chuanxuelingfeng

LoboCNC

This simple disc launcher prints quickly and easily in a fun kit card format. Just snap a disc into place and the launch it by pushing it forward through the gap in the fork. It flies surprisingly far! I've also included a plate with the separate parts if you want to print them separately, or for when you (inevitably) lose the discs.&nbsp;Assembly The launcher consists of just 3 parts: the springy launching fork, the two-fingered grip, and the thumb pusher. To assemble, first put the pusher piece over the grip as shown in the 2nd photo. Then tilt the fork into the rear hook as shown in the 3rd photo. Finally, just snap the fork flat, locked into place by the front hook as shown in the 4th photo.&nbsp;To load the disc, pull the plunger all the way back with your thumb, and then tilt the leading edge of the disc into the front inside edge of the fork as shown in the 5th photo. Then push it flat against the backstop on the plunger as shown in the last photo. Now you're ready to launch!&nbsp;Credit: There are a bunch of similar disc launchers, but the earliest design I could find of this type was from <a target="_blank" href="https://www.thingiverse.com/thing:578799/files" rel="nofollow noopener">davedelay on Thingiverse</a>. Let me know if you know of an earlier version.

Flying Saucer Launcher

2024

noongom

I took legs from <a target="_blank" href="https://makerworld.com/models/42396" rel="nofollow noopener">Jack O Lantern Octopus remix</a> and added my modeling as its head.<img src="https://makerworld.bblmw.com/makerworld/draft/251541/2023-12-10_db02baa65a896.png">Painted eyes with acrylic color.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/251541/2023-12-10_87ed7001c2085.jpg"></figure>

Mars People head octopus.

好的

laisch

This is a scaled flyable micro version of the ASW20 sailplane from Schleicher. The model was created to be lightweight and printable in normal PLA.Because of it's lightweight behaviour it's a little bit fiddly to get it together properly but it's still strong enouth to survive crashes. So please read the Instructions before you build it.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_7930ef971b4078.gif"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_b32700811d73d.gif"></figure>&nbsp;<h3>Printing:</h3>Make sure you align the STL-Files flat with the build plate like in the pictures.&nbsp;The Fuselage and the Nose have to be printed in Vase Mode (0.12mm) for best quality and perfect stability. Make sure you geht your part cooling right otherwise the thin tail section won't print properly because of overheating. Turn Bottom Layers to 1 Layer.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_2xua1hjiurid.jpg"></figure>The Wing parts are printed in normal Mode with 0.12mm Layerheight. Make sure that the first layer prints in 0.2mm.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_9yaljcx3l44z.jpg"></figure>After printing carefully remove the wings from your print bed and make sure not to overbend them.&nbsp;<h3>Assembly</h3>Clean up the parts from any print defects<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_mmrpjuqrlmyo.jpg"></figure>&nbsp;Testfit if the wings fit inside the fuselage. The reinforcement part of the wing should touch the fuselage. If not, just cut away the parts wich are too big.<figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_k461jxekhpvj.jpg"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_p3zauy5szoj1.jpg"></figure></td></tr><tr><td>Wing not aligned with fuselage</td><td>Wing aligned with fuselage</td></tr></tbody></table></figure>&nbsp;When the testfit is ok, put some superglue onto the wings and glue them in place.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_v2l13jrwi32n.jpg"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_4dvxkmto8krd.jpg"></figure>&nbsp;Make a testfit if the rudder fits in to the elevator. If not you can take a cutter knife to clean it up a little bit.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_hiskzgmshhkj.jpg"></figure>&nbsp;After that put the rudder and elevator together and secure them with some CA glue. Try to not use too much glue because of extra weight.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_c5669idp5zad.jpg"></figure>&nbsp;Glueing the rudder/elevator assembly to the fuselage is the hardest part of the build. It works the best if you put one small drop onto the fuselage and temporary secure it. After that you can check the alignement and adjust it properly.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_sklgvblwtn24.jpg"></figure>If it looks fine, just secure the whole thing with more superglue.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_58pkfcwdk5pu.jpg"></figure>&nbsp;To make the whole thing fly you have to add weight to the nose and adjust the center of gravity. For me a 4,5mm steelball did the trick. You can temporary secure the nose to the rest of the plane with some tape and check it's flight properties.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_9hxutt2kk35r.jpg"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_ui9nlrtydip2.jpg"></figure>&nbsp;For checking the center of gravity you can balance it on two screws. The COG should be at ⅓ of the wing measured from the front.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_vbnmudk1iyhh.jpg"></figure>if it does'nt fly properly you can also try to give it a little bit of lift by bending the elevator up.&nbsp;If it flys, you now can finally glue the nose to the rest of the sailplane.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_jasr1r5920mo.jpg"></figure>Have Fun!&nbsp;&nbsp;<figure class="table" style="width:92.21%;"><table class="ck-table-resized"><colgroup><col><col><col></colgroup><thead><tr><th colspan="3">If you like this model you may have a look at my other flying toys too</th></tr></thead><tbody><tr><td><figure class="image"><a href="https://makerworld.com/en/models/81500" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-12-03_bc748d83c35e18.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/81500" rel="nofollow noopener">Geared Propeller Launcher</a></td><td><figure class="image"><a href="https://makerworld.com/en/models/76104" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-12-03_eadf473572ad4.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/76104" rel="nofollow noopener">Flying Bat</a></td><td><figure class="image"><a href="https://makerworld.com/en/models/21091" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-12-03_a8fc21a53267c8.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/21091" rel="nofollow noopener">Cross Bow</a></td></tr></tbody></table></figure>

ASW20 Sailplane (micro glider - flyable)

plane

uhltimate

Introducing the DIY Fly Swatter Gun, the ultimate weapon in your battle against mosquitoes. This 3D print model lets you build your own mosquito-swatting machine. Just snap the pieces together, no tools required! With a reach of 30cm, you'll have the upper hand in the mosquito-hunting game.&nbsp;IMPORTANT: "min. 4 Wall loops" if the spring has infill pattern, it will not work&nbsp;<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=Mk_qMPQVysw"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/Mk_qMPQVysw" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

2024

好的

plane

模型