bradmcgonigle

Apple

MEAF designs

Easy to print and fun to make!Perfect for your candy table, coffee table or any corner of your house&nbsp;&nbsp;Specially designed to fit in the buildplate of any mid size printer.The base is one piece. and every letter and details are separated files so you can print it in different colors even without an AMS.&nbsp;Designed two styles for every “O”. so you can choose what you like.<ul><li>First "O": choose between santa claus or tree ornament</li><li>Second “O”: choose between snowman face or snowman body</li><li>Third “O”: choose between reindeer or christmas elf</li></ul><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/1795494732/draft/2023-09-02_n84evi4tipld.gif"></figure>&nbsp;split the "Details" file in to parts with your slicer and just print the details you like for each one and glue them on top!<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/1795494732/draft/2023-09-02_o1xtzxx4tz4i.png"></figure>&nbsp;&nbsp;&nbsp;Print SettingsMaterial: PLA / PETGLayer height: 0,28 mm for letters and base. --- 0.2 for detailsNozzle diameter: 0,4mm or 0,6mmInfill: 10 -12%Perimeters: 2Supports: no&nbsp;Printing Tipthe tolerances are a little tight, so you will need some glue depending on your printer and/or filament calibration&nbsp;&nbsp;&nbsp;

Christmas hohoho Sign

Christmas

JamesThePrinter

** Get an early start! Get the <a target="_blank" href="https://makerworld.com/en/models/41177" rel="nofollow noopener">Christmas version</a> now! **&nbsp;&nbsp;Light up different Halloween scenes in this display. A tea light candle is required. The display features a door that opens to allow access to the tea light. Use a section of 1.75mm filament inside the hinge to connect the door to the case. Depending on your printer/setup, this hole may be on the tight side or a bit loose. If tight, drilling out the hole may help. If it is slightly oversized, I suggest melting the end of the filament piece with a soldering iron or lighter.I have included a separate liner. This allows you to print the case in a dark color, but line the inside with a lighter color to allow for more reflection of light outward, making everything brighter.For a complete display, you will need:<ul><li>1x Case</li><li>1x Door</li><li>1x Knob</li><li>1x Snap Ring</li><li>1x Liner - Optional</li><li>1x (minimum) Scene - You can easily remove the snap ring to swap out scenes as desired</li></ul>Check out my other holiday models <a target="_blank" href="https://makerworld.com/en/u/1360890085/collections/23941" rel="nofollow noopener">here</a>.<h4>Print Settings</h4>No special setting are needed for the display case, door, knob, snap ring and liner. &nbsp;Scenes Print SettingsPrint the scenes with 100% infill. The scenes also require color changes:<ul><li>The top 2 layers should be black</li><li>If there is no moon in the scene, all other layers can be white or clear - both look nice</li><li>If there is a moon in the scene, it will look best if the bottom 2 layers are printed in clear filament<ul><li>All other layers should be white</li><li>All non-black layers could be printed in all white or all clear if one isn't available to you</li></ul></li></ul>&nbsp;<h4>Assembly</h4>Glue the knob into the door. Only a very small amount is needed.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_njhnxlluv3as.png"></figure>Put the door in place and latch it. Use a 20mm piece of 1.75mm filament to connect the 3 sections of the hinge. If the filament goes in very easily, it may be a good idea to heat up the top end of the filament ‘pin’ and press it flat. This will prevent the pin from falling through later on.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_ps9jc73zrxio.png"></figure>Open the door. Insert a scene into the opening (image facing outward). Insert the snap ring behind the scene by gently squeezing and placing it into the groove (see red arrow below).<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_zosx4sj7pb0v.png"></figure>If you are using a liner, slide it inside the case. This may be a tight fit. Go slowly and be sure to slide it in evenly on all sides.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_t3jeg8v9f9hv.png"></figure>Turn on your tea light and close the door.&nbsp;&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The following filaments were used in the pictures above:<ul><li>Bambu Lab Matte Charcoal PLA</li><li>Bambu Lab Matte Ivory White PLA</li><li>GIANTARM Transparent Clear PLA</li></ul>