chiefpilot

remi.rafael

<div><h1>Summary</h1><div>This collection regroups the models of handles for nuts and screws i designed over time. All designs can be printed without support, refer to the illustration to identify the different types.Edit: Bigger sizes are now available here: <a href="https://www.printables.com/model/455708-handles-for-m7-to-m12-bolts-and-screws" rel="nofollow">https://www.printables.com/model/455708-handles-for-m7-to-m12-bolts-and-screws</a> or here: <a href="/thing:5975322" rel="nofollow">https://www.thingiverse.com/thing:5975322</a></div></div>

Handles for M3 to M6 bolts and screws

utilities

VanillaWafer

NO SUPPORTS &amp; PRINTS EACH UNIT FULLY ASSEMBLED!THESE ARE MEANT TO SERVE AS AN EXTENSION TO MY LINKEDBIN PROJECT.DRAWERS MUST BE THE SAME LENGTH TO MAINTAIN COMPATIBILITY. UPDATED NOW WITH ADD IN DRAWER DIVIDERS (SEE PRINT PROFILES) Finally a good simple print in place solution to some desktop drawers. drawers are large enough to fit pretty much all of your 3d printing tools like flush cutters/ deburring tools/ scrapers/ etc.&nbsp;If you are like me then you have drawers but throwing these tiny tools into these massive drawers leads to losing everything, this is my solution to my own headaches and hopefully yours also. These desktop drawers are meant to have a small enough footprint to not impede your space but be large enough to be useful. These use a low material cost dovetail joint to form a user friendly stackable masterpiece of your own creation right on your desk or workshop. IF YOU PRINTED THE ORIGINAL LINKEDBIN AND WANT TO ADD ONTO THEM WITH THESE.the original LinkedBin was the 196MM version, the model version in this file has been updated to allow for more reliability when printing and it will still work with the older version. TO LOCK TOGETHERSimply just push the stubs that are toward the front of your drawer into the slots then push forward while lining up the stubs in on the back end<img src="https://makerworld.bblmw.com/makerworld/draft/845096/2024-03-28_02856b677ad75.png"><img src="https://makerworld.bblmw.com/makerworld/draft/845096/2024-03-28_7b9cb16c36753.png"><img src="https://makerworld.bblmw.com/makerworld/draft/845096/2024-03-28_0803b2b5bbc0b.png"><img src="https://makerworld.bblmw.com/makerworld/draft/845096/2024-04-07_b169ce04b669a.png"><img src="https://makerworld.bblmw.com/makerworld/draft/845096/2024-04-07_ad5892a14fe61.png"><img src="https://makerworld.bblmw.com/makerworld/draft/845096/2024-04-14_14032fd759a8e.png">

LinkedBin Project - PIP Modular Drawers For All

zach

JDJDJD

<h2>Meet The Shifty!</h2>&nbsp;The Shifty allows you to quickly and easily center your build plate on Bambu Lab 3D Printers (X1C/P1S/P1P Style).&nbsp;This is the first and original Build Plate Guide ever to be shared on MakerWorld.&nbsp;As a brand new product, I&#39;ve meticulously designed the Shifty to make your life easier, every time you insert your build plate.&nbsp;<h3>How it works:</h3>&nbsp;The Shifty build plate guide increases the contact area of the built-in plate guides. This means you have more room for error when sliding your plate into place.&nbsp;It also eliminates cases where the plate skips over the existing guides, or lands on top of them uncentered and un-level which can cause failed prints.&nbsp;The increased guide height also allows you to slide the plate in at a greater angle, which is more comfortable and minimizes instances when the plate clamps down before it&#39;s properly positioned.&nbsp;<h3>How to use:</h3>&nbsp;Slide your plate in like normal, but aim the back left corner of your plate towards the Shifty. Once you make contact it will take over and shift your plate perfectly into place.&nbsp;The Shifty is low profile and clips to the back left corner of your bed, out of the way from activity.&nbsp;<h3>Installation:</h3>&nbsp;Step 1 - Connect The Front:&nbsp;Insert the front tab into the notch located at the front of the built-in guides.&nbsp;Step 2 - First Click:&nbsp;Wrap it around towards the back and press so it “clicks” into place. (see video below).&nbsp;Step 3 - Second Click ←- Double Check This One:&nbsp;After you hear the first click as shown in the video, you may have to press down on rear hook (right side of back edge) to seat it properly into place. This is the second click. I recommend pressing down in the back even if you think you have it in place just to make sure.&nbsp;When properly installed, the Shifty will be very snug, perfectly level, and without distortion.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000083480/design/2023-12-04_8cba772444acc.gif"></figure>&nbsp;&nbsp;If you have any questions, feel free to direct message me.&nbsp;&nbsp;<h3>Tips and Notes:</h3><ul><li>The Shifty is designed to look cool and print beautifully. The supports are custom tailored and break away easily in one piece with a simple twist for most materials. For some materials, you can simply twist counterclockwise while it&#39;s still on the plate and it will cleanly break away.</li><li>To replace or remove, access it from the bottom side of the bed and press backwards on the back edge until it unclips.</li><li>When properly installed, the Shifty will be very snug and perfectly level. If it isn’t, study it&#39;s shape and check the back edge, you may need to push it down on the back edge so it snaps into place.</li><li>If you print a lot of high-temp materials, consider making a Shifty in PETG, ASA or ABS. These profiles are tested and also available.</li><li>At this time I&#39;m releasing the left side only. I have a right side model completed, but am not releasing it for now since the left-only approach works well and keeps the Shifty away from the back right purge strip activity. Feel free to mirror a right side in Bambu Studio for your own use, but please don&#39;t upload profiles with the right side mirrored at this time.</li></ul>

The Shifty - Build Plate Guide

Mods

wuguigui

Updated20231109Someone suggested designing a new one for the baby, so I made a new one, just scale the length, and now you have a cute version of “Foldable Hanger -print all at once”.<img src="https://makerworld.bblmw.com/makerworld/draft/706607/2023-11-09_e8f52fd9f9808.png"> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~&nbsp;Updated20230808The new version 2.0 is coming! wider ends, stronger joints, and hook, several details improvements...There are 2 files, "Foldable Hanger2.0_Tight" is for printers that can achieve high printing speed and high precision(like Bambu lab P1P or X1C, which takes 2 hours to print this hanger with high quality), and "Foldable Hanger2.0_Loose" is for other printers, if you have trouble like stick together when printing the previous file.I suggest using a putty knife to separate the parts, as shown in the image.Thank you again for your "Like", follow me and keep on supporting me! Salute to Makers! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~<h2>Summary</h2>It's a Foldable Hanger that can be printed all at once and with no support.Specially designed for travel, very compact and reliable. There are 2 versions, the tight one for high-precision printers and a normal one for others.watch the video for more information: <a target="_blank" href="https://youtu.be/QII3ODl7uRc" rel="nofollow noopener">https://youtu.be/QII3ODl7uRc</a>Click"like" for me if you really like it, it will encourage me to design more new things.See my other designs at: <a target="_blank" href="https://makerworld.com/en/u/2112721175" rel="nofollow noopener">https://makerworld.com/en/u/2112721175</a>Thank you!<h2>Post-Printing</h2><figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=QII3ODl7uRc"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/QII3ODl7uRc" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

utilities

zach

Mods

To print