bravling

Knolliwood

Printed with PAHT-CF&nbsp;But ABS should also work because of the car temperature

SMART Smartphone holder

auto

tlavedas

I used HueForge Lithophane Blending Type and an AI created image to make this “stained glass&#34; Macaw print in TWO parts. The first part has white, blues and black of the foreground. The second part blanks out parts of the bird and provides the reds and yellows for the background. The image halves are tailored to yield green leaves, though no green filament is required for either half of the model.Both parts have very thin base layers, so special care is needed to remove them from the print bed. It is probably best to cool them completely before trying.When joining the two parts be sparing with the adhesive, especially in the lighter parts. The adhesive will change the colors if it is not behind the black or red parts. I just used some around the black parts and around the very edge to keep the glue from showing. If spread thin and uniformly, it should not show too much.It uses 0.08mm layers to speed printing with minimal lose in detail.&nbsp;Part 1Project: Macaw_Part_1.hfp Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmThe Model is 150x167.49mm in size You may print at higher layer heights below the Min Depth of 0.16mm The Max Depth is 1.4mm and the Actual Depth is 1.3mmFilaments Used: PLA PolyLite Natural Transmission Distance: 21 PLA PolyLite White Transmission Distance: 5 PLA Overture Blue Transmission Distance: 4.2 PLA HueForge Navy Blue 2.2 Transmission Distance: 4 PLA PolyLite Black Transmission Distance: 0.3 This print uses 5 unique filamentsSwap Instructions: Start with Natural At layer #2 (0.24mm) swap to White At layer #4 (0.4mm) swap to Blue At layer #8 (0.72mm) swap to Navy Blue 2.2 At layer #14 (1.2mm) swap to Black for the rest.&nbsp;AMS/MMU users with four slots will need to manually swap out the natural filament for black on the first part once the initial two layers are done and before the Navy Blue is finished.&nbsp;Part 2Project: Macaw_Part_2.hfp Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmThe Model is 150x167.49mm in size You may print at higher layer heights below the Min Depth of 0.16mm The Max Depth is 1.4mm and the Actual Depth is 1.4mmFilaments Used: PLA PolyLite Natural Transmission Distance: 21 PLA Polylite TD1 Lemon Yellow Transmission Distance: 5.5 PLA Overture Red Transmission Distance: 4.8 PLA PolyTerra Army Red Transmission Distance: 0.3 This print uses 4 unique filamentsSwap Instructions: Start with Natural At layer #2 (0.24mm) swap to Lemon Yellow At layer #5 (0.48mm) swap to Red At layer #12 (1.04mm) swap to Army Red for the rest.&nbsp;If substituting filaments, pick ones with the closest TD values. Use a Natural white, if possible. Otherwise, pick the one with a TD &gt; 10 to minimize the color change it will cause.

HueForge Stained Glass Macaw

stained glass

ozarkexpeditions

<h2>Customizable Brand Name Compatible Bricks – Now on MakerWorld!</h2>I&#39;m thrilled to share these fully customizable compatible bricks with you! This is the most complete brick designer that you&#39;ll find on MakerWorld and we&#39;re excited to see what you create. With this SCAD generator, you can create a wide variety of compatible bricks tailored to your needs. Whether you&#39;re a hobbyist, a maker, or just looking to enhance your building experience, these customizable bricks will add a new level of creativity to your projects.<figure class="image image_resized" style="width: 40.84%"><a href="https://makerworld.com/en/models/492674#profileId-406303" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000479021/design/2024-06-11_06aac4d169af5.png"></a><figcaption>📢 New! We&#39;ve just released the <a target="_blank" href="https://makerworld.com/en/models/492674" rel="nofollow noopener">Brick Your Name</a> customization tool. Give it a try today!</figcaption></figure><figure class="table"><table><thead><tr><th colspan="6">So many options!</th></tr></thead><tbody><tr><td>Bricks</td><td>Wings</td><td>Slopes</td><td>Curves</td><td>Baseplates</td><td>Rounds</td></tr></tbody></table></figure><figure class="image image_resized" style="width: 73.61%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000479021/design/2024-05-29_56a563fc19249.png"></figure><blockquote>I have received written permission from the original author, <a target="_blank" href="https://github.com/cfinke" rel="nofollow noopener">Christopher Finke</a>, for the OpenSCAD model and am publishing this under the same MIT license. Check out the original repository on GitHub <a target="_blank" href="https://github.com/cfinke" rel="nofollow noopener">here</a>.</blockquote><h2>How to Customize Your Bricks</h2>Step 1: General Settings<ul><li>Block Width: Set the width of the block in studs.</li><li>Block Length: Set the length of the block in studs.</li><li>Block Height Ratio: Choose the height ratio (e.g., standard brick height, plate height, etc.).</li><li>Block Type: Select from Brick, Tile, Wing, Slope, Curve, Baseplate, or Round.</li><li>Block Brand: Choose the size and compatibility.</li></ul>Step 2: Shape-Specific Settings<ul><li>Customize additional settings specific to the block type you selected (e.g., wing type, slope height, curve type, baseplate, round radius, etc.).</li></ul>Step 3: Advanced Settings<ul><li>Stud Type: Select between solid or hollow studs.</li><li>Block Bottom Type: Choose between open or closed bottom blocks.</li><li>Wall Splines: Include wall splines for better stability (valid for open bottom blocks).</li><li>Technic Holes: Add horizontal or vertical holes for Technic compatibility.</li><li>SNOT (Studs Not On Top): Option to place studs on the top and bottom or no studs on either side.</li><li>Dual-Sided and Dual-Bottom Options: Customize stud configurations for dual-sided or dual-bottom bricks.</li></ul>Step 4: Printer-Specific Settings<ul><li>Use Reinforcement: Include extra reinforcement for easier printing on FDM printers. This is set to ‘yes’ by default. </li><li>Stud Rescale: Adjust the stud diameter for your specific printer settings.</li><li>Stud Top Roundness: Specify the roundness of the stud tops.</li></ul>Tips<ul><li>Customization: Experiment with different stud shapes and internal structures for unique designs.</li><li>Compatibility: Ensure for accurate sizing by printing </li><li>Personalization: Use custom colors options to create personalized bricks for special projects. Use the color painting features in Bambu Studio to make you bricks even more unique. </li></ul>Important NoteThis customizable model is designed for personal and educational use and not for commercial reproduction or sale under these brand name trademarks.&nbsp;Feedback WelcomeI hope you enjoy using this customizable brick generator. Your feedback is invaluable, so please let me know if you have any suggestions or improvements. Together, we can make the MakerWorld platform even better!&nbsp;Explore More of Our Models! <a target="_blank" href="https://makerworld.com/en/models/463568" rel="nofollow noopener"><img class="image_resized" style="width: 29.54%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000479021/design/2024-05-13_0d1f6d3fca672.png"></a><a target="_blank" href="https://makerworld.com/en/models/452361" rel="nofollow noopener"><img class="image_resized" style="width: 25.72%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000479021/design/2024-05-03_52b9e8ccc8501.gif"></a><a target="_blank" href="https://makerworld.com/en/models/390175" rel="nofollow noopener"><img class="image_resized" style="width: 30.63%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000479021/design/2024-03-23_20f08dbba5d8e.gif"></a>

Ultimate Brick Customizer on MakerWorld!

lego 

DINO2211

Funko Pop vierge

funko

asquared

Turn your Blink camera into a bird feeder cam! The bird feeder screws into a post/fence using (2) #8 or #6 wood screws and the Blink camera (3rd Gen & 2nd Gen) snaps into place.Three sizes available for printing (no supports needed).

Blink (3rd Gen) Bird Feeder

bird

Daniel's

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm <img src="https://makerworld.bblmw.com/makerworld/draft/414104/2024-01-16_18125a27c787b.jpg"> Swap Instructions:Start with BlackAt layer #9 (0.48mm) swap to Jade White for the rest.&nbsp;

Octopous - HueForge

hueforge

JamesThePrinter

Your cat must move the sliders to uncover treats. The wells are deep enough to fit most treat sizes or a few pieces of food. Your cat can either eat the treat directly from the well or use their paw to remove it. Two slider designs are currently available - plain or ladybug. Once 3 sliders are placed on the base, simply place the top in position and gently press down to snap it in place.&nbsp;<h5>Print Settings</h5>Although no special settings are required, a higher infill percentage is helpful to add extra weight to the print. This will make it easier for your cat to move the sliders without the entire toy sliding around. If printing the ladybug sliders, use a color change for the last 0.4mm.&nbsp;<a href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow">Buy Me A Coffee</a>&nbsp;The following filaments were used in the pictures above:<ul><li>Prusament Azure Blue PLA</li><li>Polymaker PolyTerra Lava Red PLA</li><li>Polymaker PolyTerra Charcoal PLA</li></ul>

Cat Treat Toy

cats

m.cody.sims

Just a good Mando helmet!&nbsp;My profile doesn&#39;t have support on the inside of the helmet because I have found it didn&#39;t really help that much with the quality and it used a lot of filament. the very center of the inside will be rough because of this but it hasn&#39;t been an issue for me.&nbsp;For those wondering what I use for a face sheild I use a Hobart 770580 Face Shield Replacement Lens, Shaded from Amazon. I cut it to shape and use a little bit of hot glue along the front and near the temples. That seems to be enough. I would recommend getting air soft helmet padding for a custom fit and comfort.&nbsp;If you like my work, please consider supporting me by boosting my model or <a target="_blank" href="https://www.buymeacoffee.com/m.cody.sims" rel="nofollow noopener">buying me a coffee</a>!

Mandalorian Helmet One Piece

lamp

LoboCNC

<figure class="media"></figure>Has holiday stress got you tearing your hair out? Watch this mesmerizing sculpture for 3 minutes and your angst will melt away!This mini-sized reinterpretation of <a href="https://www.printables.com/model/284127-kime-fully-3d-printable-kinetic-sculpture" rel="nofollow">Noci's KiMe kinetic sculpture</a>, at 6.9"/175mm in diameter, is easy to print and assemble. Instead of the clockwork mechanism for reversing the spinners, it uses two completely independent spinners driven by weights and strings wrapped up on spools. The direction is reversed when the string completely unwinds from the spool and then re-winds in the opposite direction, driven by the inertia of the spinner. (The tips of the spinners are weighted with either 2 US pennies, or 2 Euro 2 cent coins). It'll run for about 3 minutes with a quick flick of the spinners. In addition to the 3D printed parts you will need: 4 - 3mm bore x 10mm OD x 4mm thick bearings (623ZZ) 1 - 100mm length of 3mm diameter rod 2 - M6 bolts (and maybe a couple of M6 nuts) 48 - coins: US pennies or Euro 2 cent Fishing line or heavy-duty sewing thread.Printing Print 2 of the spinners, 2 of the weights, and 1 each of the wall mount, washer and cap. I used PLA and 0.2mm layers, but I don't think either are critical. But make sure you set the speed for small perimeters very low (~20mm/s) so that the tiny hole in the hub of the spinner doesn't close up. Note: I've provided weight-xxx.stl files for both ¼-20 bolts and for M6 bolts.Assembly 1. First make sure that all 4 of your bearings will slide easily over your 3mm rod. If your rod is a little over sized, put it in a drill and sand it down with 400 grit emery paper. Then tap the rod into the wall mount piece until it is flush with the back. Screw the wall mount to your wall using 2 drywall screws, at least 1m above the floor or other obstacles.2. I highly recommend washing the lubricant out of your bearings. Under light load, bearings run more freely dry. I used WD-40 and then blew them out with compressed air, but you could use almost any solvent, like alcohol. Press the 4 bearings into either side of the two spinners.3. Cut two 1m lengths of thread or fishing line. Tie a fat knot in one end. Thread the un-knotted end into the small hole in the backside of the spinner and feed it through the front side. (Do this for both threads and spinners.) The knot should fit into the little pocket on the back side of the spinner. Trim off any tails.4. Press stacks of 2 pennies each into the slots at the ends of the spinner arms. Note: US pennies changed weight in 1982, so make sure all of your pennies are from before, or all after 1982. If the coins are loose, lock them in place with a dot of superglue.5. Slip one spinner onto the 3mm rod, spool side first. Next slide the washer over the rod, then the other spinner so that the two spinners are back-to-back. Finally, press the cap onto the end of the rod.6. Thread an M6 bolt into each of the weight pieces, maybe with the addition of a nut or two for added weight. Tie the free end of each thread onto the top of the weights. Each weight should be somewhere in the 5 - 10 gram range. You want just enough weight to make the spinners turn when they are at a standstill. More weight won't hurt, but your sculpture will spend more time spinning at high speeds, which is less visually interesting.Operation To make it go, just simultaneously flick each spinner in opposite directions. This will start winding up the strings on each spool. Ideally, you want both weights to lift up about the same amount. If simultaneous flicking is a little challenging, just slowly wind up each string on each spool, turning the spinners in opposite directions. Then let them go at the same time.&nbsp;

Easy Kinetic Sculpture

kinetic

harrypulvirenti

It is basically an optimisation of the original design but is functionally the same. This remix eliminates a rear wall to use less material and makes overhangs less pronounced to make the model easier to be printed. I strongly recommend using brim to print it if you don't want to see the heel fall.You can find the suggested orientation used to print the object in the images.With the proposed orientation the object should fit without scaling it, you will maybe just need to move it a little bit into position, but some user reported that scaling it down to 95% also works well. &nbsp;I tested it with my X1C and is perfectly compatible. About the P1P the original model was compatible with the P1P without enclosure and this remix have the same compatibility

Bambu Lab - Filament Poop Bin - X1, X1C, P1P and P1S

bambu stuff

RileyDesigns

This is dragon scale chainmail, a print in place multi-use flexible fabric. This chainmail can be used from anything from a satisfying fidget toy to an integral part of you cosplay or costumes. This model is strong so feel free to play till your hearts content or weather it to deataile a costume. This model can be colored via bambu studio. For best results use a small layer height, but .2 works just fine. I have included multiple models in the raw model files including a single piece so you can make your own custom shapes. Everything but the single chainmail link stl file is reduced so it slices fast so beware of using high resolution shapes with this model (before this model was redeuced at a 20x20 chainmail it was over 34 million triangles). If there are any shapes you would specifically like Id be happy to make them and upload it as a profile.&nbsp;MeasurementsEach side of the hexagon is 7mm in lengthDistance from center to center to link the chainmail together should be 13mm horizontally, and to get the second row of chainmail is over 6.5mm up 11mm&nbsp;Commercial licenseI have a commercial license available at <a target="_blank" href="https://cults3d.com/en/3d-model/fashion/dragon-scale-chainmail-commercial-use" rel="nofollow noopener">https://cults3d.com/en/3d-model/fashion/dragon-scale-chainmail-commercial-use</a>feel free to send me a message on Makerworld to confirm this is the right model. Or send me a DM for a comercial lisence if you dont want to go through cults3d :)

Dragon Scale Hexagonal Chainmail - Print in place

fabric

FilliFuu

Cutie Cloud Jumper Dragon Flexi-Fit (Special Articulated) Model With Multiple Choice Of Wing Designs&nbsp;Based on the dragon cloud jumper from the movie ‘how to train your dragon 2’ - Built with articulated links using my self designed ‘flexi-fit’ chain. The flexi-fit design is an evolving experiment seen in previous models I have released and now been improved upon. It allows a standard articulated design to snap together to remain rigid for posing and support or simply for your own amusement.Improvements include -&nbsp;-Better and easier bridging.-Changed location of socket to allow greater pivoting-Slightly increased join size, tighter fit (can be eased with multiple uses)-Larger and extra walls for strength&nbsp;Still in early development, with your feedback I hope to improve even further for an awesome articulated design that is commonly enjoyed.&nbsp;Note *My First time printing with Bambulab exclusive filamentPrinted with the beautiful PLA Arctic Whisper, PLA Onyx Black Sparkle & PLA Basic Yellow & Red Thank you so much Bambulab for creating this fantastic and beautifully optimized filament.&nbsp;Model contents&nbsp;-Painted and unpainted variations/ miniature scale for A1 mini-Cloud Jumper base model and basic mini wings (for those who wish to use without large wings but choose to fill the wing sockets)-Solid wings, folded and spread, the cover photograph contains one of each, but your free to choose 4 folded or 4 spread if that's what you wish-Flexi wings, purely for fun based upon the ‘NASA fabric’ designs you may have seen by multiple other designers-All STL files associated&nbsp;-Additional profile for the solid wings, to anyone who may encounter issues printing the larger wing. I included this file which lays the wings as flat as possible to the bed, the rear of the wings quality will be likely be impacted and require cleaning, but have zero danger of the print collapsing, print only if you have issues with your tool-head knocking your prints.&nbsp;How to & Assembly&nbsp;Simply print the base model and your choice of wings, selecting whichever printer you are using.&nbsp;Once printed simply insert the wings into the correct sockets being careful not to damage your model, you may wish to lightly trim or sand the ball socket on the wing if required (see pictures & troubleshoot section below) and your done.&nbsp;To use the flexi-fit joins, pull the ball into the clip on each link, can be stiff at first but loosens up each time you use this function.&nbsp;Print is calibrated towards PLA basic. Tested successfully in silk at 120% (CC3C Silk no issues), I am unsure how strong the link will be when printed with silk but its generally not recommended for articulating models.&nbsp;Print Settings&nbsp;Printed multiple times in different sizes & filamentsFor those not using the 3.mf files here is what is recommended…Standard 0.42 wall/ 0.3 used on the outer wall for the main body to increase detail.No brim or support needed on the main file & flexi wings.brim and supports used on the spread wing, the folded wing recommended brim for better corner adhesion4 wall for strength25% gyroid infillz hop 0.4 on the solid wingsWall slowed to 120 however this is entirely up to you depending on what your comfortable printing&nbsp;Troubleshooting&nbsp;-Common problems I often hear can often be easily solved but simply cleaning your 3D print bed so if you have adhesion issues make sure to scrub your plate thoroughly using warm water and soap, rinse with hot water and air dry vertically. IPA is often recommended by most but I personally find standard dishwasher soap to be fine.&nbsp;-Other adhesion issues can be fixed using a brim, but is not recommended unless urgently required or specified in the print settings above.&nbsp;-Tool-head knocks print, I have added an easier print profile with is to be avoided unless required, this profile is labelled 'SAFE' use only if other methods fail. Other reasons for the tool-head knocking the print can be, z-hop required in your slicer settings (turned on by default in my uploaded profiles) Your printer belts may require tightening, carbon rods require cleaning and bearings require lubrication. Calibrate your filament and increases fan speed on your tool-head. If these all fail please use the profile listed earlier.&nbsp;-Ball sockets are too tight to insert, common but the sockets require a tight fit to remain rigid once inserted - its completely fine to lightly sand or even use clippers to slightly trip the ball to allow you to easily insert the socket while remain stable. This may be required depending on which filament you choose to print with.&nbsp;Any other issues please ask and I will help as best as I can, thank you.&nbsp;FIN&nbsp;

Flexi-Fit Cloud Jumper Dragon

cute

FunkyArt

A few years ago I made this as a rendering for my kitchen backsplash. At some point I thought, why not print it out and put it on a shelf?It's a tribute to the legendary photo from the New York Times "Lunch atop a skyscraper" and of course Star Wars. Now what has always belonged together comes together ...&nbsp;If you don't want to waste so much material or have problems while printing, try cutting the model exactly in the middle of the support surface, like here (or use the halfcut profile):<figure class="image image_resized" style="width:100%;"><img src="https://media.printables.com/media/prints/474202/rich_content/745475e4-d756-4984-b39e-6e8470fef94b/thumbs/cover/800x477/png/unbenannt.webp"></figure><figure class="image image_resized image-style-align-center" style="width:99.69%;"><img src="https://media.printables.com/media/prints/474202/rich_content/ba54fb57-f598-4b31-9bf8-5d75aba81fbe/thumbs/cover/800x600/jpeg/image3.webp"></figure>This makes it an pretty easy print (use tree support!) I glued the legs and the surface with plastic glue, it holds perfect and the result looks quite good.<figure class="image image_resized image-style-align-center" style="width:99.15%;"><img src="https://media.printables.com/media/prints/474202/rich_content/60e8a19b-5c21-493e-8e4c-e9037d5b321b/thumbs/cover/800x600/jpeg/image0.webp"></figure><figure class="image image-style-align-center image_resized" style="width:98.8%;"><img src="https://media.printables.com/media/prints/474202/rich_content/5468c86b-fb99-4dea-9c33-e2af387fe6d8/thumbs/cover/800x600/jpeg/image0.webp"></figure>&nbsp;

Lunch atop a shelf (StarWars Troopers)

star wars

The Big Greek

Phone Stand 2024 Hi I would like to introduce you to my Phone Stand 2024.I think phone stands are just great. They are easy and quick to print and you can never have enough of them :-)You don't need an AMS for this one. Just print all the parts, stick them together and you're done.&nbsp;UPDATE 14.03.2024&nbsp;<figure class="table" style="width:98.39%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td style="text-align:center;" colspan="2">Complete your desk with the 2 new models in the same design as the phone stand</td></tr><tr><td>Business Card Holder<a target="_blank" href="https://makerworld.com/en/models/253496#profileId-269932" rel="nofollow noopener">https://makerworld.com/en/models/253496#profileId-269932</a></td><td><figure class="image image_resized" style="width:30.52%;"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-03-14_e8318022c0223.jpg"></figure></td></tr><tr><td>Pen Holder<a target="_blank" href="https://makerworld.com/en/models/253471#profileId-269896" rel="nofollow noopener">https://makerworld.com/en/models/253471#profileId-269896</a></td><td><figure class="image image_resized" style="width:30.09%;"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-03-14_0b91c40d9d56a.jpg"></figure></td></tr></tbody></table></figure>&nbsp;&nbsp;<figure class="table"><table><tbody><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;text-align:center;">Also check out this Phone Stand if you are interested. Split-Phone-Stand 2024 <a target="_blank" href="https://makerworld.com/en/models/169860?profiled=186535#profileId-186532" rel="nofollow noopener">https://makerworld.com/en/models/169860?profiled=186535#profileId-186532</a></td></tr><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;"><figure class="image image_resized" style="width:167.885px;"><a href="https://makerworld.com/en/models/169860?profiled=186535#profileId-186532" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-02-03_2ad417cb9457e.jpg"></a></figure></td></tr><tr><td style="text-align:center;">UPDATE 03.02.2024  Also check out this Phone Stand if you are interested. It's a 3-ANGLE Phone Stand <a target="_blank" href="https://makerworld.com/en/models/169772#profileId-186430" rel="nofollow noopener">https://makerworld.com/en/models/169772#profileId-186430</a></td></tr><tr><td><figure class="image image_resized" style="width:18.65%;"><a href="https://makerworld.com/en/models/169772#profileId-186430" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-02-03_039c3598d2fbb.jpg"></a></figure></td></tr></tbody></table></figure>If you like my work/project consider supporting me with these options:<ul><li>leave a like</li><li>leave a comment</li><li>download the file</li><li><a target="_blank" href="https://www.buymeacoffee.com/thebiggreek" rel="nofollow noopener">or By me a Coffee</a></li></ul><h3>This article/post/text or the print profile as well as the finished print may not be used for commercial purposes.</h3>Have fun printingTBG&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_16be5c7fdcb9f.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_52fde81037999.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_4c5855c0935ab.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_e3ac89cf4bdd8.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_904b0eb62ac33.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_28f2834273aa7.png"></figure>Please no commercial use