Loonie Printing

SkyDawgie

I&#39;ve created a flag mounting solution for the broken hardware to mount my flags to the pole. I wanted something that would likely not come apart in high wind. It&#39;s semi-permanent but you can unscrew the wood screws and slide them off the pole. So you can print a set of these for each flag that you want to attach to the pole.&nbsp;**Does require some common hardware and tools for assembly**&nbsp;This model features:<ul><li>Anti-sliding - Flag doesn&#39;t slide up and down the pole</li><li>Free spinning - Print in Place assembly keeps the bushing in place while allowing it to free spin in the wind</li><li>Swap-able - unscrew the clips to slide the flag off the pole and slide another flag back on</li></ul><h4>Bill Of Materials</h4><figure class="table" style="width: 40.13%"><table class="ck-table-resized"><colgroup><col><col><col></colgroup><tbody><tr><td colspan="3">Hardware</td></tr><tr><td>No.</td><td>Item</td><td>Quantity</td></tr><tr><td>1</td><td>#4x1/2” Wood Screw</td><td>4</td></tr><tr><td>2</td><td>1/8”x1.5” Steel Dowel</td><td>2</td></tr></tbody></table></figure>Tools Required<figure class="table" style="width: 40.29%"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td colspan="2">Tools</td></tr><tr><td>No.</td><td>Item</td></tr><tr><td>1</td><td>#1 Phillips Screwdriver</td></tr><tr><td>2</td><td>Angle Grinder or Dremel with cut-off wheel</td></tr><tr><td>3</td><td>Sharpie</td></tr><tr><td>4</td><td>Safety Glasses</td></tr><tr><td>5</td><td>Vise or Small Hammer</td></tr><tr><td>6</td><td>Drill</td></tr><tr><td>7</td><td>1/8&#34; Drill bit</td></tr></tbody></table></figure><h3 style="text-align: center">Assembly Instructions</h3><ol><li>Print Plate</li><li>Drill out the cross hole for a clearance fit to the rod<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465501/design/2024-05-15_a3c11339e56fb.jpg"></li><li>Cut the dowel pin stock into 2 rods at 1.5 inch length<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465501/design/2024-05-15_016b47b48a1d98.jpg"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465501/design/2024-05-15_6bc22faa9caf38.jpg"></li><li>Push rod through the clearance hole on the bushing<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465501/design/2024-05-15_598a4a1ae97768.jpg"></li><li>Place the Hook through the flag and stretch around the 1/8&#34; rod<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465501/design/2024-05-15_da7a4980dc225.jpg"></li><li>Either using the vise or by tapping lightly with a hammer, press the Hook onto the 1/8&#34; rod<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465501/design/2024-05-15_7bc1d4f7b774c8.jpg"></li><li>Repeat for other flag mounting clip</li><li>Slide the Mounting clips onto the flagpole<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465501/design/2024-05-15_1ca6ae5303222.jpg"></li><li>Screw the wood screws into the holes in the Bushings. Leave some slack as if the Hooks are free hanging down. Don&#39;t pull the Hooks tight against the flag.<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465501/design/2024-05-15_304aeba2c885e.jpg"></li></ol>&nbsp;&nbsp;

flag pole clips