Printed these for the wife's book shelf. Perfect for displaying! Printed one of each long and normal length. The only things I was not a fan of was the edge of the screw heads where they meet the build plate(I'm lazy and didn't want to do any post production work) and the pad that clamps the bottom of the shelf does not rotate freely. To solve both of these I just did up a couple TPU caps.

I shrunk this down to 85% and printed with my A1 mini, was a little concerned it was going to loose too much detail but came out absolutely gorgeous. The wife was actually crying a little bit. printed the "Love" face plate and body for the inserts in Elegoo red PLA+, the rest was in Bambu Labs Jade White PLA Basic. for lighting a fit a whole fairy light string in there for both white light and multi color. This was a 10/10 for sure.

I had a bit of an odd use case for this one. Pulled it into studio, did some measurements and actually didn't have to adjust anything for my needs. a door inside my air exchanger broke a little tab off and caused my humidity to shoot to near 60% as no air was venting to outside and just recirculating inside. the PLA one is holding for now but also sliced one up for strength in PETG and it's sitting ready to go if the PLA one breaks. Thanks for for the upload! made my repair super quick and easy!!

absolute 10/10 printed in translucent white PETG. Printed as a gift to pair with some thank you tall boys for someone who did me a solid helping at my house when I was out of town.

Printed one, my mother-in-law loved it... So I had to print my wife another one! Great model and easy print

Loved it! however my sister-in-law stole it, haven't printed myself another yet. Going to try and cut it in half and hide a joint somewhere so I can double the size of it on my lil A1 mini.

Printed clean - from app, thanks for the sweet slice job for me being lazy! Works flawlessly, also hooked into the pamphlet slot above the drink tray on the plane in the picture... but definitely didn't take some moderate turbulence lol. when locked into the drink tray in the closed position they weren't going anywhere!

I have to turn my steering wheel upside down on both my personal and service truck. However it works perfectly in Komatsu 930E/980E. Will be sending a boost off for this! I may try re-working it a bit to work in my service truck steering wheel in the normally positioned parked stance.

Printed flawlessly from the app, thanks for a great print file!

I had some very minor issues, slowed print down and everything came out wonderfully.

Came out amazing. The wife approves biggly. A1 mini

Perfect print! sealed my DIY dry box very well Editing after having this gasket installed on my bins for a couple weeks. These dropped my measured humidity from minimum 20% in my bins to every one is holding at 10%. Cant recommend this seal enough!!

Printed for my son's computer desk. Dimensionally correct and feels sturdy.

This came out absolutely stellar off my A1 mini with Elegoo tri-color Silk PLA. I do have an issue but it's likely 1000% my fault *facepalm* This was my first attempt at a larger print with silk PLA. I spent a boat load of time tuning for the perfect shine, no stringing and great print quality. and I'm pumped with how well this turned out! I am at an impass that I'm sure has no solution other than print it again 🥲. The ball and socket of the wings are solid. has anyone had success with remeding this? The jaw, joints and folding part of the wings work perfect. Just failed the ball and sockets. I should have used the silk profile? but I had spent so much time tuning for this specific material. Any ideas would be greatly appreciated!!

Only complaint I have is they want to fall away from the other. My solution was simple though, I super glued Popsicle sticks to the bottom. 7 in total 3 connecting the two that don't have connectors and 2 on each pair that has connections. asides from an easily remedied issue these work perfect.

I printed these to run in my diy Ikea drybox. Printed with no issues in PETG

quick and very effective print!

Printed for the door of my outdoor kitchen on the holiday trailer. Perfect for it's slim design and high functionality. I glued the spring's. This design just works well!

These clip firmly in place. Used a bunch at home and have a bunch in my work bag that gets moderately abused and thrown around. All my cords and cable stay tangle free now. Thanks for the wicked deadly design and print profile!