cosmicoutkast

Roqui

Print in place!Can be printed on all printers &amp; 60% infill recommended (PLA)

"ON" Ashtray

janelle

darren.meier

Hi! Please take a moment to read the ‘important updates’ section before you print anything, to ensure you get exactly what you need from the model. Thanks!&nbsp;I&#39;ve printed a couple of neat plate holders from MakerWorld but none quite met my needs-- mostly because they don&#39;t fit the plate without a ton of wiggle room. With that single issue in mind, I… well to be honest I went kinda overboard. This thing is sorta overengineered because I have no filter. Snug-but-not-tight plate storage for X, P, and A (and mini!) series printers, your way. With files included for four, six, and eight slot versions you build what you want. With the plate rails modeled as stopped dovetails, print them separately in whatever colors you want and slide them securely into a base that&#39;s whatever color and material you want. Then print the front Bambu badge pieces in colors of your choosing and attach them with a dot of hot glue or CA glue. Want to be a goth? Dope. Pastels? Neat. Want to make the whole thing in the colorway of your favorite sports team? Go on girl, do your thing. Make something awesome, show it off. Thanks for checking it out and have a great day!&nbsp;IMPORTANT UPDATES!&nbsp;Thanks to a shoutout from @Skorpeyon, I was made aware that the default rails are too tight a fit for plates that have stickers on both sides (they fit perfectly for other plates, including Juupine and the high temp and standard PEI plates). Should you find any of your rails are slightly tight for a certain plate to fit, I&#39;ve included an additional model file for a rail with a gap that is 60% wider. I apologise for any inconvenience caused, none of the plates I had on hand while designing were of a problematic thickness. I appreciate your understanding! &nbsp;EDIT! I&#39;ve also included an additional-additional model for an even wider rail, per a request I received to create an option to support 2mm plates like the Lightyear G10 garolite. If you have any 2mm-ish plates you need to store, please print this model for those slots. Thank you!&nbsp;I also slightly adjusted the model in the following way-- the bevel on the bottom front surface has been made slightly less aggressive to avoid any print issues when printing the front surface face down on the plate, per feedback. Thank you!&nbsp;ASSEMBLY NOTES!&nbsp;Not a lot to this one. Provided your printer is maintained and calibrated, things should go smoothly. If you&#39;re going to move the models around on different plates to print in a load of colors, or if you just want to reorganise the print, PLEASE print them in the orientation indicated in the Bambu Studio screenshot in the photos. It will lead you to a successful print. Other orientations went… not quite as well. You can add a dot of glue when inserting the rails, but the tolerances are tight enough you don&#39;t need to (I didn&#39;t, for mine. I only used a touch of glue when adding the Bambu badges to the front of the holder). I did print mine with adaptive layers at the very top and the very bottom of the oriented base, just to get the best, cleanest curves that I could.

Plate holder your way (4, 6, or 8 slots)

mocodroid

Float Plane. Printed with PLA 0.4 mm nozzle, .2 mm layer height and 5% gyroid infill. I will recommend using a smooth plate for best results when gluing all the parts together. Don't glue the nose incase the propeller breaks and need to print a new one. Use a #8X1/2in screw to attach the propeller to the nose. Supports are need for the propeller, nose, windshield and the lower floats.

Float Plane

Colton

reddadsteve

Porky Pig, from the Warner Bros. Looney Tunes and Merrie Melodies series of cartoonsPorky was the first character created by the studio to draw audiences based on his star power, and the animators created many critically acclaimed shorts featuring the him. He is known for his signature line at the end of many shorts, &#34;(stutter) that&#39;s all, folks!&#34;Some supports are required on one piece, head (see notes below). If you have the proper filament colors, no painting is needed.The assembled model is 225mm tall..Enjoy!...........................................................................................................Special shoutout to maker Benoît Lussier for providing QA printing and quality feedback. Special thanks to Jason McMillan (makerworld ID Gatekeeper) for creating the Bambu Print Profile............................................................................................................**Print Instructions:** Supports: head (see notes for details) Resolution: .2mm Infill: 15% *****************Building the model**ColorsBlack: (Devil Designs PLA - Black) eyeblack_left eyeblack_right eyebrow_left eyebrow_right hoof_left hoof_right mouth words_holder ..Red: (Hatchbox PLA - True Red) tongue words tie_left tie_right ..Green: (Hatchbox PLA - True Green) base ..Blue: (Paramount3D PLA - Cadet Blue) jacket hat ..Skin: (Paramount3D PLA - Universal Beige) head hand_left hand_right body tail ..White: (Devil Designs PLA - White) cuff_left cuff_right eyewhite_left eyewhite_right .. ****************************************...........................................................................................................**Printing and assembly tips**Printing tips:1 - Supports are required on the following part: head (I used organic/tree supports, from base only, 30deg overhang)2 - There are some pieces that may need brims or rafts, use your discretion. When setting up my prints I prefer to be conservative to ensure the least chance of a print failure, especially since the base of many parts are hidden when inserted into another part. *I used a brim on: hand_left hand-right tie_left tie_right3 - When removing parts from the printer bed, it&#39;s a **VERY** good idea to place left/right parts into separate containers to help with the assembly process. Sometimes the difference between the left and right parts is very small but it is still worth keeping track of them (especially if you size up the model significantly) and assembling them in their proper place... Assembly tips:1 - Take your time gluing the model together and enjoy the process. Dry fit all the parts and give some thought into which parts to glue together as groups and then gluing the groups together. Let the glue for each group set completely before combining groups.2 - I used 3D Gloop and E6000 to put this model together. Each type of glue has different pros/cons and I found that fast drying 3D Gloop was far easier to use than superglue (for me). The E6000 sticky glue allows more time to position parts and is still the best for smaller parts. For both glues using a smaller amount is usually better than more glue.3 - Assembly is straight forward, however there are two suggestions that came up during QA: Put in the cuffs first into the jacket to ensure proper alignment before putting in the hands. Put in the tail last to avoid potentially breaking it while building the rest of the model.4 - Refer to the assembly diagrams in the pictures section as well as the uploaded pictures for putting the model together. The model is meant to be glued.Do not hesitate to ask questions, feedback is essential to making better models.

Porky Pig

dragons

SH Designs

Take professional looking photos of your 3D printed models. This tabletop photo studio light box is seamless, providing an infinite background style without corners or seams. Similar tabletop cycloramas sell for $180 at photography supply stores. Print yours for around $10 in 6 hours!&nbsp;I printed this in Bambu Basic Jade White. For black or darker color backgrounds I recommend using matte filament to prevent reflections or visible printing seams. The background can be sanded and painted for a smooth custom finish of any sheen or effect. I am going to print one with matte black and sprinkle in some stars for an infinite space background! I'll upload the photos when it is complete.&nbsp;All photos were taken with iPhone. For the light source, I used an adjustable desktop LED lamp with color temperature controls. This was perfect as I was able to move the light source easily to where I needed it. There are several affordable options on Amazon and elsewhere. &nbsp;Note: Bedslinger-type printers may need to print a little slower to prevent vibration at the top of the print. Just monitor your model for any movement in the last hour and slow down your printer if necessary to eliminate any vibration artifacts. Since printing, I made the walls 2 layers thicker than my prototype and added a rib to each end of the background to stabilize the walls and prevent vibrations at the corners, and also for added opacity.

Photo Studio Light Box

Photos

Sevro

Update: 08.10.2023I added base with holes for M3 Screws. Use it when pins in your standard Base not fit well or broke down when printed.&nbsp;OverviewI present my my ultimate plane launcher.Easy to print and assemble. You have to only fold you favourite paper plane, load, aim and shoot it to fly. You need to only 3 rubber bands to have fun with it. One small for trigger and two larger for launcher (one for each side). Launcher is projected to assembly without screws and glue but your clearence may be different than mine. If somewhere cover don't fit correctly simply use glue to fix cover to base. After proper assembly you won't have to look inside. Rubber inside handle, stays for very long. Mine didn't break yet. Rubber bands on launcher can be strech in three position depends on rubbers size and desired force.Warning: Shoot only with a loaded launcher. Shooting without a load can damage the "barrel". The occurrence of damage depends on the force of the rubbber bands.&nbsp;To print “base” and “trigger middle” use supports for rubber bands hooks. ( I often forgot about that but despite this prints went well )Below is simple schematic of assembly.<figure class="image image_resized" style="width:82.8%;"><img src="https://makerworld.bblmw.com/makerworld/draft/75491/2023-08-14_hnasrabhm0z0.jpg"></figure>&nbsp;To load correctly, the trigger must be in the up position. Often you have to set it with your thumb in the right position as in the video below&nbsp;Loading looks like that<figure class="image"><img src="https://media.printables.com/media/prints/415098/rich_content/7d798460-cad5-42ab-960a-c535ea28eb20/giphy.webp"></figure><figure class="image"><img src="https://media.printables.com/media/prints/415098/rich_content/c065fda1-dfa9-4596-a8ae-e78fc4bd9c7b/giphy.webp"></figure>And launching<figure class="image"><img src="https://media.printables.com/media/prints/415098/rich_content/8acfd9e7-f993-4ec8-970c-ed1d5692a655/giphy-2.webp"></figure>&nbsp;&nbsp;I designed small glider thar cooperate with launcher.It is available here:<a target="_blank" href="https://makerworld.com/en/models/16774#profileId-15557" rel="nofollow noopener">https://makerworld.com/en/models/16774#profileId-15557</a>and works like that:<figure class="image"><img src="https://media.printables.com/media/prints/415098/rich_content/74b00a80-1e55-4d9d-b0a8-ef45f0b99777/swift.gif"></figure>Have fun&nbsp;&nbsp;

Ultimate Plane Launcher

Fletch

Kit card for a Tyrannosaurus Rex skeleton puzzle.&nbsp;Connectors can be easily removed using just your fingers. The height of each bone and the spacing for placement both measure 2mm, providing a very snug fit.&nbsp;Various sizes availableRegular - 140mm tallLarge - 165mm tallMini - 125mm tall&nbsp;There are 2 options for each size, with or without numbers. The large size includes an optional stand, but isn't required since it's freestanding.&nbsp;Guide for the profiles with no numbers1 Plate<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/622215/2024-02-27_a5515f1741b418.png"></figure>&nbsp;3 PlatesCard 1<img src="https://makerworld.bblmw.com/makerworld/draft/622215/2024-02-23_5afd920d6cbc28.png">&nbsp;Card 2<img src="https://makerworld.bblmw.com/makerworld/draft/622215/2024-02-23_8c4c08b3381f78.png">&nbsp;Card 3<img src="https://makerworld.bblmw.com/makerworld/draft/622215/2024-02-23_1e395fd60645a.png">

T-Rex Skeleton Kit Card

kit cards

FallenAngel

Suspended 3 (Moon)

Space

designs.by.Marcum

The perfect way to bring your favorite wildlife species into your home!&nbsp;Wildlife Conservation is a topic that has been very near and dear to my heart since I was a small child, so it was only a matter of time for me to expand my Kit Card series to include various wildlife species. As the same with all of my others Kit Cards, these designs are simple and easy to print, but instantly recognizable as your favorite animal.<blockquote>In the universe are billions of galaxies, in our galaxy are billions of planets, but there is Only One Earth. It is important to remind ourselves that we only get one chance to protect and conserve the natural beauty of this world, and it is my absolute pleasure to bring awareness and life to some of the species that are most endangered of never being seen again.</blockquote>Current species included:<ul><li>African Forest Elephant</li><li>African Lion (Male and Female)</li><li>Dromedary Camel</li><li>Giant Panda (P)</li><li>Hippopotamus</li><li>Linnaeus&#39;s Two-Toed Sloth (P)</li><li>Llama (P)</li><li>Meerkat (P)</li><li>Mountain Gorilla</li><li>Polar Bear</li><li>Ring Tailed Lemur (P)</li><li>West African Giraffe</li><li>White Rhinoceros</li></ul>Animals above marked with “(P)” are located exclusively on Patreon, link below.&nbsp;The kit card connectors were designed to easily snap away, but for the cleanest finish it is recommended to use snips to remove them. Each animal may have a slightly different assembly, but the fundamentals remain the same amongst all of them.<ol><li>Snap all connectors to free each piece</li><li>Slide the ears into the cutout at the top of the head<ol><li>There are animals (such as the Lion and Gorilla) that use pegs and holes instead. For these you simply place the peg through the hole in the body and then squeeze the other side onto the peg.</li></ol></li><li>Slide the larger connector into the cutout at the front of the body</li><li>Slide the smaller connector into the cutout at the back of the body</li><li>Align to the two cutouts on the legs with the connectors and slide in</li><li>Repeat for the last leg</li><li>Enjoy!</li></ol>&nbsp;If you&#39;d like access to a Commercial License and exclusive designs not available anywhere else:<a target="_blank" href="https://patreon.com/designsbyMarcum" rel="nofollow noopener">Join me on Patreon</a>&nbsp;Filament used in product photography:<ul><li>Overture Matte PLA - Black</li><li>Overture Matte PLA - Light Gray</li><li>Overture Matte PLA - White</li><li>Overture Matte PLA - Light Brown</li><li>Overture Matte PLA - Chocolate</li><li>Overture Rock PLA - Rock White</li><li>Prusament PLA - Galaxy Black</li></ul>This community generated approximately $179 worth of points and boosts during the Animal Frenzy contest! On behalf of you all, I have donated $200 to the Fort Worth Zoo to assist in their conservation efforts. Thank you for all who took the time to show their love and support for my work.<blockquote><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000447508/design/2024-05-26_df146c068f725.png"></blockquote>

Wildlife Kit Card - Multiple Species

Minis

Nikodem Bartnik

This is a simple model of gear for 775 motor that I designed to test how durable it is. It is a part of a bigger project that I am working on now. Maybe someone will find this project usefull. Easy to print and assemble and gives you a really good result. 775 motor is super cheap and powerful motor that has high torque and can be used in any robotics project, some people even build saws and lawnmowers with this motor! This gear gives you even higher torque :) YouTube: <a target="_blank" href="https://www.youtube.com/nikodembartnik" rel="nofollow noopener">https://www.youtube.com/nikodembartnik</a> Instagram: <a target="_blank" href="https://www.instagram.com/nikodembartnik/" rel="nofollow noopener">https://www.instagram.com/nikodembartnik/</a>

775 motor gear

gaers

Kardes.Design

I'm excited to introduce my mini spool organizer. This solution allows you to easily organize and showcase your filaments with customizable labels that can be easily created using MakerLab's <a target="_blank" href="https://makerworld.com/en/makerlab/makeMySign" rel="nofollow noopener">Make My Sign</a> tool. Whether you're looking to impress friends, family, or customers, this compact and convenient system is the perfect way to keep track of or show off your filament collection. The mini spools feature a thread design to assemble them easily. The labels just slide in without glue as well.&nbsp;Available in two case sizes - one that can hold 20 spools and another that can hold 14 that can be printed on the A1 Mini. Magnets can be added to secure the case if desired.&nbsp;Case types:<img src="https://makerworld.bblmw.com/makerworld/draft/318028/2023-12-25_4b954347fa4e2.jpg"><ul><li>20 spools case printable on the X1/P1/A1</li><li>14 spools case printable on the A1 Mini</li><li>Both cases feature versions supporting 5x1 mm, 5x2 mm and 5x3 mm magnets. its perfect if you are on the move and want something more secure. You do not need to fill all the magnet holes. I added extra holes for different magnet strengths</li><li>Both cases can be printed with a version without magnet slots that can store the spools perfectly at home or in your workshop.</li></ul>Instructions:I have uploaded print profiles for every single type of box.What to print?<ol><li>Box</li><li>Spool (Amount depends on your needs)</li><li>2 spool covers ( for each spool)</li><li>Spool Label (Amount depends on your needs)</li><li>Box Label (X1)</li></ol>&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/318028/2023-12-25_8dc31f2028f77.jpg">use one label or 2 based on your needs.Labels printed with a 0.2 nozzle can print text small enough to fit the brand, material and color of the spool on a single label.Labels printed with a 0.4 nozzle can only fit Brand/Material or Material/Color on a single label.I included a spool cover without a label slot incase you are using the 0.2 nozzle and would only need 1 label per spool.<img src="https://makerworld.bblmw.com/makerworld/draft/318028/2023-12-25_960a4c8784327.jpg">If you are using a 0.4 nozzle i suggest using spool covers with labels on both sides&nbsp;Labels:Spool label:Height: 14 mmWidth: 47 mmBase Plate: 1mmCorner radius: 2 mmNo border<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/318028/2023-12-27_d4561a3b27d13.png"></figure>Box label:Everything is the same besides the height of the labelHeight: 19,6 mm <img src="https://makerworld.bblmw.com/makerworld/draft/318028/2023-12-25_c9b1c31b5751f.png">&nbsp;An added benefit of using <a target="_blank" href="https://makerworld.com/en/makerlab/makeMySign" rel="nofollow noopener">Make My Sign</a> is that the tolerances can be changed easily by you if the label does not fit. maybe your filament or printer is not calibrated correctly. But no worries. If the label is too tight for example then just decrease the height by 0.1 mm and try again. or the thickness can be adjusted by 0.1 mm.&nbsp;They can be printed without the AMS with just a pause print. I suggest you print multiple labels at the same timeI added label examples in the raw files.&nbsp;Powered by Make My Sign from MakerWorld(makerworld.com/makerlab/MakeMySign)&nbsp;&nbsp;Hi, I'm a student and love creating functional and beautiful designs optimized for 3D printing.if you like my work consider supporting me with these options:<ul><li><a target="_blank" href="https://www.paypal.com/donate/?hosted_button_id=6VL4LD2NAJJ86" rel="nofollow noopener">Paypal</a></li><li><a target="_blank" href="https://www.buymeacoffee.com/KardesDesign" rel="nofollow noopener">Buymeacoffee</a></li><li>Commercial use license: <a target="_blank" href="https://www.patreon.com/user?u=103482126" rel="nofollow noopener">Patreon</a></li></ul>&nbsp;&nbsp;&nbsp;

Mini Spool Organizer: Make My Sign

Important

engine

baris.ayarkan

Nice elephant because of the sitting it easy to print not need support only couple layers under its leg. I made 2 size 4 inch and 7 inch as an options but free to play with. Enjoy

Sitting Elephant

minis

Staprin3D

the box can be printed fully assembled on the building board (print in place) I designed it as a lunch box (180x120x60 mm), but you can also use it very well as a sorting box with the help of the insert boxes that I have included in the second print profile. The box can be easily scaled down (only proportional) and is still print-in-place capable. However, it should then be printed with 0.12 layerIf the lid catches a little when opening, a little lubricant spray will help at the beginning.

Lunchbox  or Organizerbox print in place

boxes

Eminent3D

This is one of my most refined designs i use everyday. Its a bit box for ¼" bits and a standard bit extension. The design uses Magnets (As do all my box designs) You can put the 4mmx2mm magnets in each hole if you would like, it makes for a nicer case where the bits stay put, but it is a bear and takes time and patience. &nbsp;Magnets needed for the lid are 8mm x 4mm (4)For each bit hole hole and extension are 4mmx2mm (107)&nbsp;If you buy these magnets in a larger pack then you can also use them on my other box design which use the same size magnets.

Best Bit Box (Print In Place)

tools

calebgomer

All the fun of a suspended object, with the clear suspended filament being a fiber optic, lighting up itself and the center ring!&nbsp;To print, the “Fiber” and “Rings” objects should both use the same material. However, two separate filament entries should be used in your slicer, like this:<img src="https://makerworld.bblmw.com/makerworld/draft/496349/2024-02-04_bf66f5d9dab4b.png"><img src="https://makerworld.bblmw.com/makerworld/draft/496349/2024-02-04_6bab5dfd9bfbe.png">When printing, if using an AMS, select the same filament for both:<figure class="image image_resized" style="width:49.56%;"><img src="https://makerworld.bblmw.com/makerworld/draft/496349/2024-02-04_eea6ae40c7aeb.png"></figure>This ensures the slicer properly handles the fiber strands. if this step is skipped, the strands may not properly attach at the center: <img src="https://makerworld.bblmw.com/makerworld/draft/496349/2024-02-04_390588a84b95f.png"><img src="https://makerworld.bblmw.com/makerworld/draft/496349/2024-02-04_84a3b387ef31a.png">&nbsp;<figure class="image image_resized image-style-side" style="width:27.42%;"><img src="https://makerworld.bblmw.com/makerworld/draft/496349/2024-02-04_464224fb02d08.jpg"></figure>Once printed, insert an LED light strip through the hole in the bottom, and loop it around the outside of the ring once or twice, facing the center. Tape or glue the lose end of the light strip so it doesn't come off.&nbsp;

Suspended Iris - Fiber Optic Lamp

Lights

STomHacks

UPDATE : 08/02/2024 - Fixed the closed rails on Vallejo 1x5 module and removed holes on bottom part of the modules I wasn't happy with the models available to organizer my paint bottles, I decided to create my own design with this modular paint rack system. With this system you can assemble the modules you want for the different sizes of bottles like Vallejo, AK or citadel paints. It's easy to assemble and they're available in different numbers of bottles per module.  If you have some suggestions or ideas you would like to see don't hesitate and I can create more modules.  To avoid using to much filament for these prints I suggest to use a 20% infill Lightning increasing the wall loops to 4 and the bottom shell layers to 5.

Vallejo / Citadel modular Paint rack

Queue

liljohn406

**CHECK OUT V2 HERE** <a target="_blank" href="https://makerworld.com/en/models/185439#profileId-204181" rel="nofollow noopener">https://makerworld.com/en/models/185439#profileId-204181</a>**ALSO CHECK OUT MY RISER DRAWER SYSTEM HERE**  https://makerworld.com/en/models/185440#profileId-204184After many iterations I finally got something I am happy with. I used a led strip that is powered by USB and plugged it in the 5V plug behind the screen on my P1P/P1S. There are access holes on both sides to run cabling/led strip. Open pocket behind logo to stash some lights to illuminate it. Vents only on the sides with a sliding doors built in. Which are held down by the glass. Front logo is a seperate piece to save time and filament. Only two color changes this way opposed too many if it is part of the model. Picture was printed in Bambu Matte Black and Bambu Green. 3mf is set with slower outer walls to prevent bulging and poor overhangs at top of hexagons.

Sliding Vents Riser With Led

Slowpoke's Workshop

made this cute little guy for Valentines day

Mr Heart & Miss Heart Family 

Valentine 

3D Print Masters Hub

Mini Bin Box Organizer Hanging System with options for A1,P1, X1 and A1 Mini Great for sorting supplies and accessories or more!1. Wall mounted rail - LONG or SHORT suited for A1,P1, X1 and A1 Mini. 2. Countertop shelf - LARGE or Small suited for A1,P1, X1 and A1 Mini. 3. Bin can be stacked on its own without rail. 4. Internal bin size 100mm x 56mm (4&#34;x 2.25&#34;) 5. Scale up as needed. 6. 3MF file is configured to print:-with 3 walls and brim all parts.-tree support for bin rear hanging tab only.Please like and subscribe! More to come!🔥🔥 Check out my PRO MODELS HERE! <a target="_blank" href="https://cults3d.com/en/users/FabulousFilaments/3d-models" rel="nofollow noopener">https://cults3d.com/en/users/FabulousFilaments/3d-models</a> 🔥🔥&nbsp;

Mini Bin Box Organizer Hanging System

Bins

YGPark

Contains all optional files. Choose a form that suits your condition and print it out!!&nbsp;&nbsp;>Function1. Additional exhaust fan If you turn on the left switch, the LED lights up continuously The exhaust fan can be switched on, off and speed controlled using the exhaust motor controller next to it. However, since it is a low-cost motor, it only works when a certain voltage is applied.. It needs to be about 85% of the controller to start spinning. Subsequently, fine movement will adjust the speed. I bought another speed control fan because of the speed control part, but it was in the same condition, so I just finished with this product. (It took about another week because of this.) TT As another solution, mark2 is planning to add a temperature change sensor to allow the exhaust fan to operate and stop automatically without adjusting the speed.2. 2. LED Low-heat LEDs were applied to prevent them from breaking down under the influence of internal temperature, and for even light distribution, they were applied at a 20 degree angle. 0.76w x 6 pieces = 4.56w per piece.3. a thermometer The temperature of the upper part of the chamber can be checked by applying a needle-type thermometer. (You can take it out while cooking.)4. You can adjust the right lever to adjust the amount of heat exiting the rear top exhaust. Due to the strong performance of the additional fan, the hole was not made large to maintain the temperature inside the chamber.5. window partition vent It's a size that fits my fancy. I attached the f3d file, so you can pull it out according to the height of your window frame Even if you increase the chamber fan speed to 100%, the air suction snout is at the height of the extruder, so you can't suck the hot heat above that. In particular, the PLA is vulnerable to heat, which requires opening and printing the front door, so adding an outlet at the top allowed the door to be closed and output.It was built within 60mm to make the most of the space behind the printer.The temperature at the top of the chamber was maintained at 46-48 degrees. We are planning to match this part by applying the temperature sensor at mark2.The outlet plug is foreign, so it's thin, so it doesn't get tight. It's a good idea to exchange products that you throw away at home or on the radio. Or wrap it with tape so that the plug doesn't come offAll options are modular, so you can select and install only what you want. If you don't need an LED, you can take out the frame and print it out If you don't need a thermometer, don't plug it in~ To install the additional fan on the window side rather than behind the printer, pull out the 100mm external diameter and 100mm internal diameter adapter, respectively, and move them again. Since the fan controller (FWM) is not functioning properly, you can only turn it on and off without a controller.The AMS is designed so that it does not affect the bending of the rear tube even when setting is placed on the printer. >Main points when assembling It is recommended that you lay it on the floor first and then put it on the chamber. 1. Plug the power on/off switch into the fan's wire first to hold the line length. Connect the wiring as shown in the picture. Fan = Plug-Switch-Controller-Pan LED = Controller-Inverter-LED Pass the wires from the switch and the wires from the inverter in one place. Hand over the wires to the fan to the other two slots. The wires are relaxed, so don't make them too tight. If you fold the spare parts into the frame later, they will be neat. 2. Pull and pull the controller adjustment knob, assemble it to the case, and plug the knob back in. 3. Never cut the wire and adjust the length with LED wires as it has holes to match the length of the inverter's wiring~ 4. Use the 'Tree' support when extracting the vent3 file and carefully remove the parts when removing the support. 5. Insert the magnet by setting 'Pause' by pressing the right mouse button at the first layer where the hole is covered in the preview slicing state. 6. The Extruder Tube Guide must be installed. https://www.printables.com/model/338542-x1-p1p-ptfe-tube-guide-to-fix-loading-issues-best-&nbsp;> Purchase ListController https://ko.aliexpress.com/item/1005004180917280.html?spm=a2g0o.order_list.order_list_main.23.5faa140fPiDN3o&gatewayAdapt=glo2kora blast fan https://ko.aliexpress.com/item/1005004354219502.html?spm=a2g0o.order_list.order_list_main.58.5faa140fPiDN3o&gatewayAdapt=glo2korLED / Inverter Epoxy type 3-hole module KPL Korean 30w (165x24x18mm)neodymium magnet Magnet size: D15Xd7.3X15TThermometer Advanced Cooking Thermometer (Automatic Off after 10 minutes) https://ko.aliexpress.com/item/1005002322143988.html?gatewayAdapt=glo2kor - Hardware store bellows duct 100 mm Cable ties (or anything you can tie to your house or electrical tape)

Vent for P1S by YGP

FilliFuu

Cute Baby Dragon Keychain. Fits any basic ring keychain, can be brought cheap on amazon (pack 100 - $5)&nbsp;Enjoy & any problems please let me know.<h2>3D PRINTING SETTINGS</h2>Supports not needed, no brim but you can enable if you want a cleaner print.0.3 walls, wall speed 90

Flexi Cute Dragon Keychain

keychain

J1136_

A simple business card organizer/holder, hollowed for the sake of faster print speed. takes roughly 40 minutes to print on standard speed.  (Is designed for the standard card size, but allows for bigger sizes)&nbsp;

Fast Printing Business Card Holder

office

Speedy 3d

This is an excellent way to organize parts, screws, and tools. It can be printed thicker as it is used for craft and takedowns. You may insert the new tray design for contrast of color and a replaceable work surface. Print this surface so the PEI steel texture shows!

V1 Tool & Tech Organizer Work Mat  (TPU Insert)

Must Have

dalet11

Flexible Dachshund&nbsp;Thanks to MrHanjak for this model :)&nbsp;Profiles for multicolor (painted eyes) or single color are available.&nbsp;

Flexi Dachshund - DOG

Flexi

Maty505

articulated lizard with crystals. best result with silk, color changing or rainbow filaments

Articulated Crystal Diamond Lizard

Dragons

laisch

Invisible mounting bracket for mounting a shelf to the wall and get this floating shelf effect.For alignement there are two holes wich fit an M3 heat insert and some M3 screwsIf you are using a CNC for milling the space for the insert, you can use the provided dxf file.

Hidden Shelf Mounting Bracket

useful

Roland Deschain

My printing profiles for Overture TPU on the Bambu Lab P1P that you can use as a starting point. The 3MF includes both a filament and 0.20mm process profiles. If you come up with better settings I would love to hear about them in the comments.&nbsp;Warning: If you print a third party profile you may not be getting the latest version or the highest quality print. &nbsp;If you like this project, please don't forget to ❤ Like and ★ Rate!

Overture TPU Filament and Process Profiles (Bambu Lab P1P)

Profilea

Brandido02

The rims and center ring are straight from Bambu's spool. And interchangeable with it. It is designed for Bambu's refill spools. But I have found that Elegoo spools also fit perfectly on it. Also Overture and Polymaker spools fit but are a bit loose, but they fit perfectly over the center rings of Bambu and Elegoo spools. So, I use them as spacers. Let me know if you try it with any other brands!I recommend PLA because it is a lot stiffer than PETG.&nbsp;03/24/23 - I've got multiple requests, so I uploaded a version 2.3 and 3.3 that remove the little notch on the inner ring. I left print profiles with versions 2.2 and 3.2 that still have the notch for Bambu spools. Note, I think the notch is important because it locks the cardboard inner ring so it doesn't spin free of the spool. &nbsp;12/14/23 - WOW 7K Downloads!!! Some folks asked for a filament scale, Soooo here is v2.2 and v3.2!!! The left side of both have a filament scale. The right side is unchanged.&nbsp;11/19/23 - Here is v2.1 and v3.1!!! The only difference is I added a 2mm hole in the Left side of the center ring for filament to be inserted when respooling. Though respooling isn't what I usually do. I actually have found that the cardboard center of other spools fit right over the center of this spool. Specifically, Elegoo fits perfectly. you just need to nip out a little notch. I have also done it with Overture and Polymaker. but their center rings are a little bigger and so are a bit loose. But, the center ring of an overture spool fits snugly right over the center ring of an Elegoo spool, which fits snugly over the center ring of this Bambu spool!&nbsp;10/19/23 - Wow! 3K downloads! Here is Version 3! it uses less filament and takes less time. But it may not be as strong. I have been testing it now for a couple weeks without any problems.&nbsp;9/29/23 - Uploaded v2. I completely remade the spool using Bambu's newest spool. The rims are completely smooth now.&nbsp;Here is a remix of Bambu's Filament spool but with hexagons to use far less filament without sacrificing strength.The rim filament holes are also angled so as not to introduce a sharp bend into the filament. Also, there are more of them around the rim.This is interchangeable with the original Bambu rims.&nbsp;Note: the spacing shim goes on the inside of the spool to lock the two halves together. Though I haven't needed it because they lock together pretty tight. But Bambu recommends it, so I included it.&nbsp;Why hexagons? Because hexagons are the best-agons!&nbsp;Notice: Print profiles NOT created by Brandido02 may contain outdated model versions or suboptimal slicer settings. Use at your own risk! I have no control over these third-party print profiles.

Bambu Reusable Hex Spool

Spools

Ten Minute Tech

Hello!&nbsp;I wanted to change the color of my AMS hub cover, and I figured others may want to do the same. &nbsp;This is my by-hand re-imagining of the AMS hub cover so that you may use it for your mods or reprint it to change the color of your hub. If you remix for your mods please acknowledge my original! This one has been fit tested and seems to work fine when printed with my associated print profile. YMMV though! The AMS and filament path is a finicky beast so please be careful opening up your hub!&nbsp;WARNING: If you open up your AMS hub, you need an auxiliary magnet, so you can place other magnets. Be sure to check the wiki on how to do this. If you open it up without a magnet things will go flying and you may lose the springs for the filament sensor. &nbsp;I might produce a youtube video on my channel discussing the process of the basic CAD and build if there's interest, let me know in the comments here. &nbsp;Thank you and have a nice day!

AMS Hub Housing Cover

zuperbuuworks

<h4>IMPORTANT: If you use a P1S/P1P and experience issues printing the top of the head, please configure the print profile speed to 80mm for the outer wall, and give the model 3 walls. (thank you user PavorMaker who helped figure this fix out.) If you use the Textured PEI plate, a brim is necessary regardless of what machine you use. A brim is not needed if you use the Cool Plate in an enclosed machine, that has a stable temperature.</h4>This Kohaku model comes in two sizes; short, and long. The short dragon has 14 joints down its body, the long has 25 joints.The whiskers are just strips of filament that I have glued into the holes on the side of the muzzle, a filament size of 1.75mm fits in the holes nicely.Due to the limit of 4 colours, the pupils are not black. A dab of acrylic or permanent marker works fine.I printed mine without a brim; providing your hotbed is clean/freshly glued, you shouldn't need a brim either.&nbsp;Supports are not needed, so don't print it with any or you'll end up wasting filament and risk damaging the joints when removing supports. If you are having issues with the toes/claws not printing well, do the following:<ol><li>Turn supports ON.</li><li>Set the type to “normal(manual)”.</li><li>Set style to “snug”.</li><li>Tick the box for “touching buildplate only”.</li><li>Paint the base of the palm/fingers/toes in support paint mode.</li></ol>This way only supports are generated on the hands, and not anywhere else.You can add another two segments to the LONG version tail and neck to make it longer, but due to limited space on the hotbed, I wouldn't make the model itself larger. I wouldn't print it any smaller as the joints will likely lose strength.&nbsp;Pre-painted/coloured versions are also available!&nbsp;The joints can move in almost all directions. The arms and legs do not move.You can see the range of movement in this video:<figure class="media"><div data-oembed-url="https://youtu.be/xSSe9JOoXks?si=4sJp5R7leFCYHIMg"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/xSSe9JOoXks" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;This file covers PERSONAL use. If you want to sell prints of this model, please subscribe to my Patreon: https://www.patreon.com/thomastedwards

Articulated River Spirit Dragon Toy

articulated 

Amao Chan

A hungry polar bear fails to reach the fish held in the naughty seal’s mouth. Everytime the polar bear tries to catch the fish, the seal will sink back into the water and tease the poor, hungry polar bear.&nbsp;In fact, polar bears are indeed always famished because of the worsening condition of the planet due to global warming, and the North Arctic has become warmer than usual. On top of this, the melting of the ice has shrunk the polar bears’ living area, and made it difficult for them to hunt. There are many signs telling us that polar bears and the polar ice caps are slowly disappearing.&nbsp;The design, Polar Bear with Seal, was a paper DIY for the magazine Young Scientist. I really liked the concept, so I redesigned it into STL files. I hope this piece of art can convey a sense of beauty both in motion and stillness. While I was designing this, I put a lot of effort into observing the subtle changes in the movements of polar bears. In order to make this design work via 3d printing, I adjusted every component’s angle. Very few parts require supporting material.&nbsp;Ultimately, this art piece took me the longest time to design, and it’s the most complex one I have ever shared. I am extremely happy with the outcome!&nbsp;<a target="_blank" href="https://youtu.be/2ga2XGnS2OA" rel="nofollow noopener">https://youtu.be/2ga2XGnS2OA</a> <a target="_blank" href="https://youtu.be/UWyBoHDMF1g" rel="nofollow noopener">https://youtu.be/UWyBoHDMF1g</a>&nbsp;Thanks to SpiderMaker for sponsoring the creation of this work.<a target="_blank" href="https://www.amazon.com/SPIDER-MAKER-Matte-Printer-Filament/dp/B07HX9DY9F" rel="nofollow noopener">https://www.amazon.com/SPIDER-MAKER-Matte-Printer-Filament/dp/B07HX9DY9F</a>&nbsp;Material used SpiderMaker PLA Matte Paper White/Matte Iron blue/Matte Steel Blue/Matte Orchid Purple/Matte Peacock Green/Matte Coal Black&nbsp;Print suggestions 1.Layer height 0.2mm 2.Low down the flow to 90%or 95%. 3.Add oil on moveable parts&nbsp;<a target="_blank" href="https://amaochan.work/" rel="nofollow noopener">https://amaochan.work/</a> <a target="_blank" href="https://www.facebook.com/paperworkers/" rel="nofollow noopener">https://www.facebook.com/paperworkers/</a>&nbsp;北極熊與海豹調皮小海豹從浮冰的縫隙中探出頭來，用嘴中叼的魚逗弄著北極熊；當飢餓的北極熊揮掌搶魚時，海豹總是快一步的把頭縮回海面下，看樣子吃不到魚的北極熊要餓肚子了。 事實上，北極熊真的是處於挨餓狀態中！全球暖化，北極氣溫不斷上升，造成北極的海洋冰層融化，使得北極熊的活動範圍縮小、食物變少、獵食變得困難，許多跡像顯示北極熊正和北極海冰同時消失中！&nbsp;《北極熊與海豹》這個作品，原本是我為《科學少年》雜誌所設計紙製DIY作品；我很喜歡這個有趣的構想，所以把它重新設計為stl的版本。我希望這個作品在動與靜都能呈現美感，所以在設計時，特別注意北極熊在姿態上的微妙變化。為了配合3d列印工具的特性，調整了每個零件的角度；只有很少數的零件，在列印時需要設定支撐。《北極熊與海豹》是我目前分享的作品中，耗費時間最多、設計難度最高，但最後的設計成果，我很滿意！&nbsp;感謝 SpiderMaker 織造者 贊助本作品之創作&nbsp;使用材料 SpiderMaker PLA 消光白色、消光鐵灰藍色、消光鋼青色、消光蘭紫色、消光暗綠色、消光黑&nbsp;製作建議 1.層高0.2mm 2.流量降到90-95 3.組裝完成後在移動零件加些潤滑油。

Polar Bear with Seal (automata)

Animals

TripleGWorkshop

Get the whole set!> <a href="https://www.printables.com/@TripleGWorkshop/collections/655985" rel="nofollow">https://www.printables.com/@TripleGWorkshop/collections/655985</a><figure class="image image_resized" style="width:94.44%;"><img src="https://makerworld.bblmw.com/makerworld/draft/120213/2023-10-26_bafjltirnyjm.jpg"></figure>&nbsp;

⌇⌇⌇ Mesmerizing Vase Set - Wavy

Vase Mode

morfaber78

Happy HalloweenSkull suspended - PLA orange neon transparenttwo perimeterslayer height 0,25infill 15%no brimno supportthin wallas activatemonochrome or multicolor file&nbsp;For print FDM

Happy Halloween - skull suspended

Print Queue

Teixi3D

I bring you a painted style Super Mario model, created with HueForge. I hope you like it!!&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used: PLA PolyTerra Charcoal Black Transmission Distance: 0.3 PLA PolyTerra Pastel Watermelon Transmission Distance: 1.5 PLA PolyLite Pro Light Blue Transmission Distance: 1 PLA Protopasta White Transmission Distance: 3Swap Instructions: Start with Charcoal Black At layer #7 (0.64mm) swap to Pastel Watermelon At layer #15 (1.28mm) swap to Light Blue At layer #22 (1.84mm) swap to White for the rest.

super mario painting (HueForge)

Hueforge

WF3Dprinting

Please measure your drawer before printing. These are made for the drawers with a exact width of 29,5 cm. Apparently there multiple version of the IKEA Alex with different dimensions. If yours is wider they will be quite loose and you'll need some extra material for the right fit.

IKEA Alex Drawer divider

Orginjzation

CUBEIFY

I don't have much room around my P1P as im building it in a display cabinet and so set about creating a spool mount for the top of the frame which also allowed feeding from the front. This will easily hold 2x 1Kg spools aslong as it is printed correctly. Most standard 1Kg spools should fit, you may need to create a spacer for those with a large center bore to ensure clearance over cable chain. The design does not impede on any tool head clearances at the rear of the frame (Nightmare)I printed the arm and load bar with adaptive layer height, 6 walls 40% cubic infill. Other pieces should be solid at 6 walls.for maximum strength i recommend printing the arm on its side but with good layer adhesion the back of the arm should be fine.PLEASE STRESS TEST YOUR ASSEMBLY HOLDS WELL BEFORE PLACING ANY SPOOLS ON IT!!!Requirements:<ul><li>Minimum PETG for heat resistance</li><li>PTFE Passthrough with cable chain - Should work with most existing designs but <a target="_blank" href="https://makerworld.com/en/models/23190" rel="nofollow noopener">My design</a> is confirmed</li><li>Y Splitter - Any should work but i can confirm <a target="_blank" href="https://www.printables.com/model/302647-bambu-lab-x1-y-splitter-with-inlet-for-pneumatic-c/files" rel="nofollow noopener">this design</a></li></ul>Hardware:<ul><li>2x M4x6x6 Heat Set Insert</li><li>2x M4x10 Bolts (Hex for easier install)</li><li>5x M10 PTFE Connector (3 for Y splitter)</li><li>Glue (or melt with iron)</li><li>PTFE tubing</li></ul>Assembly:<ol><li>Install M4 Insert into Arm under the hexagon</li><li>Install M4 Insert into Clamp</li><li>Locate and bolt Load Bar to Arm</li><li>Install M10 PTFE connectors into the 2x PTFE Holders</li><li>Glue PTFE holders into the top of the Arm base with the PTFE Conectors facing the rear</li><li>Place the arm on the back center of the frame locating the lip on the top edge first</li><li>Slide Clamp inside the frame lining up 2 notches at the front and bolt through frame</li><li>Install PTFE tubes & Y Splitter (I removed the floating screw from the original PTFE join)</li></ol>Use photos for reference :)<a target="_blank" href="https://makerworld.com/en/models/23188" rel="nofollow noopener">ARC compatible version posted as a remix to the enclosure</a>&nbsp;

P1P Top Spool Holder

Bambu

Bambi

Hobbypunk

I created a HSW modplate inspired by Bambu Lab Armor Modplate

Bambu Lab P1P HWS Armor Modplate

Modplates

BODY3D

If you like my work, support me by leaving a like !Get access to really cool models every months on my PatreonAnd don't Forget to Follow me !<a target="_blank" href="https://www.patreon.com/BODY3D" rel="nofollow noopener"><img src="https://dreamityourselfmusician.com/wp-content/uploads/2020/10/patreon-france.jpg" alt="BODY3D"></a><a target="_blank" href="https://www.tiktok.com/@body_3d" rel="nofollow noopener"><img src="https://encrypted-tbn0.gstatic.com/images?q=tbn:ANd9GcSrfIHeAYT6KeLQTVHxvXORYsILY6oVXlNVmg&usqp=CAU" alt="BODY3D"></a> <a target="_blank" href="https://cults3d.com/en/users/BODY3D/3d-models" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/user/3079230113/draft/2023-08-21_6b0967a6c4cbc.png"></a> <a target="_blank" href="https://beacons.ai/body3d" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/user/3079230113/draft/2023-08-21_63b5664660755.png"></a>

Mr Banana

Funny

squinn

A helpful lid that you can screw onto a standard mason jar to create the perfect fruit fly trap. Put a bit of liquid bait inside (just about 5 mm deep), and place where it's needed. &nbsp;There are many commercial fruit fly liquid baits available, or you can just use a bit of apple cider vinegar or wine. The flies are attracted to the smell of the bait, and then after entering the jar are unable to find a way to fly back out. You can also add a few drops of dishwasher detergent to the bait if you'd like, which will cause the flies that land on it to drown (as they get caught in the surface tension of the liquid.)&nbsp;This is an easy print that requires no supports (it's designed to be printed upside down, as the STL is oriented.)

Fruit Fly Trap Mason Jar Lid

Household

V3 Precision

This is a spool winder for transferring filament from one spool to another. Inspired by the need to use certain filament spools for the Bambu Lab AMS. This build should speed up the process and give a nice tight winding. There is room for improvement, so feel free to give some feedback either on Printables or on the Youtube videos.This version is 100% 3D printed (not including the mounting screws). Future versions will use bearings and possibly a motor to drive the gears.The images show the assemblies mounted to a 2x6 for testing. The assemblies can be mounted to a similar board or to a base made from aluminum extrusions.&nbsp;Printing RecommendationsI used PLA while developing the spool winder. I would recommend using PETG, or Nylon CF, or other stronger, stiffer filament.The ‘worm’ gear can be tricky to print. In Bambu Lab Studio, I set the part upright and set support to tree (auto) and threshold angle at 10. Set a brim at 8mm.The gears are easy to print and require no support or post processing.The bases need some support and did well with tree (auto) and threshold angle of 30.I used 4 walls and 15% infill on most pieces. The thumbscrews I used 100% infill.&nbsp;AssemblyMost of the assembly is easy and self-explanatory.Note that the rear driven gear is reverse threaded.Specific instructions can be found in an upcoming Instructions Video …….There will also be a link to the video on the V3 Precision website.&nbsp;#best3dp2023<figure class="media"><div data-oembed-url="https://youtu.be/3llHdgb1ftQ?si=rh9tLXTMeOSzBDXe"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/3llHdgb1ftQ" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure><figure class="media"><div data-oembed-url="https://youtu.be/ru2TtLahlmw?si=5opj3V5R-Ab6cPFX"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/ru2TtLahlmw" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

Filament Spool Winder

3d printing

DonMatis

Would you choose to pass the portal that leads to another dimension?&nbsp;Filament painting made by HueForge. This model contains black background to promote the rest of the design.&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used:<ul><li>PLA Overture Black</li><li>PLA PolyTerra Charcoal Black</li><li>PLA Overture Cement Gray</li><li>PLA+ Sunlu Gray</li><li>PLA Overture Light Gray</li><li>PLA PolyTerra Cotton White</li><li>PLA Overture White</li></ul>Swap Instructions:<ul><li>Start with Black</li><li>At layer #7 (0.64mm) swap to Charcoal Black</li><li>At layer #9 (0.8mm) swap to Cement Gray</li><li>At layer #11 (0.96mm) swap to Gray</li><li>At layer #14 (1.2mm) swap to Light Gray</li><li>At layer #18 (1.52mm) swap to Cotton White</li><li>At layer #22 (1.84mm) swap to White for the rest.</li></ul>

Portal

JamesThePrinter

Cylindrical container covered in spikes!&nbsp;&nbsp;Print SettingsVase mode required. Personally, I prefer to use thick perimeters in vase mode for added strength.&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The following filaments were used in the pictures above:<ul><li>MatterHackers Quantum Blue Raspberry PLA</li><li>MatterHackers Quantum Blue Yellow PLA</li></ul>

Spiky Pencil Holder

Office

Jorge Rui

<h3>Introduction</h3>This model has been specially developed to take full advantage of the printing bed of most printers, which is approximately 200x200 or a little more.but it can also be used for anything else, with saving writing material, drawing etc.<ul><li>This gray module you see is specific to 100x150mm index-cards (4x6 inches). To get an idea of the dimensions, it allows you to put a little more than 700 cards of 180g/m^2</li></ul><figure class="image image_resized" style="width: 75%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013523/design/2023-08-21_xznmnldpwl14.jpg"></figure>Of course, in the case of a modular system it is possible to accumulate as many modules as you need, that is, the system will grow according to your needs.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013523/design/2023-08-21_1adne8yera7t.jpg"></figure>You can use colors for each of the groups, thus organizing your workflow.<h4><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013523/design/2023-08-21_oa9zzg75e1an.jpg"></h4>And a new 76,2x127,0mm (3x5 inches) that you can find in “3x5 module.3mf” in files.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013523/design/2023-09-26_cfcdbdafdbe5d.jpg"></figure><h4>Printing</h4>These cards are the second largest, and so as you can see the boxes are not small either (like I&#39;ve said in the beginning, they use almost all the print bed area (PRUSA MK series). You will have to wait a few hours before you can use your slip-box, but you will get it and it look fantastic. If you want other dimensions send a message or change this to your needs.It is however a remarkably simple impression, without supports, without anything special. The infill is up to you, the default 15% is ok.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013523/design/2023-08-21_phzp7i2ry0gj.png"></figure><h2>Change log</h2>(26-09-2023) - Added some tabs, maybe they help. Only 2 layer thickness.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013523/design/2023-09-26_3d743f3b1a109.jpg"></figure><ul><li>Added a 3x5 box to files.</li></ul>And a diferente application, board games sleeves and baggies, thanks to <a target="_blank" href="https://makerworld.com/en/@marco.boschetto" rel="nofollow noopener">marco.boschetto</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013523/design/2024-06-27_1e261084396fc.webp" width="1080" height="1440"></figure><h4>Support the designer:</h4>This design is free for the benefit of the community, but If you like my designs and want to contribute, you can make a donation to <a target="_blank" href="https://www.buymeacoffee.com/designrepcom" rel="nofollow noopener">buymeacoffee </a>or <a target="_blank" href="https://www.paypal.com/donate/?business=BUM67EMDJRXSN&amp;no_recurring=0&amp;currency_code=EUR" rel="nofollow noopener">paypal, </a>or even better, join “My Club” here in printables.com, that will be greatly appreciated.&nbsp;

Zettelkasten Index boxes (Slip Box)

Containers

Bambu Lab

A1 mini test model - Screw Gauge by Bambu Lab

Screw Gauge by Bambu Lab

Tools

IK3Digital

Adorable Chubby T-rex pencil holder that prints super easy and quick as it needs no supports at all.&nbsp;I recommend at least 2 walls and 12% infill.&nbsp;All of my models are for personal use but if you would like to sell them physically you can subscribe to my Patreon to get a commercial license, free models every month and a welcome package: https://www.patreon.com/IK3D &nbsp;&nbsp;

Chubby Dinosaur T-Rex Dino Pencil Holder 

Kids

SmarTiks

Articulated Dragon model made by P1lotz at https://www.printables.com/fr/model/331094-articulated-christmas-dragon