darkmajin

trynottobreakanything

This is the Gear Rhombo Junior (Jr.) (the Spirit of Mini Gear Sphere). This is totally redesigned from the Gear Sphere by TNTBA. This Gear fidget toy is a lot of fun and is now portable.Approximate size of this design is: 50mmx50mmx50mm.&nbsp;This is the Free version of the <a target="_blank" href="https://thangs.com/designer/trynottobreakanything/3d-model/Gear%20Rhombo%20JR%20by%20TNTBA-1087166" rel="nofollow noopener">Gear Rhombo JR which I&#39;ve licensed for those who wish to sell and print.</a> &nbsp;The time to print and fully assemble is approximately 1 hour and 15-30 minutes.&nbsp;Gears and core may be printed in any material. Clips were designed to be printed in PETG. Tool can be printed in PLA.&nbsp;Place the clip into the tool and use the tool to place the clips directly into the holes on the core. Make sure you go directly into the hole to avoid splitting, breaking, or over-bending the clips. I would recommend that you print out additional clips to ensure you have extras when you mess up.&nbsp;Once the clips are installed, you can place the gears following the numbering located on each gear and core side.&nbsp;The mechanism to move this toy fidget was inspired by <a target="_blank" href="https://thangs.com/designer/RuvenBals/3d-model/Gear%20Ball-1069853" rel="nofollow noopener">RuvenBals&#39; Gear Ball </a>and <a target="_blank" href="https://www.thingiverse.com/thing:10483" rel="nofollow noopener">Emmett&#39;s Gear Cube</a>.&nbsp;Enjoy!

Gear Rhombo JR by TNTBA (Free Version)

killbill

Sorghak

Do you want your children to think you are a wizard? Do you want to show something interesting at a party?Follow these simple steps to perform the magic trick:<ol><li>Prepare the cup: Fill the cup with water and let it sit for a minute.</li><li>Refill and conceal: Fill the cup with water again, and then cover the small hole on the outside of the cup with your finger.</li><li>Pour out the water: Carefully pour out the water from the inside of the cup.</li><li>Cast the spell: Say the magic word, &#34;Aguamenti!&#34;</li><li>Release the magic: Remove your finger from the hole to let air in.</li><li>Behold the wonder: Watch in amazement as the cup magically refills itself!</li></ol>Pro Tip: For an extra touch of mystery, print these instructions on non-uniform or dark material to keep the secret hidden!

A self-filling cup / Magic Goblet

wizardry contest

amorosoedoardo

This 3d printed bag is one of my favorite designs! With its rippling lines, it reminds me of the wave motion of the Mediterranean coastline. From this inspiration in fact it gets its name “CRESTA” precisely from the crest of the waves. The numerous presence of holes allows you to play with different handle configurations and also makes it very easy to accessorize it.To enable a perfect attachment between the handle and the bag bucket, you need to get something suitable to be passed through the holes provided. I suggest you opt for round snap hooks (28mm diameter) or any kind of rope and/or lace.Edoardo, xoxo

Cresta 3d bag 

Praus8577

Birthday Crown printed for my niece. Used Sunlu Rainbow PLA

Birthday Crown

urodziny

hofflab

<h2>Simple A1mini Cable Chain for Heatbed. (A1mini ready, ≈ 40g)</h2>&nbsp;Only 16 chain links and 15 lids are required, but I added 18 of both as they do not require much filament. Sometimes, little adhesion problems will ruin the look and functionality of a chain link or lid.&nbsp;Removing  supports of the bed anchor can be quite tricky and will require some form of tweezers!&nbsp;Installation:<ol><li>First install the base and bed anchor, which should fit perfectly (don&#39;t worry too much about the cables, as they will fit into place “automatically”).</li><li>Attach 16 links to each other and both anchors. (The open side should face “inside”. See my pictures). The links could also be attached one by one with alternating “openings”, I just did not like the look of it. Try it out and decide for yourself.</li><li>Push the bed back as far as possible for easy installation of the lids. Because of their size they are quite fragile so be careful while installing or disassembly.</li></ol>If you encounter any problems or got ideas for improvement just massage me in the DMs.

A1 mini Heatbed Cable Chain

Jackalolz

<h3>Build the beacon in your base and enjoy the boosts!</h3>Say hello to the LED Minecraft Beacon Lamp. This wonderful model is roughly an 8x scale with a little interpretation for the glass enclosure. Modelled around the LED Lamp Kit found in the Bambu store, I&#39;ve added an insert to support an LED strip with a controller. Both options for illumination are supported&nbsp;This is a very simple build and is printable even on the A1 Mini. This model consists of 7 plates pushing together with their joins. All press joins have a tolerance of 0.1mm which I was able to achieve with my A1. No screws or glue required during construction. If you want to have the beacon attached upside down or horizontally I would consider glue. Updates: 07/06/24 - Added new beacon shell option; Minecraft sword air vent in beacon shell to expel heat when using WLED illumination. Added more depth to WLED Insert for cables and modules.<h4>Materials &amp; Filament:</h4>For the model seen above I&#39;ve used;<ul><li>PLA White for the glass enclosure</li><li>PLA Sparkle for the obsidian base</li><li>PTEG Transparent for the beacon shell.</li></ul>The base and glass enclosure were printed using the 0.4 nozzle, however, the PTEG shell was printed at 0.6 nozzle. PTEG transparent can be printed with a smaller nozzle, seek Bambu Labs tips on printing PTEG transparent filament. I have not tested printing the shell in generic PLA, however after running a transparent test, I can&#39;t see it working with anything that isn&#39;t transparent.<h4>Construction:</h4><figure class="image image_resized" style="width: 80%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486391/design/2024-06-06_a7370299025f18.png"></figure><ol><li>Print &amp; remove supports (GIF 1)</li><li>Insert LED Lamp Kit 001 or WLED Insert (Scroll down for examples of LED Strip) (GIF 2)</li><li>Insert the beacon shell (GIF 3)</li><li>Press fit the rear panel with the rear of the base (use the cable cut out for guidance)</li><li>Press fit sides and top panels</li><li>Join all together with the final front panel</li></ol><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486391/design/2024-06-06_dc9c035fa70668.gif"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486391/design/2024-06-06_a70218cc3ec0a8.gif"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486391/design/2024-06-06_a34b3c23504318.gif"></figure><h3>WLED Examples</h3><figure class="image image_resized" style="width: 50.06%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486391/design/2024-06-06_1b57675eee47e.png"></figure>This is the insert that is printable for the WLED beacon route. It has a 55mm cutout from the top with enough space to fit a microcontroller and any necessary wiring. For my design, I&#39;ve used a 12v LED strip that I have glued spirally 8mm from the bottom to the top. Remember to keep 8mm exposed at the bottom to fit inside the obsidian base. Ive also used an EPS32 controller. There are a bunch of tutorials on <a target="_blank" href="https://www.youtube.com/results?search_query=WLED+setup" rel="nofollow noopener">Youtube</a> on how to use WLED from installation to wiring. If you need further assistance feel free to comment and I will post my setup.<figure class="image image_resized" style="width: 50.74%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486391/design/2024-06-09_256d24d169b35.png"></figure>PLEASE REMEMBER: HEAT WARNINGLED Strip can become hot when on for large durations and the default beacon shell keeps all heat trapped inside the enclosure. Please be cautious in filament selection and consider tougher materials such as PTEG and above. I recommend using the second print plate on the beacon shell print file with the added Minecraft sword air vent to expel heat. &nbsp;<figure class="image image_resized" style="width: 60.09%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486391/design/2024-06-06_59ab15cc9dd8c8.png"></figure>During my testing, I was able to fit 80 LED cells (60 cells/meter) around my insert. The exposed wires (image above) have been cleaned and cut and kept under inside the lamp base (image below). Ive used hot glue to contain the wires and plugs.<figure class="image image_resized" style="width: 60.05%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486391/design/2024-06-06_924f95dc9b1a78.png"></figure><h3>Congratulations &amp; Enjoy!</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486391/design/2024-06-06_5c0b1dab984008.gif"></figure>It&#39;s that easy! Please rate, comment and enjoy your beacon. Happy mining!&nbsp;

Minecraft Beacon Lamp (LED Lamp Kit 001 & WLED)

minecraft

My first self-made sandal. Printed in Men&#39;s size 43 for use with any standard footbed. (But it also works without if necessary.) The pair of sandals costs less than €7.50 (plus electricity) at a TPU price of €25/kg. The filament I use is standard TPU 95A or high speed TPU&nbsp;I have added a conversion table as a picture.If you are unsure about the size, print a version in cheap PLA first and test whether the size fits.  That&#39;s what I did.The straps can be adapted to your own Foot height and glued on accordingly.I use cyanoacrylate superglue that is waterproof and achieves excellent results.  (Cyanoacrylate adhesive is the best for bonding TPU)&nbsp;Here are a few tips:<ul><li>Don&#39;t fasten the straps too tightly. Then they can become uncomfortable. It is best to wear thick socks when attaching them. </li><li>The high speed filament feels harder than the standard TPU. This makes the sandals slippery at first on smooth ground. I took them for a walk outside and afterwards the grip was normal again.</li><li>The Tynmorry Standart TPU feels more comfortable than the Overture HS TPU</li><li>Alternatively, you can use PU artificial leather for the straps. This is softer, but will stretch a little over time.</li><li>The sandals are designed for over 100 kg.  For lighter people, I recommend reducing the infill and lowering the number of upper layers. Perhaps first make a 1 cm thick test print with the selected filament.</li><li>I recommend gluing the strips to the outside first and then attaching them to the inside. Any excess can easily be cut off afterwards.</li></ul>The sandal is still under development. I want to continue to improve the comfort and convenience and ultimately release a good, wearable and affordable shoe.I hope you have fun with the slippers, please write me your experiences and suggestions for improvement.&nbsp;- In the current version, I have reduced the infill to 11% and rounded off the edges of the belts.&nbsp;

3d printed ergonomic sandal

useful

Supergrapher

Update:18th of Jun 2024<ol><li>Just tidying up of the files and a small update for the nozzles. </li><li>The Paint-On numbered covers are kept as a seperate file</li><li>The extra nozzles are now part of the main file.</li></ol>&nbsp;12th of Jun 2024<ol><li>Tweaked the port holes so it grips the PTFE tubes better. (In case you don&#39;t know, you can use PTFE tubes instead of the printed nozzles)</li><li>Very slightly narrow the for hole for the hygrometer so it fits tighter.</li><li>Changed the style of the brackets and the fonts to match that of the Covers</li></ol>11th of Jun 2024<ol><li>Tweaked the internal geometry of the nozzles to reduce rubbing as the filament travels through it. </li><li>If you feel are you getting too much resistance or rubbing from the original Nozzles, you can try wider Nozzles. You can find the Nozzle Pack under print profiles. These nozzles comes in a choice of Original, +0.05 and +0.10. </li></ol>8th of Jun 2024<ol><li>Sliced abit off the side of the cover to make the cover easier to fit when using the top mount. I missed the measurement, it will fit, but just barely. If you are using my Clip-On Top Mount, I&#39;ve updated the file so it works now. </li><li>I&#39;ve brought back the Paint-On numbers for the cover. You can color it yourself (the stencil will appear when you use the Bambu Studio Paint function) or you can just use the one I uploaded under print profiles. <img class="image_resized" style="width: 45.16%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486153/design/2024-06-09_cc8d5d3eff2808.jpg"></li><li>Small adjustments to the clips to make it snap tighter. I&#39;ve also reduced the size of the release lever incase it catches on the spool.</li></ol>&nbsp;&nbsp;Finally I&#39;ve created the ULTIMATE FILAMENT SPOOL ENCLOSURE for the AMS LITE!&nbsp;Thank you for all the support and feedback on the previous design. I’ve incorporated everything I’ve learned to create a new design that I believe is better and more user-friendly. Now, installing and feeding filament is so much easier. The cover is attached using clips, making the process more straightforward. No additional tools or parts are needed, and you have a choice of action panels and action buckets to suit your needs.&nbsp;My favorite action panel is the dual monitoring (inside/outside) hygrometer panel.&nbsp;This is also compatible with my and Bambulab&#39;s AMS lite top mount. You&#39;ll need to remove the screw on the Bambulab version.&nbsp;Installation is also relatively easy. Let’s get started!&nbsp;NOTE PLA for all partsPETG for the clips&nbsp;InstructionsConnect the buckets together as shown using the clips.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486153/design/2024-06-06_c0d1267bb22298.jpg"></figure>Install the plugs by press-fitting them. They don&#39;t need to go in all the way; stop once they are tight. The round-based ones are for the filament to go through, while the square ones are for sealing. &nbsp;I&#39;ve also designed it so that you can use a PTFE tube if preferred. Just gently push it through the hole. I would recommend a very short tube of 2 to 4cm.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486153/design/2024-06-06_d54667eaaf1b5.jpg"></figure>Install the setup onto the AMS Lite. Connect the covers and your choice of action panel together using the clips.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486153/design/2024-06-06_cbde24d2cc6688.jpg"></figure>Work your way around the perimeter of the hygrometer and it should pop into place in the recess. It sits flush when installed correctly. Note that the hygrometer is held in place by it&#39;s brim and not the clips.&nbsp;<a target="_blank" href="https://www.amazon.com/dp/B07GR67G1M" rel="nofollow noopener">https://www.amazon.com/dp/B07GR67G1M</a><a target="_blank" href="https://www.aliexpress.com/item/1005005582069823.html?spm=a2g0o.order_detail.order_detail_item.3.5f81f19cqwKmYb" rel="nofollow noopener">https://www.aliexpress.com/item/1005005582069823.html?spm=a2g0o.order_detail.order_detail_item.3.5f81f19cqwKmYb</a>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486153/design/2024-06-17_60b39b7d93afc.jpg"></figure>Install your choice of Action Buckets.<figure class="image image_resized" style="width: 100%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486153/design/2024-06-06_2a590d0bc9a088.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486153/design/2024-06-06_69b8c7c9fe3ff8.jpg"></figure>Attach the cover using the clips. You may also also install the brackets for additional stability.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000486153/design/2024-06-06_22d56660fab948.jpg"></figure>&nbsp;&nbsp;That&#39;s it, I guess the rest should be quite self explanatory.&nbsp;Have Fun!

Ultimate Filament Spool Enclosure 封箱 for AMS Lite

Daneti

Darth Vader Melted Helmet has supports and prints lovely

Melted Darth Vader Helmet

downl

BuildyBryce

🖱️ A minimal mouse shell compatible with the Bambu Lab Wireless Mouse Components Kit 002. &nbsp;🔨 This mouse is designed to be incredibly easy to edit and remix! &nbsp;📏 Use an included style (angular or rounded), or design your own! <h2>Instructions</h2><figure class="table" style="width: 90.84%"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td>Step 1 - Insert the on/off switch and lens into the base.</td><td><figure class="image image_resized" style="width: 66.39%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000463552/design/2024-05-12_a94e9f65eb6c4.jpg"></figure></td></tr><tr><td>Step 2 - Insert the scrollwheel into the mouse PCB, then insert the PCB into the base.&nbsp;Ensure the on/off switch and lens are positioned correctly.&nbsp;Then, place the battery connectors inside the slots and connect the cable to the PCB.</td><td><figure class="image image_resized" style="width: 66.69%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000463552/design/2024-05-12_496d38336ac7.jpg"></figure></td></tr><tr><td>Step 3 - Insert the battery, then screw the battery cover on using an included screw.&nbsp;Ensure the wires aren&#39;t being pinched.</td><td><figure class="image image_resized" style="width: 66.22%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000463552/design/2024-05-12_1cf3aa0765b4.jpg"></figure></td></tr><tr><td>Step 4 - Place the 2 top pieces onto the base.</td><td><figure class="image image_resized" style="width: 64.39%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000463552/design/2024-05-12_f63420b0a9046.jpg"></figure></td></tr><tr><td>Step 5 - Attach the top pieces to the base using 4 included screws. The screws should be flush with the bottom of the base.&nbsp;Then, attach the adhesive feet.&nbsp;You&#39;re done! ⭐</td><td><figure class="image image_resized" style="width: 64.16%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000463552/design/2024-05-12_9f894bdda1b57.jpg"></figure></td></tr></tbody></table></figure><h2>Design your own!</h2>Files are available to download as editable .3mf files so that you&#39;re able to quickly edit it without the need to start designing from scratch.&nbsp;There&#39;s a few ways to remix:<ul><li>The easiest way is to customise one of my included top pieces.</li><li>Or, you can design your own top piece that&#39;s compatible with my base piece. </li><li>Alternatively, remix my base piece to design your own super custom mouse. This will save you having to design the cut-outs for the PCB, battery, lens, etc.</li></ul><h2>Parts to 3D Print</h2><figure class="table" style="width: 90.73%"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td>Base piece&nbsp;Includes base + battery cover.&nbsp;The battery cover is highly recommended as it also locks the PCB into place.</td><td><figure class="image image_resized" style="width: 96.78%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000463552/design/2024-05-12_35527036cd35b.png"></figure></td></tr><tr><td>Top piece&nbsp;2 styles<ul><li>Rounded, or</li><li>Angular (Easier to 3D print)</li></ul>Or, design your own!</td><td><figure class="image image_resized" style="width: 82.02%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000463552/design/2024-05-12_844cb0669e3e3.png"></figure><figure class="image image_resized" style="width: 80.2%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000463552/design/2024-05-12_55625b6d404b7.png"></figure></td></tr></tbody></table></figure><h2> </h2><h2>Happy printing &amp; remixing! 😃</h2>

Minimal Mouse 002 (Remix Me!)

myszki

IdeenDüse

Ich habe das neue PETG Transluzent Filament von BambuLab ausgetestet. Dafür habe ich eine Kristalllampe designed, da ich finde, dass Kristalle gut mit dem Filament zur Geltung kommen und es authentisch aussieht. Ich habe alle Teile auf meinem BambuLab X1C gedruckt und die Textured PEI plate von BambuLab verwendet.&nbsp;Hier ist der Amazon Affiliate Link zum passenden LED-Stripe: <a target="_blank" href="https://amzn.to/42Lkp0D" rel="nofollow noopener">https://amzn.to/42Lkp0D</a>&nbsp;NEU!!!!Wenn man sich eine Kristallampe baut, hat man noch LED-Streifen übrig, aber kein Steuergerät und Fernbedienung mehr, um sich weitere bauen zu können.Ich habe beim Verkäufer angefragt, ob man Steuergerät und Fernbedienung ohne LED-Streifen bestellen kann, leider war dies nicht möglich.Also habe ich nach einer Kompatiblen Lösung gesucht und etwas passendes gefunden. Ein einfache Möglichkeit den Restlichen LED-Steifen zu Lampen zu verarbeiten. Die Anleitung stelle ich hier als PDF zur Verfügung. &nbsp;Um meine Arbeit kostenfrei zu Unterstützen, würde ich mich freuen wenn ihr die Affiliate Links zum Kauf der benötigten Bauteile verwendet:&nbsp;Passendes Steuergerät mit Fernbedienung:     <a target="_blank" href="https://amzn.to/49AyTDd" rel="nofollow noopener">https://amzn.to/49AyTDd</a>Netzteil:                                                                   <a target="_blank" href="https://amzn.to/49SAowk" rel="nofollow noopener">https://amzn.to/49SAowk</a>&nbsp;Hier geht es zum Bauanleitungs Video:&nbsp;<figure class="media"></figure>&nbsp;I tested the new translucent filament from BambuLab.I designed a crystal lamp for this because I think that crystals show off well with the filament and it looks authentic.I printed all the parts on my BambuLab X1C and used BambuLab&#39;s Textured PEI plate.you need no Support.&nbsp;Here is the Amazon affiliate link to the matching LED strip   : <a target="_blank" href="https://amzn.to/42Lkp0D" rel="nofollow noopener">https://amzn.to/42Lkp0D</a>&nbsp;NEW!!!! If you build a crystal lamp, you still have LED strips left, but no control unit or remote control to be able to build more. I asked the seller whether it was possible to order the control unit and remote control without LED strips, unfortunately this was not possible. So I looked for a compatible solution and found something suitable. A simple way to process the remaining LED strips into lamps. I provide the instructions here as a PDF.&nbsp;In order to support my work free of charge, I would be happy if you use the affiliate links to purchase the components you need:&nbsp;Suitable control device with remote control:       <a target="_blank" href="https://amzn.to/49AyTDd" rel="nofollow noopener">https://amzn.to/49AyTDd</a>Power supply:                                                             <a target="_blank" href="https://amzn.to/49SAowk" rel="nofollow noopener">https://amzn.to/49SAowk</a>&nbsp;&nbsp;  &nbsp;&nbsp;&nbsp;

Kristalllampe /Crystal lamp

led lamp kit

FallenAngel

Pill Organizer based on medieval ageI would recommenced printing in black and dry brushing with gold to make it looks like antique.You need following items after 3D printing to make it functional.<ul><li>Magnets - 3 x 3 mm ( 4 quantities) </li><li>Screw - M2 x 35 mm (1 quantities with bolt) </li></ul>

Vampire Vitamins - Organizer

props

Ruvim KUB

<h2>Organizer for small things (25mm Height)</h2>I do a lot of printing of small devices and for them I have a lot of small nuts, bolts and different modules.My practice has shown that it is more convenient and compact when the container is placed on the container.I hope you will find this organizer useful.&nbsp;<a target="_blank" href="https://makerworld.com/en/models/115716#profileId-124378" rel="nofollow noopener">There are also organizers with a height of 16mm</a><a target="_blank" href="https://makerworld.com/en/models/149624#profileId-163286" rel="nofollow noopener">There are also organizers with a height of 25mm</a><a target="_blank" href="https://makerworld.com/en/models/202754#profileId-223110" rel="nofollow noopener">There are also organizers with a height of 40mm</a>&nbsp;&nbsp;And also I would like to tell you that I recently started a small store on <a target="_blank" href="https://www.etsy.com/shop/3dkub" rel="nofollow noopener">Etsy.com</a> here will appear instrementy and exclusive projects that will not be in the open access.&nbsp;<h2>My some other things:</h2><figure class="image"><a href="https://3d.ruvim.info/thingiverse" target="_blank" rel="nofollow noopener"><img src="https://3d.ruvim.info/thing.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/151492#profileId-165387" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/580499/2024-01-21_140ed1f4e28fc.jpg"></a><a target="_blank" href="https://makerworld.com/en/models/149624#profileId-163286" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/580499/2024-01-21_c9f371a901922.jpg"></a><a target="_blank" href="https://makerworld.com/en/models/135080#profileId-146564" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/580499/2024-01-11_f09984058f1de.jpg"></a><img src="https://3d.ruvim.info/0450.png"><a target="_blank" href="https://www.thingiverse.com/thing:4968267" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Auto-Solder-Feeder-V1.1.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4934874" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Magnetic-mount-for-Street-style-Clocks.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/133763#profileId-145135" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Rectangular-stand-for-cotton-buds-and-disks.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4872540" rel="nofollow noopener"><img src="http://things.ruvim.info/img/phone-clip.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4860781" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Anex-sport-Min.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/97564#profileId-104137" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Stand-for-toothpaste-V2.0.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/105242#profileId-112325" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Stand-for-cotton-swabsticks-and-discs-V5.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4751509" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Smart-faucet-on-Arduino-(filter-resource-counter).jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/133785#profileId-145164" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Organizer-for-3D-printer.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4709801" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Acetone-Bath-on-Magnets.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4689514" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Case-for-rfid-tags.jpg"></a> <a href="Nozzle-Box.jpg" rel="nofollow"><img src="http://things.ruvim.info/img/Nozzle-Box.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/127746#profileId-138242" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Table-Adjustment-Knob-M3.jpg" alt="Table Adjustment Knob M3"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4539243" rel="nofollow noopener"><img src="http://things.ruvim.info/img/PCB-Etching-Tray.jpg" alt="PCB Etching Tray"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4495533" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Speed-Controller-220V.jpg" alt="Speed Controller 220V"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4458304" rel="nofollow noopener"><img src="http://things.ruvim.info/img/M%D0%BEdular-Mini-Circular.jpg" alt="Mоdular Mini Circular"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4383145" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Clock,-Counter-Subscribers..jpg" alt="Clock, Counter Subscribers."></a> <a target="_blank" href="https://www.thingiverse.com/thing:4361811" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Compass---Plotter.jpg" alt="Compass - Plotter"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4356203" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Phone-Clip..jpg" alt="Phone Clip."></a> <a target="_blank" href="https://www.thingiverse.com/thing:4327360" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Phone-Stand.jpg" alt="Phone Stand"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4317738" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Mini-Grinder.jpg" alt="Mini Grinder"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4304240" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Disc-Sander-Duo.-D50mm,-D75mm.jpg" alt="Disc Sander Duo. D50mm, D75mm"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4265679" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Lifting-Gear-For-Automatic-Nozzle-Cleaner.jpg" alt="Lifting Gear For Automatic Nozzle Cleaner"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4216312" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Mini-electric-lighter.jpg" alt="Mini electric lighter"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4212059" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Stand-for-toothpaste.jpg" alt="Stand for toothpaste"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4123230" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Camera-Weight-for-Diving.jpg" alt="Camera Weight for Diving"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4099456" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Electric-lighter.jpg" alt="Electric lighter"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4086763" rel="nofollow noopener"><img src="http://things.ruvim.info/img/The-best-soldering-iron-stand.jpg" alt="The best soldering iron stand"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4056390" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Flux-stand.jpg" alt="Flux stand"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4084435" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Mobile-Hard-Drive:-2.5-Inch-USB-3.0-SATA.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/118219#profileId-127104" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Magnetic-plate-for-little-things.jpg" alt="Magnetic plate for little things"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3970160" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Clamp-for-firmware-controllers-6-pins.jpg" alt="Clamp for firmware controllers 6 pins"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3976187" rel="nofollow noopener"><img src="http://things.ruvim.info/img/2-relays-box-or-ESP-01-with-relay.jpg" alt="2 relays box or ESP-01 with relay"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3970750" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Case-for-Ndemcu.jpg" alt="Case for Ndemcu"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3942946" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-A-B-C-D-E.jpg" alt="Alphabet for children. A B C D E"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3946878" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-F-G-H-I-J.jpg" alt="Alphabet for children. F G H I J"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3974764" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-K-L-M-N-O.jpg" alt="Alphabet for children. K L M N O"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3989549" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-P-Q-R-S-T.jpg" alt="Alphabet for children. P Q R S T"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3991721" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-U-V-W-X-Y-Z.jpg" alt="Alphabet for children. U V W X Y Z "></a> <a target="_blank" href="https://www.thingiverse.com/thing:3912631" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Replacement-SD-Card-Case.jpg" alt="Replacement SD Card Case"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3914719" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Solder-feeder.jpg" alt="Solder feeder"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3851649" rel="nofollow noopener"><img src="http://things.ruvim.info/img/USBasb-case.jpg" alt="USBasb case"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3845727" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Magnet-stick.jpg" alt="Magnet stick"></a>&nbsp;&nbsp;

Organizer for small things (40mm Height)

mama

MadMax3D

100mm earth lithophane mounted on a lighted base. The lithophane is printed in white and then painted with water colors. I&#39;m no artist. I used a cheap kid&#39;s set of water colors and just tinted the painted areas. You don&#39;t need much color to make it pop. The lighted base is included in a separate profile. Update 2024-05-07: My sincere apologies. A user discovered an error in the earth profile. I had inadvertently turned on “detect thin walls” which causes holes and marred areas in the globe.  If you have already printed it, please re-download the current profile or turn off “detect thin walls” in the slicer. Sorry for the inconvenience.&nbsp;<a target="_blank" href="https://makerworld.com/en/@MadMax3D/collections/1204492" rel="nofollow noopener">Check out my other spherical lithophanes</a>&nbsp;Purchased PartsI used <a target="_blank" href="https://www.amazon.com/gp/product/B0BBPHF58T/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;th=1" rel="nofollow noopener">these</a> USB Light SticksAny <a target="_blank" href="https://www.amazon.com/dp/B08FM5JHH1/?coliid=IZ55K9HKA3GJ8&amp;colid=2P141A3WT8ECQ&amp;ref_=list_c_wl_lv_ov_lig_dp_it&amp;th=1" rel="nofollow noopener">USB extender</a> cables will work.<a target="_blank" href="https://www.amazon.com/dp/B08C7XF63J?ref=ppx_yo2ov_dt_b_product_details&amp;th=1" rel="nofollow noopener">Water color paint set</a>&nbsp;Printing InstructionsMy profile has all my preferred settings. If you prefer to plate your own (stl&#39;s in the raw files section), I suggest the following settings:<ul><li>If using my print profile, make sure to select your printer type, plate type and filament profile from the drop down menus in the slicer.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000454410/design/2024-04-27_8bad4f8ca501b.png"></figure><ul><li>I printed the lithophanes at .2mm layer height with two height range modifiers (10-15mm and 98-120mm) set at .1mm layer height. This reduces the gaps in the flattest parts of the sphere.</li></ul><figure class="image image_resized" style="width:34.45%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000454410/design/2024-04-27_0a6d030ad144.png"></figure><ul><li>You could set the layer height for the whole sphere lower (like .1mm), but it will take longer to print.</li><li>4 walls, 100% rectlinear infill, arachne wall generator. (arachne takes longer to slice, but generates a better print in my opinion)</li><li>I slowed down the outer wall speed to 50mm/s</li><li>The light base should be set to .2mm layer height and 15% infill of choice.</li></ul>Make Your Own Lithophanes Using My Light BaseYou can generate your own lithophanes using your own photos at <a target="_blank" href="https://lithophanemaker.com/Lithophane%20Sphere.html#processing" rel="nofollow noopener">Lithophanemaker.com</a>. The lithophane can be set for any diameter as long as the base is the correct size to fit in the lighted base. Your photograph should be approximately 3.3:1 width to height ratio to wrap all the way around the sphere.<figure class="image image_resized" style="width:51.63%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000454410/design/2024-05-05_63446faefbb8.jpg"></figure>&nbsp;I used the following settings:Lithophane Resolution: 0.25 Sphere Diameter: 100 Picture Angular Height: 130 Picture Angular Width: 360.00 Maximum Thickness: 2.7 Minimum Thickness: .8 Cylinder Outer Diameter: 40 Cylinder Height: 10 Cylinder Thickness: 5 Cylinder Ledge Outer Diameter: 50 (make sure this is set to 50mm to fit into the light base) Top Hole Outer Diameter: 0  &nbsp;

Earth Lithophane 100mm

lithopane

fay3dlab

Last week i was browsing around and i saw this star wars desk lamp.. it was a tie fighter desk lamp.. looks cool with the light coming from the cockpit.. the only thing that supprise me was the price.. USD100 on ebay..So i decided to make my own.. since i already had the tie-interceptor from my <a target="_blank" href="https://makerworld.com/en/models/407234#profileId-309304" rel="nofollow noopener">star wars book nook</a>.. i just need to convert it into a tie-fighter lamp.. I was going to use my mic stand arm as the body and im going to make a heavy semi sphere deathstar dome as the base.. and im going to LED lights as the light source that is being shine through the cockpit window.. Im using the bambulab LED kit 001 for the light..&nbsp;<blockquote>If you&#39;re thinking of buying the LED kit.. please do support me by using my affliate link here.. <a target="_blank" href="https://shrsl.com/4g18i" rel="nofollow noopener">LED LAMP KIT 001</a> every little things helps me out..</blockquote>&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/858696/2024-04-15_d14051328b621.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/858696/2024-04-15_4eb3e76381cde.jpg">The whole project is 3d modelled using tinkercad.. You can find the assembly instructions on <a target="_blank" href="https://www.instructables.com/Tie-fighter-Desk-Lamp/" rel="nofollow noopener">my instructable page</a>.. Unlike my other 3d printed project.. i manually colored the desk lamp using colored spray can and some marker pens.. i think it looks better painting it manually than just multicolor print it.. I&#39;m going to make a collection of the star wars desk lamp and i want you guys to vote on which star wars ship should i do next.. vote here<a target="_blank" href="https://www.buymeacoffee.com/fay3dlab/which-star-wars-fighter-ship-make-desk-lamp-next" rel="nofollow noopener"><div> https://www.buymeacoffee.com/fay3dlab/which-star-wars-fighter-ship-make-desk-lamp-next</div></a>  I hope you&#39;ll have fun 3d printing the tie fighter desk lamp&nbsp;<figure class="table" style="height:162.344px;width:960px;"><table style="background-color:rgb(255, 255, 255);border:1px double rgb(179, 179, 179);"><tbody><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;">If you would like to support me, you can join me on my <a target="_blank" href="https://www.buymeacoffee.com/fay3dlab" rel="nofollow noopener">buymeacoffee</a> page..</td></tr><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;">By joining me as a supporter.. you&#39;ll be able to get behind the scenes informationon my current projects as well as future projects..</td></tr><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;">And if you&#39;re looking to sell my prints.. you can join my merchant membership tier as lowas USD10 a month..</td></tr></tbody></table></figure>

Tie Fighter Desk Lamp LED kit 001

lampy

PAPA Emeritus IV

Full Bed Printers The Model is 167.86x235mm in sizeA1 mini The Model is 121.43x170mm in size&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm&nbsp;Filaments Used: PLA BambuLab Basic Black Transmission Distance: 0.6 PLA BambuLab Basic Blue Gray Transmission Distance: 3 PLA BambuLab Basic Jade White Transmission Distance: 5 PLA BambuLab Matte Scarlet Red Transmission Distance: 2 This print uses 4 unique filamentsSwap Instructions: Start with Black At layer #7 (0.64mm) swap to Blue Gray At layer #9 (0.8mm) swap to Jade White At layer #17 (1.44mm) swap to Scarlet Red At layer #24 (2mm) swap to Jade White for the rest.

Samurai Soul

bueforge

Bamingo Design

<ul><li>🌊🌀 Dive into the mesmerizing world of waves with our Wave Coasters, designed with a realistic image view that captures the beauty and movement of the ocean.</li></ul>Wave Coaster: Capturing the Ocean<ul><li>🎨 Vivid View: Our Wave Coasters feature a detailed and intricate design of waves, reminiscent of the famous Japanese woodblock print “The Great Wave off Kanagawa”. The wave patterns on each coaster are dynamic and full of movement, giving a visual impression of rolling waves.</li><li>👶 Easy to Print: No need for (AMS) or (MMU). Only two manual filament swaps are needed to complete the model.</li></ul>Technical Specifications:<ul><li>📏 Size:<ul><li>10 cm</li></ul></li><li>🔧 Print Settings:<ul><li>Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm</li></ul></li><li>🌈 Color Changes:<ul><li>Start with Blue</li><li>At layer #12 (1.04 mm), change to Light Blue</li><li>At layer #18 (1.52 mm), change to White for the rest.</li></ul></li><li>📋 Assembly and Usage Tips:<ul><li>Alternatively, use our ready-to-print 3MF file—it automates these steps.</li><li>The files are available in STL, Prusa 3MF, and Bambu Lab 3MF file formats.</li></ul></li></ul>Explore More Designs:<ul><li>Dive deeper into our collection of nature-inspired coasters for more designs that capture the beauty of the natural world:<ul><li>🗼 <a target="_blank" href="https://makerworld.com/en/models/251129#profileId-267476" rel="nofollow noopener">City Coasters</a></li><li>⛰️ <a target="_blank" href="https://makerworld.com/en/models/30652#profileId-27193" rel="nofollow noopener">Mountain Coasters</a></li><li>❄️ <a target="_blank" href="https://makerworld.com/en/models/84832#profileId-90731" rel="nofollow noopener">Snowflake Coasters</a></li></ul></li></ul>Licensing Information:<ul><li>These designs are for personal use only. To access them for commercial purposes and enjoy exclusive benefits, consider joining our Memberships. <a target="_blank" href="https://www.printables.com/@BamingoDesign#join:397" rel="nofollow noopener">Printables Memberships</a></li></ul>Stay Connected:<ul><li>Be the first to know about our newest designs by following us on Twitter and Instagram. Find all our social media links and more at <a target="_blank" href="http://bamingodesign.com/" rel="nofollow noopener">bamingodesign.com</a>.</li><li>We&#39;re excited to see your creations! Tag us when sharing photos of your prints and connect with us. Your feedback and requests are always welcome. 💙</li></ul>

Wave Coasters - Hueforge

coaster

AngryPearl

Nail box organizer for 20 oval bottles and 4 squareFits with every bottle on market&nbsp;Profile with low filament usage&nbsp;Checkout my profile for similar models: <a target="_blank" href="https://makerworld.com/en/u/2375310028" rel="nofollow noopener">https://makerworld.com/en/u/2375310028</a>

Nail box organizer Oval and Square NeoNail

anka

VektorKnight

A re-design of my previous <a target="_blank" href="https://makerworld.com/en/models/63205" rel="nofollow noopener">magnetic box</a> which seeks to address some of the shortcomings of the original. The lip has been inverted so that there is no shelf inside the box where items can get caught. Larger magnets (8mm) have been used this time for more reliable lid retention as well as better tolerances and cutouts to help prevent any glue spilling out. There&#39;s also an optional insert which allows the box to be printed out of any material while protecting the interior. Notches matching the feet have been added to the lid to allow the boxes to stack and stay in-place.&nbsp;Organizational inserts are an idea I had but I couldn&#39;t figure out a set of common layouts that I was happy with. So only the basic protective insert is included for now.<h3>Printing</h3>Examples were printed in Bambu PETG-CF for the base/lid and Bambu PETG Basic for the inserts. However, it&#39;s well-known that these filaments can be difficult to print reliable without a lot of tuning. The recommended materials are PLA/ABS/ASA for the base/lid and PETG/ABS/ASA for the insert. PLA-CF may be a good alternative to retain the aesthetic of the examples without the hassle of PETG-CF.&nbsp;For extra quality, printing outer walls first should work fine. The box has been designed with 45-degree chamfers and no significant overhangs or bridges for ease of printing. The cutouts for the feet and stacking should bridge just fine without supports.&nbsp;For additional strength, three walls may be used though two should be enough for most cases. I prefer honeycomb infill at 20% but this is personal preference.&nbsp;If you decide to print using a filament with a lot of shrink/warping (ABS/ASA/PC), ensure you have the correct compensation values or the tolerances may be off. The magnets should slide in without resistance.&nbsp;*Unfortunately, the 175x175mm variant will not fit on an A1 Mini due to the extra material for the walls.<h3>Assembly</h3>The provided profiles and raw STL files expect 8x3mm magnets and 6x2mm rubber feet. These <a target="_blank" href="https://www.amazon.com/gp/product/B097HCT436/?th=1" rel="nofollow noopener">magnets</a> and <a target="_blank" href="https://www.amazon.com/dp/B08GLJB3Z4" rel="nofollow noopener">rubber feet</a> work really well. I have seen a lot of variance in the strength of magnets off Amazon. The ones I linked worked well but any should cut it as long as they are decent neodymiums.&nbsp;While the previous box was press-fit, I found this to be extremely unreliable. Especially with different printer tolerances and creep issues. The magnets must be glued in this time. I have added plenty of tolerance that should cover most printers these days. Notches have been added to try and catch any glue that seeps out.&nbsp;The magnetic feet in the provided BOM are adhesive and should stick on within the provided cutouts on the bottom.&nbsp;The insert has enough tolerance to slide in to the box. Due to layer lines and seams, it may need some help.&nbsp;<a target="_blank" href="https://www.amazon.com/gp/product/B097HCT436/?th=1" rel="nofollow noopener">8x3mm Neodymium Magnets</a><a target="_blank" href="https://www.amazon.com/dp/B08GLJB3Z4" rel="nofollow noopener">6x2mm Rubber Feet</a><h3>Customization</h3>I have included the source CAD file for Fusion 360 for any customization, remixes, etc. Parameters are set up for just about every aspect of the box other than some features which were better off being kept fixed to avoid broken variants. I do not recommend going below a wall-thickness of 3.2mm as this aligns well with 0.4 and 0.6mm nozzles while providing good strength.

Stackable Magnetic Box

parametric

wuguigui

This is a 3D printable swatter based on my friend Yu Yang&#39;s design. To thank his contribution to this design, all points I got from this model will be given to him after published for 1 year.&nbsp;I also made efforts to make it durable and sturdy, you need to cut a piece of filament (D1.75mm), heat and weld the 2 sides to fix the parts, as in the image shown below.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000445108/design/2024-04-27_397a695669059.png"></figure>Disclaimer: This model is part of the Creator Program, When you purchase the hardware kit through the links below, creators may earn an affiliate commission as a reward of their work. (The creator program is currently in the trial phase. The application is not yet open to public.)&nbsp;Recommended filaments: <a target="_blank" href="https://shrsl.com/4i9u7" rel="nofollow noopener">Bambulabs PETG-CF </a>and <a target="_blank" href="https://shareasale.com/r.cfm?b=2282157&amp;u=4048186&amp;m=138211&amp;urllink=store%2Ebambulab%2Ecom%2Fproducts%2Fpla%2Dtough&amp;afftrack=" rel="nofollow noopener">Bambulabs PLA Tough </a>, because of the need for toughness. It&#39;s a little trick to print the face parts, so please try the print profiles I uploaded as I have tried successfully several times.&nbsp;Watch the video to get more information:<figure class="media"></figure>If you were in China, Please watch this Video:<figure class="media"><oembed url="https://www.bilibili.com/video/BV1ZJ4m1J7P8/?share_source=copy_web&amp;vd_source=ee6ec7eee552df5e9a9849094bf18b9e"></oembed></figure>&nbsp;If you like it, please feel free to boost me, thank you.

Swatter

junky junk

lampshade LED lamp kit 369

doniczki

MrRemixSTL

Este es un test de tolerancias muy sencillo para que puedas poner a prueba tu impresora 3D. Con este test podrás ver la tolerancia nativa de tu impresora 3D.  Importante: Para hacerlo, la expansión horizontal o la compensación XY tiene que estar ajustada en cero. Además, si el logo de Control3D no sale, puede ser indicativo de tener las retracciones altasModelo 100% CTRL 3D

TEST DE TOLERANCIAS Control 3D

testy

Alxthunder

This is a storage container. I printed them using Wood Filament from Teq Stone. The color is wood popular. The spiral pattern of the storage container flows beautifully into the pattern of the lid. You can scale the size in Bambu Studio. Check out my other spiral products for the bathroom. Maybe there is something there for you. Have fun reprinting!&nbsp;<a target="_blank" href="https://makerworld.com/en/models/232002#profileId-249229" rel="nofollow noopener">https://makerworld.com/en/models/232002#profileId-249229</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000422677/design/2024-04-14_0abdf68803e77.jpg"></figure>

Spiral storage box with lid

lazienka

RestoreDoctor

Small cap should be printed in TPU and scale up to 99%Settings:<ul><li>0.16mm Standard +custom settings:</li><li>Wall loops min. 3</li><li>Infill 100 %</li></ul>

PET bottle - watering cap

Cinderwing3D

Hello everyone!  Today I want to present to you the first ever completely free Cinderwing3D Dragon - The Bamboo Dragon! Bambulab reached out to me asking if I wanted to make a dragon for them and seeing how I use their printers for prototyping.... it was an easy yes!As with all my designs this model is an easy print-in-place and requires no supports. All you need is a clean bed and you&#39;re off! I also have included two 3MF files for multicolor, as shown in the pictures!  Print Settings: .2 Layer height, 15% infill, gyroid infill, no brim, and no supports. Please feel free to join our <a href="discord.gg/cinderwing3d" rel="nofollow">Discord</a> chat for help and discussions. Filaments used were Bambu Green PLA Basic, Bambu Red PLA Basic, and Gold Bambu Silk PLA! <a target="_blank" href="https://shareasale.com/r.cfm?b=2354730&amp;u=3729583&amp;m=138211&amp;urllink=&amp;afftrack=" rel="nofollow noopener">Feel free to use my affiliate link to grab some for yourself!</a> The Green Gradient filament <a target="_blank" href="https://amzn.to/3Htn19A" rel="nofollow noopener">can be found here!</a> The Green and Brown Gradient <a target="_blank" href="https://amzn.to/47N8EYF" rel="nofollow noopener">can be found here!</a> And the Tricolor<a target="_blank" href="https://amzn.to/3UfR3W3" rel="nofollow noopener"> is here!</a> ----- Hi, I&#39;m Tracy! Veteran, full-time mom, and entrepreneur at heart! I love creating unique and fun designs!This design (like all Cinderwing3D designs) is under copyright. Which means, upon purchase, you do NOT have the right to sell commercially. If you would like to legally sell them commercially, please join my Tribe or my Patreon and subscribe to the tier for commercial resale.  The Digital files are never to be re-sold, shared, or given away!<h4>Commercial License and monthly bonus models: <a target="_blank" href="https://than.gs/u/1780858?plans=true&amp;affiliateCode=jazzyplz" rel="nofollow noopener">Thangs Memberships</a> <a target="_blank" href="https://www.myminifactory.com/users/Cinderwing3D?show=tribe" rel="nofollow noopener">Tribes</a> <a target="_blank" href="https://www.patreon.com/cinderwing3d" rel="nofollow noopener">Patreon</a></h4><h4>Please see our other public models here: Check us out on our socials! <a target="_blank" href="https://www.facebook.com/cinderwing3d" rel="nofollow noopener">Facebook</a> | <a target="_blank" href="https://twitter.com/cinderwing" rel="nofollow noopener">Twitter</a> | <a target="_blank" href="https://www.instagram.com/cinderwing3d/" rel="nofollow noopener">Instagram</a> |<a target="_blank" href="https://tiktok.com/@cinderwing3d" rel="nofollow noopener"> Tiktok</a></h4>

Bamboo Dragon Cinderwing3D X BambuLab

dragons

Industriee

Simple Dust cover magneticMagnet: 2x6 mmPause in print profile

Magnetic Dust cover P1P - P1S - X1C

junk

chiz_m

If you like to show appreciation for the effort that went into creating this model, pls hit that BOOST button!&nbsp;A <a target="_blank" href="https://makerworld.com/en/models/18035#profileId-16764" rel="nofollow noopener">base/diorama builder</a> is now available for download for this mini figure model!<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000018045/design/4fb50df1-8c36-4d0c-88ec-bcc8e5122b9c.jpg"></figure>___________<h3>IMPORTANT NOTE ON COMMERCIAL USE OF MY MODELS</h3>Please note that I am sharing my designs to any one to enjoy but for personal use only. I have NOT provided any commercial license to any one allowing the sale of 3d printed copies of my designs. Seeing my designs being sold for profit is discouraging for me to continue coming up with more designs. I will not hesitate to report to Etsy and other online sites if I find them being sold.__________This is a kit card of Minecraft Turtle in mini figure scale. Parts can easily be removed from the sprue without using cutters/clippers just by twisting the part.Default scale is comparable to the Minecraft mini figures but of course you can scale it up to as large as you want! :)<h4>Usage Options</h4><ol><li>Assemble as is and use as toy/collectible; or</li><li>Use the alternative part with loop and glue the halves together to make for a great keychain ornament!</li></ol><h4>Printing Reminders</h4><ul><li>Print as oriented, with NO supports needed.</li><li>If you&#39;re printing in multiple colors, please note that due to several color swaps, it would take longer to print.</li></ul><h4>Difficulty Level (Easy, Medium, Hard)</h4><ul><li>Printing: Medium - Bed should be leveled well to ensure small parts stick well to the build plate. Requires printing slower during the first few layers. May require lots of filament swaps if printed in multi-color.</li><li>Assembly: Easy - Parts should fit really easy. The flippers are intentionally designed to be loose and wiggly. See pictures for correct orientation of the flippers.</li></ul>

Minecraft-inspired Turtle Mini Figure Kit/Keychain

hania

K-Studio.ca

A tool to hold microfiber towel to clean build plates with ease.<ul><li>Print in PLA</li></ul><h4>Filament used in photo:</h4><ul><li>Bambu PLA Metal</li><li>Bambu PLA Matte</li></ul><h4>Updates </h4>March 23, 2024<ul><li>Added an alternative knob for thin cloth or sandpaper.</li><li>Original is designed to bottom out to prevent vertical force to break the print apart.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/754191/2024-03-23_13ab91d9f5c498.jpg"></figure><h4>Instruction</h4><ol><li>Simply take the two blocks align to the microfiber and cut to the same rectangle size.</li><li>Wrap the microfiber around the edge and crimp it down.</li></ol><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/754191/2024-03-23_6dbc3edb91bb7.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/754191/2024-03-21_757e6c3f7297d8.gif"></figure>

Build Plate Cleaner

my printer

pigworlds

The cover page of the book “3D Printed Science Projects” showcases an exquisite camellia flower model. Notably, the petals of this model exhibit an impressive 70-degree overhang.&nbsp;Kudos to the authors of the book.

Camellia flower

junk2

Zurlingo-3D

<h2>Modular Slidey Storage Pod</h2>&nbsp;<figure class="image image_resized" style="width:60.93%;"><img src="https://makerworld.bblmw.com/makerworld/draft/491186/2024-01-31_1c4c74b291f9f.gif"></figure>&nbsp;Features:<ul><li>3 Shelves For Storage</li><li>1 Full Pod Prints In Under 9 Hours</li><li>Easy Assembly</li><li>Sliding Door</li><li>Stylish Design</li><li>Great For Use As A First Aid/Medicine Cabinet</li><li>Can Be Colour Coded For Different Purposes</li><li>Perfect For 3D Printer Parts, Adaptors, Cables, SD Cards, USB Sticks, Scrapers And Anything Else That Will Fit!</li><li>Easy Removal From The Wall For Simple Loading, Unloading And Organizing</li><li>Modular System That Can Be Mounted In Horizontal And Vertical Rows (Single And Double Mounts Included)</li><li>Strong And Reliable Storage Solution</li><li>Can Be Printed On An A1 Mini</li><li>3 Different Labelled Doors Included - ‘Parts’, ‘Tools’, ‘First Aid’</li></ul>&nbsp;Assembly:<ul><li>Glue the ‘Shelves’, ‘Side Left’ and ‘Side Right’ together.</li><li>You only need to add glue to the very edge of the shelves and then seat them in the slots in each side piece.</li><li>Once the glue is dry, insert the door through the grooves that are cut in the door channel</li><li>Ensure the door is in the correct orientation as it slides in from back to front</li><li>Slide the door all the way round its channel until it meets the stop at the front</li><li>Insert the 2 small stop pieces to close off the door channel. This is optional as once mounted on the wall, the door handle acts as a stop.</li></ul>Assembly should take no more than 5 minutes.&nbsp;During assembly you must ensure all edges of the shelves are seated into their corresponding slots. If they are not all the way in then the sliding door will not function correctly.&nbsp;Add some lubricant to the slots that the door slides in, for a smooth motion. I use silicone grease and it works great.&nbsp;Tip: You can make the pod any width you like! - You just need to scale the shelves and the door up or down in Bambu studio.<ul><li>To do this, scale both parts in the X-axis only and ensure the door is always 2.9mm narrower than the shelves.</li></ul>&nbsp;This design is the first version I have made of this concept - If you have any issues or recommendations for edits or additions, please leave a comment or message me! I'm open to constructive feedback to make this as good as it can be :) - It would also be good to add some additional features that users may want to see in the future. I already have some ideas, but would love to hear what you think too!&nbsp;Thanks for looking!&nbsp;Please share your makes with this one! - I had a fun time designing this and am very happy with how it turned out.&nbsp;Also, please rate and review your printing experience :) - It helps my designs get seen by more people :P