Chris

FiBaLi

Servus a nice looking easy to print model have fun with it share it like it

Vino o clock

Robyn

jepeda

This was updated from the original models to support the Barrina shop lights. This is a set of brackets for a modular grow tower that fits on the mounts on the outer sides of the tower. These fit the Barrina T5 shop Light <a target="_blank" href="https://www.amazon.com/gp/product/B08FD5BZ4Q/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1" rel="nofollow noopener">3&#39;</a> and <a target="_blank" href="https://www.amazon.com/dp/B01HBT3BVM?ref=ppx_yo2ov_dt_b_product_details&amp;th=1" rel="nofollow noopener">4&#39;</a> versions. Endcaps should be printed in petg and need to be slowly tapped onto the lights from the edge in. These are meant to be tight. Tapping too hard can cause the clips to snap so print extras. If you use PLA they will be two brittle to get into place. Once these are on the aluminum, and past the plastic ends of the light, they will be able to be moved with some force to their final locations. The light bar snaps into place between the tabs on the end cap. This should be fairly simple to install and requires a small amount of force to snap into place. To install these onto the mounting holes, use a 25mm m3 screw (I used stainless steel) and the included spacers. Nuts/Bolts needed:--------------------------------- 6 - M3 Bolts 6 - M3 Nuts&nbsp;

Barrina LED T5 Shoplight Mount for HydroTower

Hydroponics

Printer Accessories

planes01

<h3>Overview</h3>A-10 kit card&nbsp;Check out the <a target="_blank" href="https://makerworld.com/en/models/199176" rel="nofollow noopener">SR-71</a>, <a target="_blank" href="https://makerworld.com/en/models/242106" rel="nofollow noopener">B-52</a>, <a target="_blank" href="https://makerworld.com/en/models/436445" rel="nofollow noopener">A-10</a>, <a target="_blank" href="https://makerworld.com/en/models/402126" rel="nofollow noopener">787</a>, and <a target="_blank" href="https://makerworld.com/en/models/405459" rel="nofollow noopener">Darkstar</a>!Check out the full airplane kit card collection → <a target="_blank" href="https://makerworld.com/@planes01/collections/991821" rel="nofollow noopener">linked here</a>!<h3>Profiles</h3><ul><li>Kit Card<ul><li>plane in a kit card format ideal for gifting to others</li></ul></li><li>Model Pieces<ul><li>plane without a kit ideal for assembly right off the printer</li></ul></li></ul><h3>Filament</h3>As shown:<ul><li>Inland PLA Light Brown</li><li>Hatchbox PLA Cool Gray</li><li>Overture PLA Cement Gray</li><li>Overture PLA Space Gray</li></ul><h3>Tips</h3><ul><li>Model requires close tolerances to ensure snug but not tight or loose fit<ul><li>Make sure the model cools to room temperature before assembly</li><li>Ensure filament is properly calibrated with no excessive over extrusion</li></ul></li></ul><h3>Assembly</h3><ul><li>Remove all pieces from the kit</li><li>Debur as needed to smooth edges</li><li>Glue missile together (optional but recommended)</li><li>Let glue cure before proceeding to next step (optional but recommended)</li><li>Insert wing into forward fuselage slot</li><li>Insert engine pylon into middle fuselage slot</li><li>Insert horizontal tail into aft fuselage slot</li><li>Insert engine to pylon<ul><li>Recommend forward end first, then press down on the aft end. It will clip into place. (See gift below)</li></ul></li><li>Insert missile pylon to wing<ul><li>Recommend aft end first, then press down softly on forward end. It will clip into place. (See gift below)</li></ul></li><li>Insert vertical tail onto horizontal tail<ul><li>Recommend aft end first, then press down on the forward end. It will clip into place. (See gift below)</li></ul></li><li>Place airplane onto stand<ul><li>Recommend slot into the forward end first so that the tabs at the aft end do not accidently break</li></ul></li><li>Enjoy!</li></ul>&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000177353/design/2024-01-31_283fafe2d18ec.gif">

A10 Kit Card

Cars, Planes, Models

The Big Greek

Phone Stand 2024 Hi I would like to introduce you to my Phone Stand 2024.I think phone stands are just great. They are easy and quick to print and you can never have enough of them :-)You don't need an AMS for this one. Just print all the parts, stick them together and you're done.&nbsp;UPDATE 14.03.2024&nbsp;<figure class="table" style="width:98.39%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td style="text-align:center;" colspan="2">Complete your desk with the 2 new models in the same design as the phone stand</td></tr><tr><td>Business Card Holder<a target="_blank" href="https://makerworld.com/en/models/253496#profileId-269932" rel="nofollow noopener">https://makerworld.com/en/models/253496#profileId-269932</a></td><td><figure class="image image_resized" style="width:30.52%;"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-03-14_e8318022c0223.jpg"></figure></td></tr><tr><td>Pen Holder<a target="_blank" href="https://makerworld.com/en/models/253471#profileId-269896" rel="nofollow noopener">https://makerworld.com/en/models/253471#profileId-269896</a></td><td><figure class="image image_resized" style="width:30.09%;"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-03-14_0b91c40d9d56a.jpg"></figure></td></tr></tbody></table></figure>&nbsp;&nbsp;<figure class="table"><table><tbody><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;text-align:center;">Also check out this Phone Stand if you are interested. Split-Phone-Stand 2024 <a target="_blank" href="https://makerworld.com/en/models/169860?profiled=186535#profileId-186532" rel="nofollow noopener">https://makerworld.com/en/models/169860?profiled=186535#profileId-186532</a></td></tr><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;"><figure class="image image_resized" style="width:167.885px;"><a href="https://makerworld.com/en/models/169860?profiled=186535#profileId-186532" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-02-03_2ad417cb9457e.jpg"></a></figure></td></tr><tr><td style="text-align:center;">UPDATE 03.02.2024  Also check out this Phone Stand if you are interested. It's a 3-ANGLE Phone Stand <a target="_blank" href="https://makerworld.com/en/models/169772#profileId-186430" rel="nofollow noopener">https://makerworld.com/en/models/169772#profileId-186430</a></td></tr><tr><td><figure class="image image_resized" style="width:18.65%;"><a href="https://makerworld.com/en/models/169772#profileId-186430" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-02-03_039c3598d2fbb.jpg"></a></figure></td></tr></tbody></table></figure>If you like my work/project consider supporting me with these options:<ul><li>leave a like</li><li>leave a comment</li><li>download the file</li><li><a target="_blank" href="https://www.buymeacoffee.com/thebiggreek" rel="nofollow noopener">or By me a Coffee</a></li></ul><h3>This article/post/text or the print profile as well as the finished print may not be used for commercial purposes.</h3>Have fun printingTBG&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_16be5c7fdcb9f.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_52fde81037999.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_4c5855c0935ab.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_e3ac89cf4bdd8.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_904b0eb62ac33.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_28f2834273aa7.png"></figure>Please no commercial use

Phone Stand 2024 (No AMS needed)

Essentials and Accessories

Sevro

Update:28.03.2024 - I redesigned the lamp a bit. I made it a little thicker, so now it is compatible with 12 mm LED strip and is also stronger.&nbsp;I used to this version LED STRIP from Bambu Lab Store<a target="_blank" href="https://store.bambulab.com/collections/led-strip-light/products/white-cct-tunable-cob-led-strip-light?skr=yes" rel="nofollow noopener">https://store.bambulab.com/collections/led-strip-light/products/white-cct-tunable-cob-led-strip-light?skr=yes</a>&nbsp;&nbsp;The diffuser has a larger flange and fits better into the main ring.I enlarged each piece by 110% so it now better takes advantage of bed size of the Bambu Lab printers <figure class="image image_resized" style="width: 68.55%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/2024-03-28_e7c1da1fbecee.jpg"></figure>I created new print profile with this new design and will be develop this project with this size of lamp.If you want use front panels of other designers make sure that is proper size. If it too small just easy enlarge it to 110 % in X and Y axis <figure class="image image_resized" style="width: 44.26%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/2024-03-28_867e2b9fbfc93.png"></figure>&nbsp;02.02.2024 - New front panel added : Deer in the forest05.02.2024 - New front : Birds in love&nbsp;&nbsp;Overview.A Ring Lamp that can be changed to different situations. I designed base with various panels which can adapt to various style and occasion. You can simply change color of it as well as pattern on it, by changing color of diffuser and changing different panels.WARNINGSLed strips can emits some heat depends on what type of led you and voltage you use. In my case temperature of Main Ring achieve 60 °C . Due to this I recommend use filament that can resist that temperature especially for Main Ring. I tested ASA and it works well. Other high temperature filaments should work too (ABS, PETG but I didn&#39;t test it) PLA in this case can bend over time especially if you use heavy panel like budha.So in summary I tested and recommend :Main Ring - ASABase, Diffuser - PLAPanels- PLA or ASAIf you want change panel, always wait to cool down the ring lamp, otherwise PLA cover can bend during take off.Electric parts you need.<ul><li> led stripe - I used: LED COB 8W/1M 12 V, 8mm wide - choose one that can be cut every 2.5 cm</li></ul><figure class="image image_resized" style="width: 430.185px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/6db55f53-37bb-4cbb-ba60-486465aa3c52.webp"></figure><ul><li>dc connector - I used 2.1/5,5 mm , the diameter of the mounting hole is 11.5 mm</li></ul><figure class="image image_resized" style="width: 424.403px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/8867176f-a9e4-4554-8087-7b1fd3a6b430.webp"></figure><ul><li>OFF-ON SWITCH</li></ul><figure class="image image_resized" style="width: 424.332px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/5cf1687e-913a-4186-92f2-75d8d2bac909.png"></figure><figure class="image image_resized" style="width: 425.98px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/4ed0768e-9f72-45b5-9dc0-72aa2a703338.png"></figure><ul><li>Charger 12V</li></ul><figure class="image image_resized image-style-align-center" style="width: 434.759px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/1b0daae1-d790-41b4-a6da-4028c899a774.webp"></figure>Printed PartsMain Ring, Base and Panels can be printed in draft mode 0.28-0.30 mm layer height with no issue.Diffuser should be printed with 0.2 mm layer height.<ol><li>After print, glue led strip to inner side of Main Ring</li></ol><figure class="image image_resized" style="width: 539.361px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/55f0a8a9-5b68-4a7a-b60e-def1c0cf337a.webp"></figure>Start from hole on bottom side<figure class="image image_resized image-style-align-center" style="width: 537.429px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/8f453fdd-01d6-476e-baaa-f03826eac490.webp"></figure>2. Put Main Ring into base. It should fit tight without glue.<figure class="image image_resized image-style-align-center" style="width: 538.864px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/f03a229b-e68e-4835-9d5f-37f66a2677d0.webp"></figure>3. Insert the electric part into the base and connect them by soldering<figure class="image image_resized" style="width: 535.014px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/2e73757c-be70-46f0-8fbb-ebc700b2e62a.webp"></figure><figure class="image image_resized" style="width: 531.08px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/75ca1515-ddbf-47b2-ab0d-34d6c3b795b9.webp"></figure>4. Insert Diffuser to Main Ring”. The Main Ring has a groove into which the Diffuser should be inserted and sit steadily. The flat side to the back.<figure class="image image_resized" style="width: 529.148px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/dd5e9b3f-84e4-47dc-8964-6b93b4f6ee46.webp"></figure><figure class="image image_resized" style="width: 527.23px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/3fc14977-a473-4279-b0d1-25f667c08fba.webp"></figure>5. Insert Panel into Main ring. The Panel has cuts at the bottom to avoid cutting the cables<figure class="image image_resized" style="width: 531.08px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/f414f9b5-fc71-4e83-af57-faf01b92199e.webp"></figure><figure class="image image_resized" style="width: 529.148px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/d3004065-f61c-4175-b595-6235c7b8ead8.webp"></figure>&nbsp;If you any question or suggestion write to me&nbsp;Have fun

Ring Lamp with replaceable panels

Lighting

Marius.M

Smallest version (24x41mm PCB) of the LED clock project by @imeszaros.&nbsp;Led Clock - MICRO (24x41mm PCBs)Smallest version of the <a target="_blank" href="https://www.printables.com/model/189433-wi-fi-connected-led-clock-powered-by-wled" rel="nofollow noopener">LED clock project</a> by @imeszaros. You can print this version even on a A1 Mini :). For more details please check the github fork repository: <a target="_blank" href="https://github.com/mariusmym/LedClock-Resized" rel="nofollow noopener">https://github.com/mariusmym/LedClock-Resized</a><h3>Files uploaded here are for the 24x41mm version.</h3><figure class="image image_resized image-style-align-center" style="width:295.663px;"><img src="https://media.printables.com/media/prints/605334/rich_content/9735b37c-9714-4d56-a1e7-3056258d507c/274021050-a0243b88-147e-4cb1-b519-e2d0f5a27cc9.jpg"></figure>&nbsp;LEDs used for this version are <a target="_blank" href="https://www.lcsc.com/product-detail/Light-Emitting-Diodes-LED_TCWIN-TC2020RGB-3CJH-TX1812ZM_C784563.html" rel="nofollow noopener">TCWIN TX1812ZN</a> (or <a target="_blank" href="https://www.lcsc.com/product-detail/Light-Emitting-Diodes-LED_Worldsemi-WS2812B-2020_C965555.html" rel="nofollow noopener">WS2812B-2020</a> ). I used TCWIN TX1812ZN LEDs in the original design, because they were cheaper at the time. WS2812b-2020 have the same pinout, but be sure you place them in the right way. Keep in mind that the orientation mark from the silkscreen match the orientation mark for TCWIN which indicates the DIN pin, not the GND pin, so just be sure to match the GND pin of the PCB with the one of the LED and you'll be fine. (I did the test and it works. You can even use them with stencil made for TCWIN TX1812ZN footprint). <figure class="image image_resized" style="width:274.388px;"><img src="https://media.printables.com/media/prints/605334/rich_content/230c8dcd-10bb-41d0-a11e-a941adb4b42e/captura-de-ecran-2023-10-11-091326.png"></figure>!!! NOTE: Because of the smaller width of the base for this version you HAVE TO use <a target="_blank" href="https://www.pcbway.com/project/shareproject/LedClock_Controller_Board_ESP32D_E_d23d5dcc.html" rel="nofollow noopener">this version of the controller board</a>.Required PCBs can be found here: <ul><li><a target="_blank" href="https://www.pcbway.com/project/shareproject/[_LedClock_Resized_MICRO_24x41_]_7_Segment_PCB_3d7e49f7.html" rel="nofollow noopener">7Segment PCB</a>;</li><li><a target="_blank" href="https://www.pcbway.com/project/shareproject/[_LedClock_Resized_MICRO_24x41_]_Dots_PCB_4bb0c2ca.html" rel="nofollow noopener">Dots PCB</a>; </li><li><a target="_blank" href="https://www.pcbway.com/project/shareproject/LedClock_Controller_Board_ESP32D_E_d23d5dcc.html" rel="nofollow noopener">Controller Board based on ESP32D/E</a> </li></ul>Print all the parts facing down. No supports required. Covers should be printed with a transparent filament and 100% infill. &nbsp;You can find the .f3z file as well, if you want to tweak the model.

LED Clock - MICRO [ powered by WLED ]

Clocks

philipwaldram

First large design done by 11 year old son and dad! It pushed Tinkercad and my laptop to the limit!Following a youtube video on how to make an articulated dragon, he designed most of the dragon himself, with only a few finishing touches by dad. He would be over the moon if people downloaded his model. We printed it with Silk Rainbow PLA, so no colour changes needed.

Star Dragon

Animals

Pretzel 3D

For those of you that cannot get the motor for this or until you can, i just remixed an additional handle, you will need to print the lower gear from the original model for this to be add to, that will then be used as the top gear to be driven like the bottom gear with a hand crank which i have redesigned from scratch using this helpful bearing design <a target="_blank" href="https://www.printables.com/model/17916-printed-bearing-608-no-balls-no-assembly." rel="nofollow noopener">https://www.printables.com/model/17916-printed-bearing-608-no-balls-no-assembly.</a> This was all done in tinkercad combining free remixable and commerical use design from LazaroCreations to create a neat free solution to drive the marble run.&nbsp;I cannot show the original marble run in any of my images for licence issues, but in terms of installation this is to be fit as the top gear in the marble run to enable it to be manually controlled.

Manual hand crank for Bambu Labs Marble Run

Marble Run

Murata

<figure class="media"><oembed url="https://www.youtube.com/watch?v=jArIfws3gts"></oembed></figure>I designed this toy for my 3 year old to play with so it is intended to be robust enough to survive rough play, and the bucket is slightly oversized for more fun. There’s also an accompanying <a target="_blank" href="https://makerworld.com/en/models/58279" rel="nofollow noopener">dump truck model</a>.&nbsp;Please let me know if any parts break and leave feedback on anything that could be improved upon in the design.&nbsp;The final model is roughly 80 mm wide and everything is assembled with snaps (no glue or fasteners). The only tool required is a coin to tighten the body and tracks together. And there is a hollow pocket for some old AA batteries to add a bit of weight to the body. These are purely optional.&nbsp;Most moving parts are designed with 0.2 mm clearances which work fine on the Bambu X1C but might fuse on other printers. If any joints are frozen or too tight to assemble, try setting <a target="_blank" href="https://wiki.bambulab.com/en/software/bambu-studio/xy-hole-contour-compensation" rel="nofollow noopener">XY Contour Compensation </a>to -0.05 mm. The tracks are offered in two variants, 0.15 mm clearance and 0.2 mm clearance in the raw files. My print came out nicely with 0.15 mm clearance track, but I understand this is not possible on all printers. The tracks show the build-plate side, so they will look a bit nicer if printed on a textured plate.&nbsp;<h3>Build Notes</h3>Be careful to install the H-link build plate face out. It’s a common mistake.&nbsp;When loosening joints for the first time, grab or pry as close to the pivot as possible. If a joint is a little bit stiff, it’s pretty easy to snap a piston by pushing on the end.&nbsp;<h3>History</h3>2024-03-30: Added some extra brim to boom cylinders to help with adhesion.2023-12-04: Minor updates to boom to reduce stuck or broken parts and improve bed adhesion.2023-10-13: Several minor design fixes to make parts more robust. I&#39;ve also included half-length track stls for smaller build plates. You need 4 of these per model. And I&#39;ve included a step file of the assembled excavator so that you can preview different colour pallet ideas. And lastly, there is now a single plate profile that crams the whole thing onto one plate if you&#39;re feeling confident and don&#39;t care about colours.