → activate developer settings → Quality →Advanced → First Layer Flow Ratio: 1.04 - Quality → Wall generator → Arachne - Quality → Wall transitioning threshold angle → 50º - Strength → Advanced → Infill/wall overlap → 20% - Quality → Advanced → Avoid crossing walls - Increasing retraction / reducing temperature can help reducing wisps - Order color printing from lightest to darkest color&nbsp;How to install on the printer: <figure class="media"><div data-oembed-url="https://www.youtube.com/shorts/OiY5v5AX7Ek"><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=OiY5v5AX7Ek"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://www.youtube.com/embed/OiY5v5AX7Ek" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure> How to make a hole in Bambu Studio:<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=OsA23WCxRtg"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/OsA23WCxRtg" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure> Assembly video: <figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=QNsShLmXYh0"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/QNsShLmXYh0" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

Bambu Lab Lightbox LED Lamp

signs

paint

AMT_MW

<h2>What it is</h2>A four digit life counter with a small compartment inside, a screw on lid and detents for the number positions.It is part of a design family, so you do have a few options if you want it a bit different:<figure class="table"><table><tbody><tr><td>2 wheels</td><td><a target="_blank" href="https://makerworld.com/models/136387#profileId-148336" rel="nofollow noopener">3 wheels</a></td><td><a target="_blank" href="https://makerworld.com/models/136390#profileId-148342" rel="nofollow noopener">4 wheels</a></td></tr><tr><td><figure class="image image_resized" style="width:62.74%;"><img src="https://makerworld.bblmw.com/makerworld/draft/394742/2024-01-08_c088fc921dfab.jpg"></figure></td><td><figure class="image image_resized" style="width:50.05%;"><a href="https://makerworld.com/models/136387#profileId-148336" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/394742/2024-01-08_547b5c0ced69c.jpg"></a></figure></td><td><figure class="image image_resized" style="width:66.09%;"><a href="https://makerworld.com/models/136390#profileId-148342" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/394742/2024-01-08_692abd2283447.jpg"></a></figure></td></tr><tr><td>You are here :)</td><td><a target="_blank" href="https://makerworld.com/models/136387#profileId-148336" rel="nofollow noopener">Life Counter 0-999</a></td><td><a target="_blank" href="https://makerworld.com/models/136390#profileId-148342" rel="nofollow noopener">Life Counter 0-9999</a></td></tr></tbody></table></figure><h2>How to print</h2>For multicolor printing and convinience, a 3MF file is provided. There are several modifiers present, deactivate or change them to get your desired outcome.<figure class="image"><img src="https://media.printables.com/media/prints/709800/rich_content/a39f2575-9bcd-4dff-85f3-781f92a7e9df/thumbs/cover/800x222/png/image.webp"></figure>Recommended for printing is a layer height of 0.16mm and a 0.4 mm nozzle, but up to a layer height of 0.2mm and a 0.6mm nozzle the results have been surprisingly good as well.&nbsp;The optional text on the lid or Axle (like HP & XP) simply is added via the text shape tool of the slicer. Any font you have installed is possible.<figure class="image"><img src="https://media.printables.com/media/prints/709800/rich_content/dc4dd686-4908-4a4f-95a4-5a1a2b5d0e0f/thumbs/inside/1920x1440/png/image.webp"></figure>Material at one's discretion, I opted for PETG and 25% infill.Scaling it down is possible, smaller than 60% and the tolerances may be become a problem.<h2>Without MMU or AMS</h2>If not already printed as multicolor, nail polish or model paint works well to highlight the glyphs. For text on the axle or lid a manual filament swap is advised, using the text shape tool to emboss your text may also be an option.<h2>What next</h2>There may be improvements and modifications based on feedback given here.Maybe, take a look at <a target="_blank" href="https://makerworld.com/u/2797532051" rel="nofollow noopener">my other designs</a> ;-)

Life Counter 0-99

life counter

Aruba3D

A simple gift paper cutter, you only need a #11 blade and insert in the right position

Wrapping paper cutter / Gift wrap

xmas

ruimach

<div><h1>Summary</h1><div>This is a Sink Organizer for the kitchen.The goal was to make a robust model, with a open bottom to allow for water to flow. The Hexagon shape for the holes was a easy design choice :)Updated 13/01/2023: Added a side top area.Updated 2: 16/01/2023: Added to parts to make a small hanger to dry the dish cloth. A Hexagonal Peg and a small rod. I didn't need glue to attach the pegs and the rod.<iframe src="https://www.youtube.com/embed/7J1vgCdTl0E" title="YouTube video player" frameborder="0" allowfullscreen="allowfullscreen"></iframe>Printing instructions:Material: PLA or PTEG (or similar…) Layer Height: .2 Infill: 15% Walls: 3 for extra strenght Supports: Yes Change filament during print: Not needed Brim: Recommended Raft: No All models are print ready oriented.Assembly:Just slide the side in the bucket. Some force may be needed. No glue is required.And that's it! I hope it fits your needs!Ps: If you like this model and want to support me in a simple way, like, download and share this model with your friends. If you make one I would love to see yours, please share your make.</div><h1>Print Settings</h1>Printer: <div>Bambulab X1C</div> <pre><code> Rafts: <div>No</div></code></pre> Supports: <div>Yes</div> <pre><code> Resolution: <div>.2</div></code></pre> Infill: <div>15</div> <pre><code> Filament: <a href="http://www.amazon.com/s?url=search-alias&field-keywords=Any+PLA" target="_blank" rel="nofollow noopener"> Any PLA </a> Any</code></pre></div>

Kitchen Sink Organizer

house

IndomReps

Ryobi One+ Battery and Tool mounts&nbsp;I mainly designed these for the battery mounts which work really well and developed some mounts for the tools as well. Unfortunately due to Ryobi's tool design making something that was universal for their whole tool ecosystem isn't easy but came up with a few options that will work for some tools.&nbsp;All models use #8 screws for mounting them into whatever material you want.&nbsp;Print Settings & Material:for these functional parts I typically use atleast 5 perimeter walls and 30% or higher infill depending on your preferred pattern. The .3mf project file has the prints loaded and orientated how I would recommend printing them for appearance and strength. The battery mount and the underhung tool mount are fine to be printed in Pro PLA or even regular PLA as ABS and PETG are probably overkill for that part. The tool mounts however especially the flat and angled one should be printed in either Pro PLA or ABS.&nbsp;Model Specific Info:&nbsp;Battery Mount:Everything is pretty straight forward for this model, just decide if you want to add supports for the locking tabs. Fits the 18v One+ batteries&nbsp;Angled Tool Mount:Confirmed this works for the drill tool and will probably work for other tools that are similar. The 3mf file has this part orientated how I would print it. Requires a decent amount of support material to be used and the underside isn't super pretty looking, but the part is much stronger when printed in this orientation.&nbsp;Flat Tool Mount:Confirmed this works for the drill tool and will probably work for other tools that are similar. .3mf file doesn't have the most ideal orientation for strength but a lot more reliable to print. You can try to print in a similar orientation as the angled mount just make sure your settings and bed adhesion are on point.&nbsp;Underhung Mount:The underhung mount is to be mounted on the underside of any surface like a workbench or cabinet and the battery end of the tool slides into it like its a shoe. Its a more universal option but you are limited in how you attach the mount. Print it in the orientation of the .3mf file and no supports are needed.

Ryobi ONE+ Power Tool & Battery Mounts

raptordemon

needed a holder for bambu nozzle holder for gridfinity but i needed something that was for a full hot end and fan + sock and wires.&nbsp;the tall one is stackable the short one is not.

Gridfinity holder for Complete/Assembled Bambu Nozzle / Hotend

gridfinity

mcgybeer

Cute Mini Octopus, the original!It's designed so it can be printed at once. No assembly or supports required.Spare tentacle available as well, no need to discard failed prints!

Cute Mini Octopus

figurines

flexi.factory

This Flexi Panda is an articulated print-in-place model that needs NO supports. The stand is printed in 3 parts and easily snaps together with no need for glue Included are 7 files: -Panda -Bamboo stick (for panda to hold) -Stand Platform -Stand Base -Stand ladder -Painted Bambu AMS Panda -Painted Bambu AMS Stand Also Optimized for AMS, meaning if you are using a Bambu Printer with multiple colors, you should easily be able to use the fill tool for coloring. I have added a 3mf as well for convenience! Like with all my Flexi's, I went through many iterations to make sure it was strong, and easy to print without supports. ALL Flexi Factory designs are protected by Copyright Law. When you purchase, you do NOT have the right to sell any digital file or printed model of my designs without my explicit written consent.To legally sell PRINTED models, you may obtain my permission through this link:<a target="_blank" href="https://www.patreon.com/FlexiFactory" rel="nofollow noopener">https://www.patreon.com/FlexiFactory</a> or www.myminifactory.com/users/FlexiFactoryPlease help support the creative work of each 3D artist and NEVER share or sell a digital file.<h2>3D PRINTING SETTINGS</h2>Easy Print. Can be scaled upNo Supports (adding supports will hinder functionality) Mostly Print-in-place (the stand snaps together) 15% infill I always like to use 3 walls PLA works great

Flexi Factory and Bambu Lab Collaborative: Panda Bear and Stand

toys

RainerBavaria

i designed a Buildplate-holder for 7 Plates , designed in Stairs so you can see the front of every plate for reading or seeing the desing.&nbsp;I designed in 2 parts so it fits on the printbed at once.i desinged conectors as well , i did not need any glue for fitting it .i printed standing on the Bambu-Logo→ less filament changes ,also then is no support needed.printed in 0.20 layers , 2 perimeters , 3Bottom/Top.i did a pause before th toplayers and fill some steelballs in for some wight, so i used grid-infill 10%.&nbsp;&nbsp;

phone

tools

organizeing

cable org

bike

doll house

boxes

xbox

shelfs

desk

battery

plants

arculated

Valentine's

sanding

vr

signs

paint

life counter

xmas

house

tools

gridfinity

figurines

toys

bamboo labs