djflizo69

Stamatis Sarlis

Disclaimer: This is not an original Apple product apparently. It is just a case for my Apple Pencil 2/Pro that I made a while ago.&nbsp;You will need 5 neodymium magnets size 8mmx2mm (8mm diameter). Correct size is very important for case snap so please measure the magnets before proceed.*** Note ***Depending on the power of the magnets you can have a easily or harder to remove top cover. There is always an easy way to remove the top part. See the video on the end to find out how!!!&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_e1dc5e752623c.jpeg"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_4b6304c96e14e8.jpeg">&nbsp;I use these magnets from Amazon but any 8mmx2mm magnets should fit.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_a0501a9dccfe38.jpeg">&nbsp;<h3>Bottom part of the case assembly</h3>Print the bottom part of the case. Take on of the magnets and place it around 6cm away from the top of the pencil (see below). Switch the magnet side if required so to be in the right distance.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_05f4d80c91cd1.jpeg">&nbsp;Put the Pencil inside the case, align it with the magnet and push it so for the magnet to be placed inside the hole.&nbsp;<figure class="image image_resized" style="width: 88.4%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_7f4806fab3dbc8.jpeg"><figcaption>Press so the magnet placed in the hole of the case</figcaption></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_6c1a195eac47d8.jpeg"><figcaption>Final placement of the Pencil magnet</figcaption></figure>Now put a drop of instant glue in the 2 remaining holes of the bottom part as per images below:&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_8ac5bf280cd0e8.jpeg"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_6d516dbdb7144.jpeg">&nbsp;*** Very important ***Place the magnets with the same direction of polarity in the holes. Their poles should be aligned (same poles should point to the top of the case).Press them enough so to have a small gap between the top of the plastic and the magnet. The gap is just a tiny one but it is very important to be there.Leave the glue to stick for 10 minutes.&nbsp;<h3>Top part of the case assembly</h3>Place the remaining 2 magnets on the bottom case, on top of the already placed magnets as per images below:<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_a059d46af93628.jpeg"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_149b4b049db5d8.jpeg">&nbsp;Put just a drop of instant glue on the 2 holes for the magnets in top part of the case as per images:<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_a9e39a3d233fa8.jpeg"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_6b6ddb3dc85578.jpeg">&nbsp;Align the top case with the bottom as per image:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_946c10bb6cb8c8.jpeg"></figure>Press the top part against the bottom part so the magnets fit in place on the top part.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000128721/design/2024-01-07_86b0e93c8bf77.jpeg"></figure>Remove the top part and press with your fingers the 2 magnets again so to take their final place.Leave the glue to stick for 10 minutes.&nbsp;Enjoy your magnetic Apple Pencil 2 case!!! See the video below on how to open the case easily :-)&nbsp;<figure class="media"><oembed url="https://www.youtube.com/watch?v=Ua9XDDlaU0Q"></oembed></figure>&nbsp;

Apple Pencil 2/Pro magnetic case

Things I want print

3DPODesigns

After starting to delve deep into the hobby of 3D printing, I realized magnets are fairly frequently used. After I purchased some that came all stuck together in a single plastic box, I designed this. It's nothing special, but hopefully someone can use it.&nbsp;The lid slides from top down and may take a couple of ins and outs before it'll slide in smoothly as it was sized to fit nearly perfectly.&nbsp;Model in photos was printed with Hatchbox Matte Grey PLA.Both lid/case oriented flat side down with no supports. My slicer (bambu) suggested supports for the numbers, but I had no issues with the overhangs on my Bambu P1P. Your experience may vary.&nbsp;Note: If there are any other commonly used sizes of magnets that you think should be added to the design, let me know.

Magnet Organizer

Magnet box

Eminent3D

Socket trays i made for my sockets. Sockets varry by brand so cant garentee they will fit yours. included stl for modifying the files to fit your sizes as needed. There are Metric 3/8" drive for 10-19, Metric ¼" from 5-14 and SAE 3/8" drive.You can change the color out in the last 4 layers to make the bottom color POP and quickly display which color is missing as seen in pictures.

Things I want print

Magnet box

Tool holders