cagneycarnation

LoboCNC

This original design puzzle box, with hidden latches, sliding panels, a mystery dial, and covered with runic symbology, is the perfect place to keep your most valuable keepsakes safe (from anyone without a hammer). It requires just the right sequence of dial and panel motions to open it. Or to fully close it. It's actually not that diabolical, making it great for kids.Printing I printed this in Pearl Mouse PLA with Black for the accent colors. No supports are required for any of the parts. Use exactly 0.2mm layers to make the build-in removable supports print correctly. I would also recommend using a 0.4mm or smaller nozzle. Print 2 of each latch piece and on of everything else. To get the accent colors, print the first layer of both sides and the dial in your accent color, and then change the filament to print the rest in the main color. For the lid, print the first 38 layers (up to 7.6mm) in the main color and then print the rest of the layers in your accent color.Assembly First note that the main box part has 2 built-in break-away supports on either side in the upper slots. One is highlighted in blue on the photo below. Theses should just pull out cleanly.<img src="https://media.printables.com/media/prints/596099/rich_content/37c006d1-2c90-4a65-a46f-0495be52176f/pb-support.jpg#%7B%22uuid%22%3A%22ccd09f53-8be0-408c-a9da-c8371aa06c05%22%2C%22w%22%3A666%2C%22h%22%3A500%7D">The Latch pieces each need a small length of filament to act as a pins that fit into the dial. The holes in the ends of the latches are a tight fit on 1.75mm filament, so start off cutting about a 15mm length and cut a taper on one end. Jam the tapered end into the hole first and then tap in partway through. cut the tapered end off flush with the one side of the latch and the other end should protrude by 2.5mm as shown in the photo below:<img src="https://media.printables.com/media/prints/596099/rich_content/934bff51-4708-49f3-8831-e8f0287a1db3/pb1.jpg#%7B%22uuid%22%3A%2248744a69-6040-4913-97b3-60fb04579ca3%22%2C%22w%22%3A771%2C%22h%22%3A578%7D">Insert the 4 latches into the hole in the cover with the pins facing up as shown:<img src="https://media.printables.com/media/prints/596099/rich_content/edcefc84-ed79-4506-a2ed-7b5f5f8235cf/pb2.jpg#%7B%22uuid%22%3A%225ca076ac-f373-4997-8521-e16bebcdf82c%22%2C%22w%22%3A2000%2C%22h%22%3A1500%7D">Flip the whole thing over and place the dial in the center hole. Slide the latches in or out so that all 4 fit into the groove in the bottom side of the dial:<img src="https://media.printables.com/media/prints/596099/rich_content/634f76f5-f1f3-4fe8-a71c-ba8804934210/pb3.jpg#%7B%22uuid%22%3A%2277ecd082-b71b-4b12-849e-fb362c3ae156%22%2C%22w%22%3A2000%2C%22h%22%3A1500%7D">Now press the dial bottom onto the underside of the dial and press click it onto place.One of the two side pieces had just one hole on this inside. Slide it onto the grooves on the end that allows it to drop down about ½" from flush with the top:<img src="https://media.printables.com/media/prints/596099/rich_content/f5cbeb41-c56f-47fb-9493-f7b965cb3768/pb4.jpg#%7B%22uuid%22%3A%22a238ca06-a2a1-428f-bda3-ec7686680f16%22%2C%22w%22%3A2000%2C%22h%22%3A1500%7D">The other side piece has 2 holes in the end, and it should slide into the grooves on the end that only allows it to drop down about ¼":<img src="https://media.printables.com/media/prints/596099/rich_content/4528d583-e7f5-4b9b-a660-f5f16165bed8/pb5.jpg#%7B%22uuid%22%3A%2251a41b39-64ba-4067-9c64-d0c3a38abd88%22%2C%22w%22%3A2000%2C%22h%22%3A1500%7D">Getting the Lid On or Off Now comes the tricky part. First note that as you turn the dial, the latches on all 4 sides will move in and out – from retracting flush to sticking out 2.5mm to sticking out 5mm. Moving these latches in and out in the right sequence will allow you to get the top in place.Start with all 4 latches sticking out an equal amount on all sides. Now, If you lift body of the box up, one side will.. drop down just a little, but the other will drop down enough to state sliding the lid on. As you start sliding the lid on, it'll go almost all the way. Next, fiddle with the dial until the lid can slide all the way on. (You're doing this blind, but that's what makes it fun!)Next, turn the dial until the final exposed latch, is flush with the end of the lid. Slide that end up flush with the top. Then rotate the dial some more until you can fully lift the second side of the box. Give the dial another 1/8th turn and everything is locked up! Just reverse this process to get the box back open.

Enigma Puzzle Box

puzzling

Cata3DD

This is a stronger spring for the 6-shot disc shooter.It is strongly reccomended to print it in PETG, pla will break after a few shots.

Stronger Spring 6-Shot Disc Shooter 

disk

SnapPrint3D_SuperCrazyPrints

Sign up Membership to get 15+ models every month. All models 3D Print Without Supports and (3MF,STL) file ready! <a target="_blank" href="https://www.supercrazyprints.com/" rel="nofollow noopener">https://www.supercrazyprints.com/</a>&nbsp;Check out my other models: <a target="_blank" href="https://cults3d.com/en/users/Scrazyone_SnapPrint3D/3d-models" rel="nofollow noopener">https://cults3d.com/en/users/Scrazyone_SnapPrint3D/3d-models</a>

Pokemon-Pikachu(NO SUPPORT)

Rock

RETIRED GUY 3D PRINTING

CROC SHOE JIBBITZFOUND SOME NAILS AND DIGITS AND RESHAPED THEM FOR ANGLES AND HEIGHTCREATED A FASTENING SYSTEM SO THAT THEY WOULDNT TOUCH OR RUB ON YOUR TOESA LITTLE SUPER GLUE ON THE PIN AND PUSH INTO TOE UNTIL IT BOTTOMS OUTFITS THE HOLES AND DEPTH PERFECTLYIMPRESS YOUR FRIENDS OR TOTAL STRANGERSTHANKS FOR LOOKING AND HAPPY PRINTING

CROC TOES JIBBITZ

funny

waltersworld3d

<a target="_blank" href="https://www.patreon.com/waltersworld" rel="nofollow noopener">https://www.patreon.com/waltersworld</a>&nbsp;Be sure to check out our Patreon for all newly released models, monthly giveaways, and the opportunity to have models designed custom for you!&nbsp;🕷️ Swing into Action with our 3D Printed Miles Morales Figure! 🌐&nbsp;Embark on a web-slinging adventure with our L3GO-inspired Miles Morales figure, standing tall at approximately 8 inches! With articulating arms, legs, and hands, this masterpiece captures the essence of the Spider-Verse&#39;s sensational hero.&nbsp;&nbsp;

Bricks Miles Morales Spider-man

Charlie

Sakul

Cozy Minecraft Lamp compatible with the BambuLab Led Lamp Kit. Bring this comfy lantern from your favorite block game to your home and use it as a desk lamp or even as a night light. No glue, screws, or additional parts needed, the complete lamp is assembled with 3D printed clips, making the build process straightforward and fun.No AMS needed. The Lamp Kit can be found <a target="_blank" href="https://us.store.bambulab.com/products/led-lamp-kit-001" rel="nofollow noopener">here</a>! The LED Kit works great with a standard smartphone brick or a power bank, making the lantern a portable option as well. How to build: The whole lantern is assembled using these 3D printed connector clips. You need 14 of those.<figure class="image image_resized" style="width: 31.27%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-01-28_5bf6ea8a01c34.jpg"></figure>Print all the parts and start clicking the upper part together. If you need to remove a clip again, it&#39;s best to use some pliers.<figure class="image image_resized" style="width: 85%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-01-28_ea97b21669c86.jpg"></figure>Next, connect the side blocks to the bottom part and add the LED light by simply pressing it in from the bottom. There are also some TPU feet you can add to the bottom part, but that is optional.<figure class="image image_resized" style="width: 84.44%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-01-28_f5cddf280a52a.jpg"></figure>Now slide the window parts in from the top. You can achieve many different looks by playing around with the choice of color here. For the original looks, normal yellow or blue filament works great.<figure class="image image_resized" style="width: 35.46%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-01-28_c310a536111c8.jpg"></figure>Lastly, put the top and bottom part together and enjoy!<figure class="image image_resized" style="width: 35.19%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-01-28_0c134d5dabc89.jpg"></figure>&nbsp;&nbsp;If you like my work and want to support me in creating more free original designs, I would very much appreciate it if you <a target="_blank" href="https://ko-fi.com/sakul" rel="nofollow noopener">“buy me a coffee”.</a>   Check out my newest Uploads:&nbsp;<figure class="table" style="width: 96.81%"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image"><a href="https://makerworld.com/en/models/484385#profileId-396742" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-06-04_0f30fee0f9ea4.jpg"></a><figcaption>🍦Pop &amp; Catch Toys Ice Cream Cone🍦</figcaption></figure></td><td><figure class="image"><a href="https://makerworld.com/en/models/457919#profileId-365927" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-05-08_184f6d673bf23.jpg"></a><figcaption>🐺🦊Minecraft Forest Animal Pack🐝🐇</figcaption></figure></td></tr></tbody></table></figure>

Cozy Minecraft Lantern for LED Lamp Kit 001

Light kit

PartyLime

GEN 12: please see my profile for the GEN 12 ball. There&#39;s a limit of 500mb on one page so I had to make another for the latest Gen. It bounces really well and feels super durable in TPC I wasn&#39;t satisfied with the current models of the airless basketball on here as they only had a single lattice. This took me days make sure the double lattice worked in CAD - SolidWorks was not built for this! As I don&#39;t have $2,500 to spare, I worked from the images available online.I printed it in TPU. It doesn&#39;t bounce as much as a standard basketball in TPU so I suggest a stiffer material.&nbsp;GEN 9: I have added a gen 9 version. It is a little closer to the original and should weigh about the right amount when printed in TPU/PLA&nbsp;GEN 10: I have adjusted the size of the hex holes and increased the filled on them. I&#39;ve also increased the lattice thickness to 8mm to hopefully increase bounce. The logo on the top and the airless gen 10 tag have also increased in size a little to improve how they look. Lastly, the holes around the seam are now pentagons as in the original ball&nbsp;GEN 11: I have added a new version with cut-outs throughout the seams. This will hopefully make the bounce more consistent.&nbsp;The original version I uploaded was removed due to “abnormal download data”. MakerWorld support took all my points but said I could re-upload so here it is again. Hopefully that won&#39;t happen again. MATERIALS:Extrudr Hard TPU (58D) - good durability about 40% bounceOverture Super PLA+ - 100% bounce but broke easilyOverture easy nylon (PA6) - broke almost instantly (the community have suggested “annealing” the print in water to increase durability)BASF Forward AM Ultrafuse TPU 64D - good durability and 60% bounce (BEST SO FAR)BASF Ultrafuse TPC 45D - good durability and great bounce. I recommend annealing this one at 110°C for 10 hours at least.

Airless basketball

RobDrivesCars

This model has been updated to a new link on 06/29/2024&nbsp;Rick Roll QR Code adapted from a TV model. It links directly to an autoplay video with no ads. The corners have been filleted.&nbsp;This is pre-sliced as a multi-color print for your printer with an AMS. Just print and go!

Rick Roll QR Code - UPDATED - No Ad, Autoplay, RTP

useful 

Balzo98

An easy to print frog! No support needed!

Easy To Print Frog

Rachel

Crafty Sven

No supports needed. Make sure that the bed is clean and the first layer adheres properly, glue is recommended.&nbsp;Good luck and happy printing ! ^-^&nbsp;I suggest trying the non AMS version 1st to see if you like the design and size. &nbsp;You can scale this up to 150% !

Ancient Guardian Articulated from Zelda 

cool

Cj 3DPRINT

Quick and easy to print cat bookmark.&nbsp;Link Here to see my other design:<ul><li><a target="_blank" href="https://makerworld.com/en/u/115355792" rel="nofollow noopener">https://makerworld.com/en/u/115355792</a></li></ul>Please put a like it's always a pleasure and follow me and sharing your prints 🙏🙏🙏.&nbsp;Printing instructions :0.2mm layer height2 walls10% infill