chichocom

Litolunar

I created a frame specially designed for square photographs of size 150x150 mm. It is in two parts so that the two pieces fit together.

Frame hueforge (150x150)

hueforge

Libb_s

Cable organizer

cables

Shaztech.info

8 Trays HDD Box for NAS/ServerFully printed enclosure (you can print the external case or make your own in wood/metal/aluminium)Using long SATA/SAS cables, so no complicated electronicsAll parts are easily available on Amazon/Aliexpress/EbayTrays are available for 3.5 and 2.5in HDD/SSD&nbsp;Connect the fan to the 12V wire (Yellow)Connect the LED with the resistor to the 5V wire (Red)&nbsp;Overall dimensions: 268mm (10.55 in) wide, 214mm (8.43 in) depth, 152mm (6 in) Height&nbsp;Bill of Materials:42x - Torx Screws #4 x 1/2&#34; - McMaster #99512A219 8x - Socked Head Screws M3 x 22mm - McMaster #91290A124 1x - Computer Fan 120mm (with 4 screws) 1x - 5mm LED + resistor 2x - Quad SATA 1 Meter Cable (or SAS if you have a card) (see pictures) 8x - SATA Adapters Male to Female Straight (see pictures) 8x - SATA Power connector (Puncture type without soldering, can be salvaged from old cables) (see pictures) Some 16 gauge wires to create your power cable (2x Female molex to one end)&nbsp;If you want smaller check my 4 Trays box.(12 Trays 3U rack mountable coming soon….)&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/shaztech_info" rel="nofollow noopener">Buy me a coffee</a>

8 Trays HDD Enclosure (SATA/SAS)

servers

This is a Holder for drying reusable silica gel in a Sunlu S2 Filament Dryer. It is designed for  reusable Silica Gel with diameter 2mm-4mm, for example this:<a target="_blank" href="https://www.chemdiscount.de/chemikalien-von-a-bis-z/silica-gel/silica-gel-lose/silica-gel-lose-orange-mit-farbindikator/1kg-silica-gel-mit-orangem-indikator.html" rel="nofollow noopener">https://www.chemdiscount.de/chemikalien-von-a-bis-z/silica-gel/silica-gel-lose/silica-gel-lose-orange-mit-farbindikator/1kg-silica-gel-mit-orangem-indikator.html</a> Print 2 Plates, 1 lid and 1 tub. Assembly:Both plates are printed with 3 assembly sticks, which fit into the 3 holes on each side of the tub. Take the first plate press the 3 assembly sticks into the 3 tub holes, to combine the pieces. Repeat on the other side. For better stability and fit apply some glue to the contact area of plate and tub.You also have to glue 4x2mm magnets in to the holes of the lid and the tub.There is also a spout for safer handling of the silica gel:<a target="_blank" href="https://www.printables.com/de/model/746162-spout-for-silica-gel-holder-sunlu-s2" rel="nofollow noopener">https://www.printables.com/de/model/746162-spout-for-silica-gel-holder-sunlu-s2</a>There is also a Funnel for safer handling of the silica gel:<a target="_blank" href="https://www.printables.com/de/model/749478-funnel-for-silica-gel-holder-sunlu-s2" rel="nofollow noopener">https://www.printables.com/de/model/749478-funnel-for-silica-gel-holder-sunlu-s2</a>There is also a Silica Gel holder with wallholder for your dry box:<a target="_blank" href="https://www.printables.com/de/model/777510-silica-gel-holder-for-dry-boxes-with-wallholder" rel="nofollow noopener">https://www.printables.com/de/model/777510-silica-gel-holder-for-dry-boxes-with-wallholder</a>&nbsp;Version 2 released 02.2024:Changed the alignment sticks to shorter alignment nubs. The alignment sticks tend to break too easy while assembly. Shorter alignment nubs should prevent breaking.ASA Version added:I added a Version for ASA or ABS.  When the holder is very full, the PETG Version deformed over time. So I added a ASA Version which works better on higher temperatures. This version is without allignment pins. But it also holds very good with super glue. The standard lid works with the ASA Version.&nbsp;Print Option:Bambu Lab PETG / ASA15% Infill&nbsp;If you have any questions, feel free to ask.

Silica Gel Desiccant Holder Sunlu S2

sunlu

alex3000

Im Dacia Jogger wurde der Handgriff von der Kofferraumabdeckung nicht ausgeschnitten.Damit das nach dem ausschneiden nicht ausgefranst aussieht, habe ich hier ein Griff designed.&nbsp;Gedruckt habe ich ihn in ABS.&nbsp;________________________________________In the Dacia Jogger, the handle of the trunk cover was not cut out.So that it doesn&#39;t look frayed after cutting it out, I designed a handle here.&nbsp;I printed it in ABS.

Dacia Jogger Handgriff Rollo handle

dacia

d.horak93

The assembly procedure is in the photos.Print the lampshade using the print profile that I created specifically for the lampshade.&nbsp;Other shade:  V1 <a target="_blank" href="https://makerworld.com/en/models/209164#profileId-229082" rel="nofollow noopener">https://makerworld.com/en/models/209164#profileId-229082</a>V2 <a target="_blank" href="https://makerworld.com/en/models/209165#profileId-229083" rel="nofollow noopener">https://makerworld.com/en/models/209165#profileId-229083</a>V3 <a target="_blank" href="https://makerworld.com/en/models/247143#profileId-263472" rel="nofollow noopener">https://makerworld.com/en/models/247143#profileId-263472</a>V4 <a target="_blank" href="https://makerworld.com/en/models/381596#profileId-281809" rel="nofollow noopener">https://makerworld.com/en/models/381596#profileId-281809</a>&nbsp;Other lamp:<a target="_blank" href="https://makerworld.com/en/models/442346#profileId-348261" rel="nofollow noopener">https://makerworld.com/en/models/442346#profileId-348261</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000185319/design/2024-03-20_a447046955482.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000185319/design/2024-03-20_eb52cbc4c0bd3.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000185319/design/2024-03-20_1f625bd5d9d1e.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000185319/design/2024-03-20_6f77a9b0e5795.jpg"></figure>&nbsp;

Wave lamp

lamparas

user_3257010834