benperk

Maumpfi

Eine Halterung für die Aqara Doorbell G4 (Basisstation)

Aqara Doorbell G4 Halterung Basis

Smart Home

hakStak

A magnet mount designed for the Honeycomb Storage Wall. For use with <a target="_blank" href="https://a.co/d/cSHvLqL" rel="nofollow noopener">60x13.5x5mm magnets</a>, <a target="_blank" href="https://a.co/d/44KHMmO" rel="nofollow noopener">M3 Flathead screws</a>, <a target="_blank" href="https://a.co/d/9WOwFM2" rel="nofollow noopener">and M3x4x5mm inserts</a>. I haven't tested, but the magnets are supposed to hold up to 70 lbs. They are very strong!!

HSW Magnet Mount

larcin

A remix of the Ryobi 4v tool pegboard hanger.&nbsp;Fixed some open geometry that caused infill issues. opened it up to fit the tool better and strengthened the part so the bottom holder will not break off. Added a second model that can be used with the Airpump due to its wider body.

Ryobi 4v Tool Pegboard hanger

Ryobi

Vivien L.

Made this based of Apple's modern take on the "Hello" logo in recent versions of macOS screensavers and as seen in Keynotes.

Apple Modern Hello

Apple

KG3Dee

Heavily inspired by <a target="_blank" href="https://makerworld.com/en/models/35897#profileId-33596." rel="nofollow noopener">https://makerworld.com/en/models/35897#profileId-33596.</a>A little higher in front for added support, as well as deeper end stop grooves.All edges chamfered for easy insertion. Staggered by 35 degrees.Ø5mm countersunk mounting holes.

Standing or Wall Mounted Build Plate Holder

Printer Add Ons

JamesThePrinter

This is a Christmas tree designed in a flat pack style. All three sections of the tree slide together and get topped by the star. All sections are printed with no bottom or top layers. This allows the infill to be the the main pattern across the tree. The tree shown has a 50% triangle infill, but many others would look good as well.Other ideas:<ul><li>No infill, just perimeters for hollow pieces</li><li>Use top/bottom layers normally</li><li>Lower infill percentages, but with infill line width multipliers</li></ul>Check out the rest of my Christmas models <a target="_blank" href="https://makerworld.com/en/u/1360890085/collections/69417" rel="nofollow noopener">here</a>!&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>

Christmas Tree - Flat Pack Style

Holidays

gsingh2011

A remix of <a target="_blank" href="https://www.printables.com/model/485526-gridfinity-magnetic-baseplate-jig-print-in-place" rel="nofollow noopener">schneems design</a>. This is for installing magnets into baseplates, for installing magnets into bins see <a target="_blank" href="https://makerworld.com/en/models/45220" rel="nofollow noopener">this project</a> instead.&nbsp;Two problems I ran into with the original design were glue getting on the jig separator where the magnets are placed and accidentally rocking/tilting the jig when lifting up the magnet part.&nbsp;This remix replaces the four cylindrical locations where the magnets are placed with some small “bumps”, which reduces the likelihood of glue getting on them, and even if glue does get on them it's less likely to cause any problems because of the reduced surface area.&nbsp;The second change is that there are some small stabilizers added to the outer rim of the jig. When lifting up the magnet part of the jig, your fingers are usually holding the other part down by its edges. These stabilizers prevent the jig rocking while your fingers are pressing on those edges, which could cause problems with magnets coming out of the baseplate holes.&nbsp;The magnetic part of the jig is unchanged, and I've uploaded the original file for that unchanged.&nbsp;The Fusion 360 file is included if you'd like to make any changes.

Smart Home

HSW

Ryobi

Apple

Printer Add Ons

Holidays

Organization