clement.m333

Procs Design

This is a decorative foldable gift box which you can use to gift small presents, decorate your desk, put under a tiny Christmas tree, store candies, and whatever you can think of. This design features a box base and a lid that fit together. I designed it so that it requires no glue, tape or screws; minimal purge waste to print; different designs to choose from; and two sizes, the smaller one being able to fit on an A1 mini. It uses a single layer thin living plastic hinges and tabs that allow you to fold and snap it together to a sturdy box (as sturdy as a thin layer of plastic that is) and is surprisingly strong! Since it prints flat and folds up, the designs can come from Hueforge and only requires multicolor filament changes at layers which significantly reduces purge waste! This also means that an AMS is not required but is helpful. Unfortunately, the sizes are a bit small as you can only fit so much of a foldable design on the print bed.&nbsp;Sizes (interior volume):<ul><li>Normal (Printable on X1C, P1S, P1P, A1): 7.5cm x 7.5cm x 7.5cm (2.95 in x 2.95 in x 2.95 in)</li><li>Small (Printable on X1C, P1S, P1P, A1, A1mini): 5cm x 5 cm x 5cm (1.96 in x 1.96 in x 1.96 in)</li></ul>&nbsp;Print instructions:<ul><li>Designs are separated by profiles, each pattern has two versions. One for the X1, P1, A1 printers, and one for the A1mini. The A1mini can only fit the small size while the X1, P1, A1 versions have both sizes! Read the description carefully and select the correct design you want. Make also sure to select the correct plates of the size you are interested in.</li><li>If you have an AMS, use only the AMS plates in the profiles! If you don't have an AMS, use the pause swap plates. When using the pause swap plates, it will pause at the color changes. Simply unload and load a new color filament and resume the print. The profile description has a description of the order of colors so make sure to read them.</li><li>All you need to do is decide on a pattern to print, then select my appropriate profile. Afterwards choose what plate you want to print, each plate will have a different part, size, and AMS requirement. Do not increase the number of copies as it will auto rotate the models which may cause the living hinges to fail.</li><li>Tolerances are tight for this model due to the living hinges. Please make sure that your printer can handle a 0.15mm gap. Otherwise it may be a bit difficult to bend the hinges or it may fuse together.</li><li>Make sure that your first layer bed adhesion is good, the living hinges are on the first layer and any first layer defect may affect the bend-ability.</li><li>Check back every now and then, I will be updating this box with more designs as I test and print them!</li></ul>&nbsp;Assembly InstructionsWhen removing your print from the print bed, please be gentle and slow. The living hinges are thin and can be torn off if you aggressively remove the print. If using a textured or hot plate, please wait for the plate to cool completely first before removal. If using a plate with high adhesion where you need to peel or pry it off because bending the plate doesn’t work, consider using a medium for easy release like a glue stick or hair spray. Please see documentation for bigger versions of these pictures.&nbsp;<figure class="image image_resized" style="width:50.36%;"><img src="https://makerworld.bblmw.com/makerworld/draft/531581/2023-12-31_c5d5f24f17c788.png"></figure><figure class="image image_resized" style="width:49.97%;"><img src="https://makerworld.bblmw.com/makerworld/draft/531581/2024-01-15_afe3359d3d038.png"></figure>&nbsp;Designs:Spiral Pattern: Two colors, simple and fast printPrint at 100% infill with a layer height of 0.2mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu White (background, can be any color you want)</li><li>PLA Sunlu Red (Spiral stripes, can be any color you want)</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Snowflake Pattern: Two colors, simple and fast printPrint at 100% infill with a layer height of 0.2mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu White (background, can be any color you want)</li><li>PLA Sunlu Black (Snowflakes, can be any color you want)</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Maze: Two colors, simple and fast printPrint at 100% infill with a layer height of 0.2mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu White (background, can be any color you want)</li><li>PLA Sunlu Blue (Maze walls, can be any color you want)</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Poinsettia Pattern: Three colors, simple and fast printPrint at 100% infill with a layer height of 0.2mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu White</li><li>PLA Sunlu Red (Petals)</li><li>PLA Sunlu Grass green or Green (Leaves)</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Ornaments: 3 colors, hueforge printPrint at 100% infill with a layer height of 0.1mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu Black</li><li>PLA Sunlu Grass Green (Ornament color, any base color should work like red or blue)</li><li>PLA Sunlu White</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Snowy Trees: 4 colors, hueforge printPrint at 100% infill with a layer height of 0.1mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu Black</li><li>PLA Sunlu Grass Green</li><li>PLA Overture Matte Light Blue</li><li>PLA Sunlu White</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Watercolor Snowflake: 4 colors, hueforge printPrint at 100% infill with a layer height of 0.1mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu Black</li><li>PLA Sunlu Blue</li><li>PLA Overture Matte Light Blue</li><li>PLA Sunlu White</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Starry Night: 4 colors, hueforge printPrint at 100% infill with a layer height of 0.1mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu Black</li><li>PLA Sunlu Blue</li><li>PLA Sunlu White</li><li>PLA Overture Matte Yellow</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Blue Marble: 3 colors, hueforge printPrint at 100% infill with a layer height of 0.1mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu Black</li><li>PLA Sunlu Blue (or any base color you want your marble to be)</li><li>PLA Sunlu White</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;&nbsp;Great Wave: 3 colors, hueforge printPrint at 100% infill with a layer height of 0.1mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu Black</li><li>PLA Sunlu Blue</li><li>PLA Sunlu White</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Hearts Pattern: Three colors, simple and fast printPrint at 100% infill with a layer height of 0.2mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu White </li><li>PLA Sunlu Red (lower hearts)</li><li>PLA Sunlu Sakura Pink (upper hearts)</li></ul>&nbsp;Swap Instructions:<ul><li>Start with White </li><li>At layer #5 (1.0mm) swap to Red or Pink (lower hearts)</li><li>At layer #8 (1.6mm) swap to Pink or Red (upper hearts)</li></ul>&nbsp;Basic Box and Basic SLIM Box: The basic box, no design on the walls for easy remixing or customizing.Print at 100% infill with a layer height of 0.2mm with a base layer of 0.2mmAny color you want.Note the model differences:<ul><li>Basic Box has a wall thickness of the base at 2mm as all lids are designed to fit on a box that size.</li><li>Basic SLIM box has a lip of 2mm for the lid and the rest of the walls are 1mm for your remixing or sticker needs, choose that one if you want to add some depth to your box.</li><li>All lids are 1mm thick in this set, as nothing requires them to be thicker.</li><li>Keep in mind how it bends when adding details to the 3d model.</li></ul>&nbsp;&nbsp;Want to slice these files yourself?While I recommend you use the profiles I have prepared and tested, you can slice it yourself if you follow these recommendations:<ul><li>For all projects, make sure to print at 100% infill, it is thin enough that having sparse infill can cause surface defects with a minor reduction in filament used which is not worth it.</li><li>For all projects, the first layer must be 0.2mm thick, the living hinges are designed based on that thickness.</li><li>For any boxes that include Hueforge designs, please print layer height of 0.1mm with a base layer of 0.2mm.</li><li>Do not rotate the files or change the first layer infill pattern, the infill pattern must be 45 degrees to the walls of the model to allow the thin living hinge design to work well.</li><li>I do not recommend scaling the model, it has tight tolerances on the living hinge and Hueforge designs are optimized at a specific scale.</li></ul>&nbsp;Update Log2023/11/23 Release with 4 designs: Spiral pattern, Watercolor snowflake, Ornaments, Snowy trees2023/11/27 Update with 4 new designs: Snowflake pattern, Maze, Poinsettia pattern, Starry Night2023/12/03 Update with 1 new design and opened remixes: Basic Box + SLIM2023/12/31 Update with 2 new designs: Great Wave and Blue Marble2024/2/11 Update with 1 new design: Hearts Pattern

Foldable Gift Box Decorative

boxes

TheBear

So, you want to personalize your A1 Mini a bit, do you? Well, you've certainly come to the right place! Presenting the A1 Mini Extruder Icons!They spin with the extruder gear, just like the original icon! In the following days/weeks, I will be uploading a lot of different Icons, which can be mounted to the A1 Mini Extruder. And I've decided to the go with “external” Icons, as that provides a lot more space for being creative with the models. It also just looks kinda cool, that they are just sticking out from the printer like that, don't you think? Installation Guide & ExplanationBelow, you'll find a guide on how to install the icon. And don't worry about removing the Window from the Front Cover. It is a non-permanent modification. You can always put the window back in. (Bambu Lab has even uploaded their own Icon model to MakerWorld which requires window removal. So, removing the window is not damaging to the printer)&nbsp;First InstallationThe first installation takes the longest (although still quite straightforward and simple) - all subsequent installations are significantly easier and faster!<ol><li>Remove front cover</li><li>Remove the original extruder icon by pulling it away, straight, from the tool head</li><li>Remove window by pressing on it from the outside (Tip: You can attempt to simultaneously press on the inside clips (marked wiith red on the picture for this model) to make the window pop out a bit more easily)</li><li>Reinstall the front cover</li><li>Press your new icon through the whole, where the window used to be, and onto the metal rod, where the original icon was located. It should be a snug fit to ensure it stays in place.</li></ol>It really is simple, once you try it out yourself. Subsequent Installations/Switching Between Icons Once you have done the first installation, switching to a different one of my Icons is extremely simple. You don't need to remove the front panel or anything. Simply pull the current icon off the printer, and press on another one. Simple as that! 5-10 seconds, top! On my profile, you will find many more Icons and a Display/Holder for them - in case you decide to print multiple and need a way of storing them! (Bonus! Depending on your printer's tolerances, the Display/Holder has a loose enough fit to make the icons spin around freely. It is quite the fidget toy! Try printing the holder for just 1 icon and have it by you at your desk. It can become quite addicting to spin the little icon around!) The Icons themselves were created using Make My Sign in Maker Lab. (Powered by Make My Sign from MakerWorld(makerworld.com/makerlab/MakeMySign)

A1/A1 Mini Extruder Icon - Plague

printer decoration

Adam L

Note to printables staff : this is NOT a remix of a different model that doesn’t allow remixes, it is an original design of my own making where I invested significant effort. As proof, I am including the Fusion360 CAD files here to prove my design is original from scratch and not a “remix” of that model. It is only a remix of my OWN model. I do respect licenses of others. Note to everyone else: Now includes Fusion360 Model (because reasons.. ) !&nbsp;Some people suggested that they would prefer to use a toothbrush or brass bristle brush to clean their threads instead of the parent <a href="https://www.printables.com/model/476890-super-screw-scrubber-a-sensational-solution-for-sp/remixes" rel="nofollow">Super Screw Scrubber </a>design with paper towel. For them, I've designed this alternative version of the scrubber that lets you slap on a cut-off toothbrush or brass bristle brush or similar and glue it onto the guide. This simple but effective modification lets you get a deeper clean with a longer reach!This version is the more reliable tapered version from the parent that should reduce any first layer print issues. Since the brush bristles are the key to cleaning in this version, the exact tightness of the threads is less important.<h4>Versions</h4><ul><li>DefaultSize (Recommended)</li><li>ShortBrush - if you have a brush that's not quite long enough to comfortably reach, this offers a closer spacing of the flat part to the lead screw by ~ 4 mm. </li></ul>&nbsp;<h3>Print Instructions (same as parent)</h3><ul><li>Print at high layer resolution, I recommend 0.1 or 0.08 if possible on your printer, so that the threads fit nicely. There are slight tolerances built into the thread design so that it should clamp nicely.</li><li>Most filaments should be fine.. but I would avoid anything like carbon fiber or glow in the dark filament to avoid any scratching of the screws (though most are made of steel that probably would not scratch anyways).</li><li>Orient the flat side down. I designed the part slightly asymmetrically so this is intentionally hard to screw up when placing on your bed :).</li></ul><h3>Use instructions </h3><ul><li>Find an old toothbrush or brass bristle brush, cut off the head. Use hot glue (recommended) or some other suitable glue to attach the head to the flat section as shown in the pictures.</li><li>Attach the clamp and brush to your lead screws as shown.. run the bed up and down (make the screws rotate), and hold the clamp in place as you do so.</li><li>Remove the widget, and clean the gunk off (can just rinse with IPA and/or acetone for most greases).</li><li>Re-grease your threads if you stripped all the grease off.</li></ul>&nbsp;<ul><li>Don't use as a regular toothbrush anymore, the ADA has informed me this is not an approved dental product after this modification :). <img src="https://media.printables.com/media/prints/477870/rich_content/50fb1bab-9bd4-4c1c-b9c8-59d26d9d371c/image.png#%7B%22uuid%22%3A%222da5821e-19c2-4860-832f-116d5b83b985%22%2C%22w%22%3A652%2C%22h%22%3A600%7D"></li></ul>&nbsp;3MF & STEP file included!

Super Screw Scrubber: A Sensational Solution for Sparkling Screws (Brushy Edition)

printer tools

DutchWorkX3D

check my FB page https://www.facebook.com/groups/bambu3d4all There is a lot of info and help there ;-)&nbsp;I designed v3 from scratch based on the v2 version.It now has more strength and more place for honeycomb / hex add-ons.I have added:<ul><li>Honeycomb / Hex Ledstrip holder</li><li>Honeycomb / Hex Build plate holder</li><li>Honeycomb / Hex Top glass holder</li></ul><img src="https://makerworld.bblmw.com/makerworld/draft/176841/2023-09-27_0064ddb96eb55.gif">I have added the 3mf file with the settings, of course you can adjust to your own settings.I get a lot of requests and I don't mind following up on them as it makes these projects more interesting, although it takes a lot of time I really don't mind spending my time but I would appreciate it if you join the club as club members can be assured I follow up on their requests.If you like you can join my Bambu3D4All FB page https://www.facebook.com/groups/bambu3d4all/

X3D-v3 Riser | Bambu Lab X1/P1 AMS Stand

ShakaStudio

This is part of a Set: <img src="https://makerworld.bblmw.com/makerworld/draft/94352/2023-10-11_e110fb66a08e.jpg">&nbsp;Frame 01 - <a target="_blank" href="https://makerworld.com/en/models/39255#profileId-38273" rel="nofollow noopener">https://makerworld.com/en/models/39255#profileId-38273</a> Frame 02 - <a target="_blank" href="https://makerworld.com/en/models/40788#profileId-40725" rel="nofollow noopener">https://makerworld.com/en/models/40788#profileId-40725</a> Frame 03 - <a target="_blank" href="https://makerworld.com/en/models/42101#profileId-42689" rel="nofollow noopener">https://makerworld.com/en/models/42101#profileId-42689</a>&nbsp;This model has been carefully designed to look great with 4 colors. This is an easy to print 4 color Filament painting to add to your other Halloween décor.Only filament swaps! No AMS necessary.&nbsp;This does not need an AMS to print, but it does make it easier. If you have an AMS, print directly from the provided print profile.If you don't have an AMS, open and slice in the Bambu Studio app and add pauses at the provided layer heights for filament swaps.&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.24mm&nbsp;Swap Instructions: Start with Black At layer #8 (0.8mm) swap to Night Gray / Dark Gray At layer #10 (0.96mm) swap to Matte Grey / Light Gray At layer #14 (1.28mm) swap to White for the rest.

Halloween Day of the Dead 02 - 4 Color Hueforge Filament Painting

hue forge

Jal Shah

To continue on the previously designed tetrahedron lamp, I designed dodecahedron lamp. I also found tetrahedron lamp to be a bit on a smaller side, so this time I wanted something larger. This lamp is 360mm (≈ 14 inches) tall and 320mm (≈ 12.6 inches) wide and deep.You can use LEDs with this lamp and there is a special frame designed for LED wiring. You can also use E26 \ E27 standard pendant light with this lamp and there is a special insert for that. You also get a stand if you decide to put the lamp on some surface or you can hang the lamp with pendant light.You will also find two types of films this time. One is simple and plane, but the other has numbering on it to make the D12 dice lamp for your gaming room.<h3>Printing</h3>Depending on the version you choose to print, you can refer to the guide below for the number of pieces that need to be printed.<h5>LED Version</h5><ul><li>11 Frame Pieces</li><li>1 Frame with Hole for LED Strip Wire</li><li>12 Insert Pattern Pieces</li><li>12 Insert Films (Pattern 1 or Pattern 2)</li><li>30 Alignment Keys</li></ul><h5>Pendant Light Version</h5><ul><li>12 Frame Pieces</li><li>11 Insert Pattern Pieces</li><li>1 Insert Pattern - For E26_E27 Pendant Lamp</li><li>11 Insert Films (Pattern 1 or Pattern 2)</li><li>1 Insert Film - For E26_E27 Pendant Lamp (Pattern 1 or Pattern 2)</li><li>30 Alignment Keys</li></ul><h5>Stand</h5><ul><li>1 Stand Top</li><li>1 Legs Connector</li><li>5 Legs</li></ul><h3>Assembly</h3><ul><li>Glue \ Press fit inserts into frames.</li><li>I used Vellum paper as the inside backing to diffuse the light. You can print and use either of the inserts for light diffusion as well.</li><li>Stick printed inserts or vellum paper to the inside of the frames.</li><li>Glue all frames together using alignment keys and keeping the bottom side open.</li><li>Finish led work or pendant lamp before inserting the bottom insert. I used pendant light wiring kit myself.</li><li>Lastly attach the bottom panel. I used tacky craft glue to attach the bottom panel to be able to take it off if I need to change the bulb.</li></ul>

boxes

printer decoration

printer tools

ams

hue forge

lampe