binninger.alex

DevonR

<h3>About the tool</h3><p>A simple whetstone knife sharpening aid. Helps when getting started sharpening blades using a whetstone.</p><p>4 Different angles for different types of blades. 14°, 17°, 20°, 25°.<br> </p><h4>Common Sharpening Angles:</h4><p>Pocket Knives- 20°<br>Hunting Knives- 25°<br>Fillet Knives- 17°<br>Tactical Knives- 25°<br>Euro/American Kitchen Knives- 20°<br>Asian Kitchen Knives- 14° or 17°<br> </p><h4>How To Use:</h4><p>The sharpening aid does NOT move with the blade. Place the wedge on one end of your stone and choose the correct angle according to your knife or tools. Lay your knife or tool on it. Then move your knife across the stone maintaining the angle.</p><h4><br>My print settings:<br> </h4><p>0.2mm - Layer Height<br>100% - Infill<br>PLA +</p>

Whetstone Knife Sharpening Aid

Messer 

laisch

<h3>HUGHES MD - 500 (flyable pullcopter) </h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_sman5x65txu7.gif"></figure><p>&nbsp;</p><p>&nbsp;</p><h3>Externals</h3><p>For launching the MD-500, you need to make the “<a target="_blank" href="https://makerworld.com/de/models/81500" rel="nofollow noopener">Overpowered Heli Launcher</a>” before:</p><figure class="image"><a href="https://makerworld.com/de/models/81500" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_cmrmg9lwcdhu.jpg"></a></figure><p>&nbsp;</p><h3>Printingsettings</h3><p>Print as light as possible. I used 2 perimeter, 0.2mm layerheight and 10% infill on the helicopter body.</p><p>For the Rotor use Arachne in the slicer.</p><p>&nbsp;</p><h3>Postprocessing</h3><figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_n770l86x94u8.jpg"></figure><p>Clean the hole for the shaft with an 8mm drill bit. Make it as clean as possible to avoid friction.</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_41bpt3jnpijj.jpg"></figure><p>Add the pins to the body and glue the two haves together with some superglue</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_bb2k67jpmjiq.jpg"></figure><p>Add a drop of superglue into the skid holes and glue the skids in place</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_huhj8w7d9shl.jpg"></figure><p>To make the helicopter fly stable, you have to direct the airflow of the propeller to act as a counterforce against the rotors spinning direction. The easiest way is to make a fin with transparent tape.</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_i9cggf52mewy.jpg"></figure><p>You have to adjust the sice and angle of the tape according to your friction on the shaft</p><p>Testfly -→ adjust → repeat …</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_61dldorkdcxe.jpg"></figure><p>Mount the rotor to the shaft. It should be friction fit, but if its too lose you can add some superglue. (The rotor should spin freely)</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_etlatpk1760y.jpg"></figure><p>To stop the helicopter from rotating during the launch, you have to add the helistops to your launcher. Just remove the old M3x6 screw and replace it with a M3x10.</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_7efl5p749tfj.jpg"></figure><p>Have Fun</p></td></tr></tbody></table></figure><p>&nbsp;</p>

MD-500 (flyable Helicopter)

Spielzeug

fay3dlab

<p>&nbsp;</p><p>I designed this kitcard specifically for an automotive event to sell.. since its been a while the event is over.. i thought i shared it for everyone to 3d print..</p><p>&nbsp;</p><p>Here's the instuctions assembly video..</p><p>&nbsp;</p><figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=U0RY_-SMjKA"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/U0RY_-SMjKA" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure><p><a href="https://www.buymeacoffee.com/fay3dlab" target="_blank"><img src="https://cdn.buymeacoffee.com/buttons/v2/arial-yellow.png" alt="Buy Me A Coffee" style="height: 60px !important;width: 217px !important;" ></a></p>

Lowrider Spider Kitcard

kollegen

carlos_3_d

<p>Silicabox para el Ams de Bambu Lab.</p><p>Cabe en el alojamiento original con su tapa.</p><p>Se debe poner la silica gel en la tapa ventilada (como en la foto) y despues tapar con la otra parte.</p>

Messer

Spielzeug

kollegen

Bambulab X1C