Björn Heirman

giuliolibrando

<h2>BambuLab AMS Silica Gel Box With Mi/Xiaomi Hygrometer - Full Set of 5 boxes</h2>The project comes pre-oriented on the build plate. No supports are required when printing the pieces. &nbsp;The hygrometer/thermometer just clicks in place. You can connect it to bluetooth and use it with Xiaomi Home app.If you want an accurate reading do not fill with silica the central one with the sensor.&nbsp;&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/141846/2023-11-03_62d3ec71aff83.png"></figure><h3> </h3>---------------------------It's available a variant of this model that use a different hygrometer sensor.You can find it here:<a target="_blank" href="https://makerworld.com/it/models/32780" rel="nofollow noopener">BambuLab AMS Silica Gel Box With Hygrometer - Full Set</a> <figure class="image image_resized" style="width:78.04%;"><img src="https://makerworld.bblmw.com/makerworld/draft/141846/2023-11-03_70cf6a32440d7.png"></figure>----------------------<h3>Hardware:</h3><ul><li>You will need <a target="_blank" href="https://amzn.to/47k53BB" rel="nofollow noopener">this hygrometer</a> </li></ul>&nbsp;<h3>The plates are divided by box type:</h3><ul><li>01 - One large central box with humidity sensor/thermometer</li><li>02 - Two large boxes </li><li>03 - Two small boxes for the sides (optional)</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/141846/2023-11-03_7c83b8f57eefe.png"></figure><h3>Assembly Istruction</h3><ul><li>Insert the side panels into the central box by sliding them into the grooves </li><li>slide the cover on the panel tracks until it bottoms out</li></ul>&nbsp;<figure class="image image_resized" style="width:69.41%;"><img src="https://makerworld.bblmw.com/makerworld/draft/141846/2023-10-29_9f250eb924e4c.png"></figure>&nbsp;&nbsp;&nbsp;&nbsp;---N.B. Do not remove the Object Modifiers from the plate 03<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/141846/2023-10-11_f2cb4a2b1ad76.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/141846/2023-10-11_75dde1a03ecf1.png"></figure><h3> </h3>&nbsp;

BambuLab AMS Silica Gel Box With Mi/Xiaomi Hygrometer - Full Set

laisch

This is a scaled flyable micro version of the ASW20 sailplane from Schleicher. The model was created to be lightweight and printable in normal PLA.Because of it's lightweight behaviour it's a little bit fiddly to get it together properly but it's still strong enouth to survive crashes. So please read the Instructions before you build it.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_7930ef971b4078.gif"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_b32700811d73d.gif"></figure>&nbsp;<h3>Printing:</h3>Make sure you align the STL-Files flat with the build plate like in the pictures.&nbsp;The Fuselage and the Nose have to be printed in Vase Mode (0.12mm) for best quality and perfect stability. Make sure you geht your part cooling right otherwise the thin tail section won't print properly because of overheating. Turn Bottom Layers to 1 Layer.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_2xua1hjiurid.jpg"></figure>The Wing parts are printed in normal Mode with 0.12mm Layerheight. Make sure that the first layer prints in 0.2mm.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_9yaljcx3l44z.jpg"></figure>After printing carefully remove the wings from your print bed and make sure not to overbend them.&nbsp;<h3>Assembly</h3>Clean up the parts from any print defects<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_mmrpjuqrlmyo.jpg"></figure>&nbsp;Testfit if the wings fit inside the fuselage. The reinforcement part of the wing should touch the fuselage. If not, just cut away the parts wich are too big.<figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_k461jxekhpvj.jpg"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_p3zauy5szoj1.jpg"></figure></td></tr><tr><td>Wing not aligned with fuselage</td><td>Wing aligned with fuselage</td></tr></tbody></table></figure>&nbsp;When the testfit is ok, put some superglue onto the wings and glue them in place.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_v2l13jrwi32n.jpg"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_4dvxkmto8krd.jpg"></figure>&nbsp;Make a testfit if the rudder fits in to the elevator. If not you can take a cutter knife to clean it up a little bit.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_hiskzgmshhkj.jpg"></figure>&nbsp;After that put the rudder and elevator together and secure them with some CA glue. Try to not use too much glue because of extra weight.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_c5669idp5zad.jpg"></figure>&nbsp;Glueing the rudder/elevator assembly to the fuselage is the hardest part of the build. It works the best if you put one small drop onto the fuselage and temporary secure it. After that you can check the alignement and adjust it properly.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_sklgvblwtn24.jpg"></figure>If it looks fine, just secure the whole thing with more superglue.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_58pkfcwdk5pu.jpg"></figure>&nbsp;To make the whole thing fly you have to add weight to the nose and adjust the center of gravity. For me a 4,5mm steelball did the trick. You can temporary secure the nose to the rest of the plane with some tape and check it's flight properties.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_9hxutt2kk35r.jpg"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_ui9nlrtydip2.jpg"></figure>&nbsp;For checking the center of gravity you can balance it on two screws. The COG should be at ⅓ of the wing measured from the front.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_vbnmudk1iyhh.jpg"></figure>if it does'nt fly properly you can also try to give it a little bit of lift by bending the elevator up.&nbsp;If it flys, you now can finally glue the nose to the rest of the sailplane.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-11-30_jasr1r5920mo.jpg"></figure>Have Fun!&nbsp;&nbsp;<figure class="table" style="width:92.21%;"><table class="ck-table-resized"><colgroup><col><col><col></colgroup><thead><tr><th colspan="3">If you like this model you may have a look at my other flying toys too</th></tr></thead><tbody><tr><td><figure class="image"><a href="https://makerworld.com/en/models/81500" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-12-03_bc748d83c35e18.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/81500" rel="nofollow noopener">Geared Propeller Launcher</a></td><td><figure class="image"><a href="https://makerworld.com/en/models/76104" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-12-03_eadf473572ad4.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/76104" rel="nofollow noopener">Flying Bat</a></td><td><figure class="image"><a href="https://makerworld.com/en/models/21091" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/231668/2023-12-03_a8fc21a53267c8.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/21091" rel="nofollow noopener">Cross Bow</a></td></tr></tbody></table></figure>

X1C

Planes