dnsmayhem

DGs 3D-PRINT

Das ist ein Schleifkeil zum schleifen von klein und großen Bauteilen.16 Schleifkeile von XS-L in verschieden BreitenDer Schleifkeil ist relativ simpel aufgebaut. Man legt das Schleifpapier um den Grundkörper herum und keilt es mit dem Keil ein.Beim festziehen der Schraube wird das Schleifpapier straff gezogen.Zusätzlich gebt es ein kleine Werkzeug zum lösen und festschrauben der Schraube&nbsp;-Ich empfehle grundsätzlich PETG für mechanische Teile.-Grundkörper und Keil sind in PLA kein Problem.-Die Schraube ist ein mechanisches Teil.-In meinem Test war die Schraube in PLA+ stabil genug -Wenn es Problem mit der Haltbarkeit der Schraube gibt sollte man PETG verwenden&nbsp;Größe XS12,5mm Breite, 68mm Lange, Schleifpapierstreifen 150mm Lange15,0mm Breite, 68mm Lange, Schleifpapierstreifen 150mm Lange20,0mm Breite, 68mm Lange, Schleifpapierstreifen 150mm Lange25,0mm Breite, 68mm Lange, Schleifpapierstreifen 150mm Lange&nbsp;Größe S19,0mm Breite, 101mm Lange, Schleifpapierstreifen 220mm Lange22,5mm Breite, 101mm Lange, Schleifpapierstreifen 220mm Lange30,0mm Breite, 101mm Lange, Schleifpapierstreifen 220mm Lange37,5mm Breite, 101mm Lange, Schleifpapierstreifen 220mm Lange&nbsp;Größe M25,0mm Breite, 135mm Lange, Schleifpapierstreifen 295mm Lange30,0mm Breite, 135mm Lange, Schleifpapierstreifen 295mm Lange40,0mm Breite, 135mm Lange, Schleifpapierstreifen 295mm Lange50,0mm Breite, 135mm Lange, Schleifpapierstreifen 295mm Lange&nbsp;Größe L31,0mm Breite, 168mm Lange, Schleifpapierstreifen 370mm Lange37,5mm Breite, 168mm Lange, Schleifpapierstreifen 370mm Lange50,0mm Breite, 168mm Lange, Schleifpapierstreifen 370mm Lange62,5mm Breite, 168mm Lange, Schleifpapierstreifen 370mm Lange

Schleifkeil in 16 Größen von XS-L (Schleifklotz)

Shop Things

SavageLau

I am having issue with put my build plate on my A1.The original guide does help aling the build plate, but I feel like those two on the side does not help that well, since it is so low to the printer bed. So I made this build plate aligner deisgn to help easier put you build plate down.&nbsp;Due to the nozzle prime brush located on the left, and nozzle have travel a lot of the left, I don't think it worth the risk to put anything on the left. Plus, this one on the right side is already good enough to help you locate the build build.&nbsp;It cost very little filament, less than 5g. Around 19m printing time. Suggests print at least with PETG, or ABS.&nbsp;&nbsp;<h2>ATTENTION! If you are firmware version 01.01.50.24 or above, do not use other people's printing profile, model is not longer compare after firmware update. </h2>&nbsp;<h2>Update 1/27/2024: New model updated, name “for 01.01.50.24 firmware”. </h2><h3>New firmware version: 01.01.50.24(beta) will cause issue. I have found nozzle clumping detection cause the issue. It is automatically enabled after firmware update. But no option to disable it currently. More information from Bambu Wiki: </h3><h3><a target="_blank" href="https://wiki.bambulab.com/en/a1-mini/manual/nozzle-warp-detection" rel="nofollow noopener">https://wiki.bambulab.com/en/a1-mini/manual/nozzle-warp-detection</a> </h3>&nbsp;<h3>Issue description: </h3>After update firmware 0.1.01.50.24. Print stops randomly in the middle and error note shows: <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461583/2024-01-27_271f7f17e33c4.png"></figure> Nozzle will park on the aliger area and cuase issue. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461583/2024-01-27_b0eecdf4e5003.png"></figure> According to BBL Wiki: "1. After printing all the walls of the first object on the third layer of this plate, the tool head will move to the position of the purge wiper for the first detection. The specific coordinates of the nozzle during detection:  A1 mini (X-6, Y 170, Z-1); A1 (X 261, Y 250, Z-1). The detection process is shown in the following figure. " &nbsp;<h2>Install guide:</h2>Align from the back, push the aligner pin into the bolt hole under the build plate.Confrim top part is all the way in.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461583/2024-01-04_7cd7e48eb7b47.gif"></figure>&nbsp;&nbsp;Many revisions was made and many tests was done to confirm it not only works but also get good fit and finish:<figure class="image image_resized" style="width:55%;"><img src="https://makerworld.bblmw.com/makerworld/draft/461583/2024-01-05_2c006911bca8.jpg"></figure>&nbsp;<h2>Material:</h2>Highly suggest to print with ABS or better heat resistant material. PETG Will works. PLA is not recommaned.I also made cut line design on alginer, those cut slots should help guiding the direction when thermal expansion and retraction happen. Which it should bond on the printer bed more if thermal deformation occurs.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461583/2024-01-04_ec38222ff07b3.png"></figure>

A1 Build Plate Aligner

Printer Accessories

IdeenDüse

Ich habe das neue PETG Transluzent Filament von BambuLab ausgetestet. Dafür habe ich eine Kristalllampe designed, da ich finde, dass Kristalle gut mit dem Filament zur Geltung kommen und es authentisch aussieht. Ich habe alle Teile auf meinem BambuLab X1C gedruckt und die Textured PEI plate von BambuLab verwendet.&nbsp;Hier ist der Amazon Affiliate Link zum passenden LED-Stripe: <a target="_blank" href="https://amzn.to/42Lkp0D" rel="nofollow noopener">https://amzn.to/42Lkp0D</a>&nbsp;NEU!!!!Wenn man sich eine Kristallampe baut, hat man noch LED-Streifen übrig, aber kein Steuergerät und Fernbedienung mehr, um sich weitere bauen zu können.Ich habe beim Verkäufer angefragt, ob man Steuergerät und Fernbedienung ohne LED-Streifen bestellen kann, leider war dies nicht möglich.Also habe ich nach einer Kompatiblen Lösung gesucht und etwas passendes gefunden. Ein einfache Möglichkeit den Restlichen LED-Steifen zu Lampen zu verarbeiten. Die Anleitung stelle ich hier als PDF zur Verfügung. &nbsp;Um meine Arbeit kostenfrei zu Unterstützen, würde ich mich freuen wenn ihr die Affiliate Links zum Kauf der benötigten Bauteile verwendet:&nbsp;Passendes Steuergerät mit Fernbedienung:     <a target="_blank" href="https://amzn.to/49AyTDd" rel="nofollow noopener">https://amzn.to/49AyTDd</a>Netzteil:                                                                   <a target="_blank" href="https://amzn.to/49SAowk" rel="nofollow noopener">https://amzn.to/49SAowk</a>&nbsp;Hier geht es zum Bauanleitungs Video:&nbsp;<figure class="media"></figure>&nbsp;I tested the new translucent filament from BambuLab.I designed a crystal lamp for this because I think that crystals show off well with the filament and it looks authentic.I printed all the parts on my BambuLab X1C and used BambuLab&#39;s Textured PEI plate.you need no Support.&nbsp;Here is the Amazon affiliate link to the matching LED strip   : <a target="_blank" href="https://amzn.to/42Lkp0D" rel="nofollow noopener">https://amzn.to/42Lkp0D</a>&nbsp;NEW!!!! If you build a crystal lamp, you still have LED strips left, but no control unit or remote control to be able to build more. I asked the seller whether it was possible to order the control unit and remote control without LED strips, unfortunately this was not possible. So I looked for a compatible solution and found something suitable. A simple way to process the remaining LED strips into lamps. I provide the instructions here as a PDF.&nbsp;In order to support my work free of charge, I would be happy if you use the affiliate links to purchase the components you need:&nbsp;Suitable control device with remote control:       <a target="_blank" href="https://amzn.to/49AyTDd" rel="nofollow noopener">https://amzn.to/49AyTDd</a>Power supply:                                                             <a target="_blank" href="https://amzn.to/49SAowk" rel="nofollow noopener">https://amzn.to/49SAowk</a>&nbsp;&nbsp;  &nbsp;&nbsp;&nbsp;

Kristalllampe /Crystal lamp

Lamps/Lights

erer2001

Mount four 3.5 inch hdd on a 140 mm fan mount. The extra 8 holes are for stability and works on Coolermaster Q300L and Q500L cases.Ender 3 v20.6 nozzlePETGCategory: Computer

4x 3.5 inch hard drive cage on 140 mm fan mount (Extra holes for Masterbox Q300L/Q500L)

Electronics Enclosures

goldenp

Voronoi LED lamp shade. Not to be illuminated by fire.<h3>Print Settings</h3>Printer Brand:BambuLabPrinter: MakerBot Replicator 2Rafts:NoSupports: NoResolution:.24Infill: 20%&nbsp;&nbsp;&nbsp;Category: Decor

Voronoi LED mushroom cap tealight shade

Cool Things

Jerryie

Remixed cute fox from Thingiverse. Easy printable&nbsp;

Low poly fox

Cute Things

GCprint

Book page holder

Useful Things

3D design shop

After a long journey, I've finally completed my flexible skeleton dragon.&nbsp;It's a fun piece of toy that's incredibly flexible, with virtually all joints capable of movement. It has become a huge hit with the kids at home!&nbsp;I printed it on a smooth surface, which eliminates potential issues with adhesion on a textured bed. If adhesion problems persist, I recommend adding a brim.&nbsp;Improved version