colly

SpannMagoo

I made this tool to make everyone's lives easier and less stressful when transferring filament from a cardboard spool to a ‘master spool’. In most cases you shouldn't need to do this and use one of the many adapters out there. Sometimes its unavoidable and you have to transfer the filament. I know I have been victim to receiving a spool of filament that was used is a game of kickball. Directions: Place the spool down on one of the faces on a table. Peel up one side of that side just a tiny bit and I mean a tiny bit enough to slide one side of the tool in. Now repeat this step for the other side of that side. Lock them in place with your locks and then rip the cardboard off and peel any remaining paper. If you did it right, you spool wont unwind and fit on nice and clean. Now do it on the other side and you are done. Most of the ‘master spools’ out there lock in place, don't forget to completely turn them to get them to lock. Note: You may need some flush cutters if your spool has a really long pig tail in the center of the spool. It's safe to snip close to the spool.

Filament Transfer Tool

tools

JDJDJD

The Smoothy Mount is the official mount designed for use with the <a target="_blank" href="https://makerworld.com/en/models/18174" rel="nofollow noopener">Smoothy PTFE Bowden Y Connector</a>. The Smoothy allows you to use an external spool with your Bambu Lab machine without disconnecting your PTFE Bowden Tubes.&nbsp;The Smoothy can happily rest inline without a mount which has some advantages, but some users have requested a mounting method so I'm delivering for you!&nbsp;The Smoothy Mount features a universal mounting design so it can be used with either an M3x8mm screw or magnets.&nbsp;Having the mount separate allows for easy removal of the Smoothy without removing fasteners like screws, etc.&nbsp;I've designed a couple images with placement ideas but the location and method is up to you.&nbsp;The screw mount is most secure, while the magnets allow for more flexible placement. On the X1C, the screw hole closest to the outside edge of the machine works best.&nbsp;Several magnet sizes are now supported for flexibility (see files). The magnets need to be fairly strong. If you don't have strong magnets, I recommend the screw mounting method.&nbsp;The Smoothy Mount is compatible with Smoothy models that have flanges at both ends, which includes:<ul><li>Smoothy V2 PC4-M6</li><li>Smoothy V2 PC4-M10</li><li>Smoothy V1 PC4-M10</li></ul>If you have a Smoothy V1 M6 with no flange, simply upgrade to a Smoothy V2 and you'll be good to go!<h2>FEATURING:</h2><ul><li>No Supports</li><li>No Brims</li><li>No Overhangs</li></ul><h2>NOTES:</h2>I printed all tests successfully with the following:<ul><li>Nozzle: 0.4mm</li><li>Layer Height: 0.2mm</li><li>Walls: 4+</li><li>Infill: Gyroid</li><li>Brims: Disabled</li><li>Supports: Disabled</li><li>Orientation: Vertical, wide side down</li><li>Glue Stick: Yes</li><li>Bambu Lab X1C</li><li>Cool Plate</li></ul><h2>UPDATES:</h2><ul><li>Support for several new magnet sizes has been added!</li></ul>The Smoothy can be used commercially, but can't be resold.&nbsp;Enjoy!&nbsp;Download The Smoothy PTFE Bowden Y Connecter here: <a target="_blank" href="https://makerworld.com/en/models/18174" rel="nofollow noopener">https://makerworld.com/en/models/18174</a>

tools

x1c