ciril51

mcgybeer

Cali-Dragon!Is your printer able to produce quality prints? When printing organic models you don't really care about precision and tolerances, you want them to look pretty. This small print allows you to test:<ul><li>Surface smoothness (aka layer consistency)</li><li>Stringing</li><li>Small perimeters</li><li>Overhangs</li><li>Ghosting</li><li>Details</li><li>Multicolor</li></ul>If printed in multiple colors, I encourage you to print several at the same time. Build a Cali-Dragon army!

Cali-Dragon

calibration 

cyanidesugar

A wibbly wobbly timey wimey model for all the Whovians out here! &nbsp;This is another Hueforge Hybrid print, where the Tardis ‘pops out’ of the print for a little personality. This print combines Hueforge filament painting methods with traditional 3D printing to create a lovely pop art style print. &nbsp;Note: If you are using the 3MF for one click printing, all settings will have been applied to the model. I used 5 filaments for this on one AMS and swapped one spool out of the AMS when the colour was finished printing for the 5th colour. &nbsp;Note 2: This print also has steep overhangs with no supports. If you're not confident in your printer handling supports with my 3MF file settings, do not use the one-click printing function and import the 3MF file into your slicer and adjust the settings for the ‘Tardis_Export3.STL’ part of the assembly to suit your own supports/overhang settings. &nbsp;If you are not using the one-click 3MF, the print instructions and recommendations are as follows:<ol><li>This printed without supports, but I enabled slow down for overhangs. This print DOES require your printer / filament to be dialled in to be able to print the overhangs for the Tardis effectively. If you're not confident, I would enable supports. You would not be able to see it or remove it as the supports should only be applied to areas inside the Tardis. </li><li>I used a layer height modifier to modify the layer height specific to the Tardis (2.04mm - 33mm) to increase it to 0.16 to speed up the print.</li><li>I also modified the infill for the the Tardis and the ‘Generic Cube’ to only print at 10% with 4 walls and 4 top and bottom surfaces. </li><li>Since this print re-uses the Blue and the Black, if you are using only 1 AMS, I suggest swapping out Slot 3 (should be orange) for the white when you are swapping the colours out. </li><li>My recommendation is to have Black, Blue, Orange, Yellow in Slots 1,2,3, and 4 in the AMS, and then swap the orange for white when the orange is done printing. </li><li>If you want to use a different colour for the Tardis, then you can swap out the Blue accordingly</li></ol>Filament Instructions&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.2mm&nbsp;Filaments Used: - PLA Kingroon Black Transmission Distance: 0.4 - PLA+ Polymaker Starlight Neptune (Blue) Transmission Distance: 1.8 - PLA CC3D Orange Transmission Distance: 7.4 - PLA CC3D Lemon Yellow Transmission Distance: 8 - PLA Kingroon White Transmission Distance: 8&nbsp;Swap Instructions: - Start with Black - At layer #8 (0.76mm) swap to Starlight Neptune (Blue) - At layer #9 (0.84mm) swap to Orange - At layer #15 (1.32mm) swap to Lemon Yellow - At layer #17 (1.48mm) swap to White- At layer #24 (2.04mm) swap to Black- At layer #27 (2.52mm) swap to Starlight Neptune (for the Tardis!)&nbsp;The Tardis model can be found <a target="_blank" href="https://www.thingiverse.com/thing:367130" rel="nofollow noopener">here</a> by <a target="_blank" href="https://www.thingiverse.com/23Maple" rel="nofollow noopener">23Maple</a>.

Tardis in Space

geek 

wikiwada

A Voronoi cat model is an elegant and modern representation of a feline figure, created using a unique geometric partitioning. The sculpture is a three-dimensional structure that is characterized by the Voronoi diagram pattern, where the surface is divided into distinct, irregularly-shaped cells that are tessellated to form a cohesive whole. Each cell in the Voronoi pattern appears as a polygon, with varying sizes and shapes, giving the impression of a natural, organic form, as if the cat has emerged from a frothy sea of mathematical precision. The cells are interconnected, creating a network of edges that defines the shape of the cat, from its pointed ears and curved back to its swishing tail and poised paws.

Voronoi Cat

Deco

Julian Hof

Hello This is a clip for the sun visor in the car. You can easily attach sunglasses or glasses to it. You can also clip money or a photo on the inside. This means you never have to look for your glasses again because they are always hanging there.The clip is simply clipped on without glue or anything else.You only need 12g of filament for this clip.

Brillenhalter für das Auto, Sonnenblende / Glases holder for the car, sun visor.

tools

DerTobi01

V2 is for mounting on the back. Mounting the LED bar on the front can lead to problems with the Z-axis.Assembly is at your own risk.&nbsp;Update from December 31, 2023:I revised the design again to create more space between the print head and the clamp.&nbsp;I tested this in advance. There were no problems for me. But please also test it for freedom of movement.&nbsp;You can simply exchange the revised brackets for the old ones.&nbsp;

calibration

geek

Deco

tools

A1 accessoires