c.diedrich85

Asdfgasdfg

Be careful downloading prints called “Fast” etc, those might be faster but that's because of a weaker design, they are spammers just taking the original profile, lowering the integral strength to get it to print faster, and as explained below, there needs to be a balance in the force of the spring and the rubber band. Those profiles might not work as well as intended. Its just spammers racing to the bottom, give them enough attention and soon there will only be profiles with 1 wall and 2% infil thats printed in 5 minutes but falls together if you look at it long enough.&nbsp;Double action OTF fidget toy for the fidget toy design competition.&nbsp;All you need is plastic and a rubber band!&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/234870/2023-11-13_2404c2f7a37e2.gif">&nbsp;If you like the idea but dislike the design bookmark the model and visit it after the competition is over and I will release all the source file so you can easily modify the body or blade/comb!&nbsp;<h2>Assembly instructions:</h2>NOTE: For the double action to work you need to have a balance between your rubber band and the springs holding the blade. You can use the strongest rubber band you can find and it wont really matter, but the switch will be harder to push. So you might want to try around with different rubber bands or different materials for the springs. If the switch is to hard for your liking, your rubber band is to strong. If the blade/comb does not fully extract or retract, your rubber band is to weak or your springs are to stiff.&nbsp;<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=rN4wuBX-5q8"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/rN4wuBX-5q8" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;&nbsp;<h2>How it works:</h2><img src="https://makerworld.bblmw.com/makerworld/draft/234870/2023-11-18_6157ed5d0cf8b.png">

Double Action OTF Knife/Comb

Gimmicks 

laisch

<blockquote>Info: The wrench fits for anglegrinder nuts with 35mm hole circle diameter. But like some comments mention there are also other types of nuts with 28 or 20 mm hole distance. Check your dimensions before you print it</blockquote><figure class="image image_resized" style="width:32.61%;"><img src="https://makerworld.bblmw.com/makerworld/draft/165220/2023-11-12_c39e11d978104.png"></figure> Found this Idea in the video of pocket83 and had to do a 3D printed version of it<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=SoMkAkV62v0"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/SoMkAkV62v0" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>The model prints without supports if you use 0.2mm layerheight.&nbsp;For furhter hardware you need at least 2 M5x20mm hex nut screws. You can screw them directly in to the model. If the fit is too tight you can tap the holes before screwing the screws in.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/165220/2023-11-03_tkq9czc274jr.jpg"></figure>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;

Quicky (Angle grinder wrench)

Werkstatt 

TheBear

<h3>Ho Ho Ho, and a Merry Christmas! </h3>Presenting the 5 gram Christmas Gift Bow!Easy to print, easy to assemble and easy to enjoy! Personally, I suck at making a nice bow on Christmas Gifts. I am, however, quite good at letting my 3D-printer do the work for me, while I sit back and relax. So, here we are! (Make sure to check out my <a target="_blank" href="https://makerworld.com/en/models/79308#profileId-86446" rel="nofollow noopener">Christmas Twisting Ornament</a>, for another great, low-weight Christmas print!) Update: A smaller version at ~3.4 grams is also available now!Be aware that the smaller version does require tighter bending, so the flexibility of your PLA needs to be even higher. I have tested it with a few of the regular PLAs I currently have in stock, and all worked fine. But your mileage may vary. Just be extra careful when bending. And if it keeps failing, consider just sticking to the standard version or follow the tip at the bottom of this description :-) <h2>Assembly</h2>Assembly is done by first feeding the top ribbon through the slots at the bottom, and then pressing it onto the circle mount in the middle (slightly bending the ribbon first does make the assembly a bit easier - please refer to my poorly filmed assembly video below). After that, the rest of the ribbons can be inserted under the middle and pressed onto the circle mount in any order, you like! The ribbons are supposed to be a bit tight, when pressing them onto the ‘circle mount’ - this is to ensure they stay in place, without having to glue everything in place. I wanted this bow to require no additional materials to assemble! <img src="https://makerworld.bblmw.com/makerworld/draft/275104/2023-11-22_30c06d4ef46c.gif"> If you find the fit to be a bit too tight or a bit too loose, please try changing the X-Y Hole compensation in the Quality-tab in the slicer: <img src="https://makerworld.bblmw.com/makerworld/draft/275104/2023-11-22_100b874fe1c26.png"> Now all that is left to do, is to attach the bow to the gift using some glue/tape/etc. <h3>Filament to Use</h3>I've personally succesfully printed and assembled the bow with both cheap, generic PLA, brand name PLA, PLA+, High-Speed PLA, etc. However, Silk PLA, Matte PLA and other “special” types of PLA might not work as well, as they can be too brittle to bend like this. You could try placing the print on the hot bed, set to 70-80 degrees, to heat up the bow after it has been removed from the build plate. That will soften up the PLA and might make assembly with these materials possible. I personally haven't tested this yet, so I won't guarantee anything :-) Shout-out to Paul Elrod for this idea of heating up the print using the hot bed prior to assembly. If you have issues with the ribbons creasing/breaking, it is often due to how the lines line up with the bend. Changing the Top and Buttom Surfaces to either Concentric can mitigate this issue. Increasing your wall count is also one way of making the print stronger! Merry Christmas and Happy Printing!

Christmas Gift Bow (Foldable)

deko

cm3dshop.de

Poop Chute for Paving stone / Cobblestone / Flagstone users with Tray and hidden Handle&nbsp;Easy acess to the Poop with a pull out tray (if you got low space behind and besides the printer)&nbsp;stays in place with 3 round Magnets (attached to the printer) d=6mm ; thickness 4mm (3mm will also work when not pushed all the way in)&nbsp;tray can be hold closed with 4 magnets (Attention at the polarity!) …just optional&nbsp;hidden handle with Bambu Logo for pull out the tray : flat with front when closed ; for opening push the top part in and then pull at the lower part…very simple and easy…fully printed&nbsp;optional Lid for "clean design"&nbsp;&nbsp;This Version is only for Users who using a Paving stone/cobblestone / flagstone 400x400x40mm and 5-10mm rubber mat.It gives additional Space for the Poop…but of course it takes a bit longer to print. ;)&nbsp;Find the Original design (without using a flagstone here: <a target="_blank" href="https://makerworld.com/en/models/76241#profileId-80830" rel="nofollow noopener">https://makerworld.com/en/models/76241#profileId-80830</a>&nbsp;Improvements to the Original Post:&nbsp;-more Space for Poop&nbsp;- deleted the 2 magnets on the side because the printer isn't magnetic there (of course ;) )&nbsp;- give Space for the flagstone and rubber mat at the sliding area&nbsp;- made the back of the slide a bit higher (where the poop arrives) to get a bigger range for the heigth of the rubber mat → rubber mat + Stone = 45-65mm&nbsp;ATTENTION: the print profile uses the PETG/PLA trick so get a super smooth interface between the Tray and the supports!&nbsp;&nbsp;At All it is still a bit over engineered … but…does it really matter?! ;)&nbsp;Just let me know in comments when you have suggestions for improvement.&nbsp;&nbsp;

Gimmicks

Werkstatt

deko

p1s