artpassion

recycle

Renba

Fader knob replacement for Yamaha TF5 Mixer and many more…Fit also fader 1.2 with x4 lenght x5mm height&nbsp;Printed horizontaly give a better finish but supports will be more difficult to remove.

Yamaha TF5 Fader

Audio

Ashmotif200

garageCube 3D model License Agreement Copyright ©2019, garageCube hardware Sàrl 43 route des Acacias 1227 Carouge, Switzerland www.garagecube.com All rights reserved.&nbsp;Use this 3d model built(including3D print)Â with or without modification for structure assembly in commercial and non-commercial project is permitted for legal purpose.Â &nbsp;Reselling the source file and/or the built 3d model with or without modification is not permitted without the authorization of garageCube hardware Sàrl.&nbsp;Redistribution of the source file and/or the built 3d model with or without modification for non-commercial purpose are permitted provided the copyright notice, this list of conditions and the following disclaimer.&nbsp;THIS 3D MODEL IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS"ASIS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES(INCLUDING,BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT(INCLUDINGNEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS 3D MODEL, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

garageCube Cube

Bambu Lab

This is an official component set by Bambu Lab for the A1 printer. The AMS lite Top Mount setup is a tested solution for mounting the AMS lite on top of the A1 printer.&nbsp;The component set consists of two main modules:<ol><li>Top Mount Bracket</li><li>Z-Axis Stiffener</li></ol>The Top Mount Bracket is meticulously designed to be tilted to the front for better balance. Additionally, the upper half of the bracket can spin left and right, providing easier access to the back spools.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000092486/design/2023-12-14_ceeb9c0ed0a76.jpeg"></figure>&nbsp;The Z-axis Stiffener is designed to dampen back-and-forth printer movements. Thanks to the special elastic damper design at the bottom, there is minimum wobble even when printing in ludicrous speed with AMS lite fully loaded.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000092486/design/2024-04-23_cafcdb16e7224.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000092486/design/2024-04-23_4980ec2ffcf67.jpg"></figure>&nbsp;AssemblyHere is a tutorial video for the installation:<figure class="media"><div data-oembed-url="https://youtu.be/RmZOgrcDiRQ"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/RmZOgrcDiRQ" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;You can also buy the required hardware as a kit from here:<a target="_blank" href="http://store.bambulab.com/products/ams-lite-top-mount-screws-kit" rel="nofollow noopener">http://store.bambulab.com/products/ams-lite-top-mount-screws-kit</a>&nbsp;&nbsp;&nbsp;&nbsp;

recycle

Audio

Ash

Accessoires Imprimante