ARTICUL8

Jaxel

I was looking for a way to stack multiple AMS on top of each other. There were several systems here on MakerWorld, but there were a few problems with them that I didn't like. Most importantly is that they weren't actually “stacking” systems. They let you put one AMS on top of another, but they could not stack beyond that. You could not stack a third, or even a fourth AMS in a single column. So I decided to make my own completely modular system that allows you to stack as many AMS you want!&nbsp;This system is sectioned off into 124mm “blocks”. There are two included wall heights, a “1-block” and a “2-block” wall. This allows you to raise your AMS to any height you want, at multiples of 124mm. If you want to simply put one AMS on top of another, you could print out walls in 3-blocks of height (2+1). This will allow enough space for you to slide the bottom AMS out in order to change filaments (like other AMS stacking systems). However, if wanted to be able to open the bottom AMS lid without having to slide it out, you would print out walls in 4-blocks (2+2) of height. Even more customizable, if you have under-AMS drawer systems, and you needed even more height between your AMS, you could print additional blocks of height to raise the top AMS even more!&nbsp;The “arms” that hold up the AMS are completely modular, and can be attached and removed at will. This has the advantage of being able to change arms without having to reprint your entire walls. So if your AMS breaks, and you buy a new one, and it turns out there is yet another new revision of the AMS, you can simply print out new arms that match the revision.&nbsp;<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=tUU1KRgZpPQ"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/tUU1KRgZpPQ" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;I have designed this model to be as easy and simple to print, with as little support material as possible. The included print profile has parts oriented in specific ways to minimize the chance of breakage due to lateral force, so part tension does not split at layer lines. There are several pre-defined plates:<ul><li>Plate 1:<ul><li>2x 2-block wall<ul><li>These models have support enforcers on the arm sockets.</li></ul></li></ul></li><li>Plate 2:<ul><li>2x 1-block wall<ul><li>These models have support enforcers on the arm sockets.</li></ul></li></ul></li><li>Plate 3:<ul><li>2x Rear Bracers<ul><li>Optional: if you want to have some extra rigidity to your stack to prevent “wobble”.</li><li>This system uses the AMS as a bracer. You want at least two sets of bracers on your stack.</li></ul></li><li>4x Dovetail Biscuits<ul><li>Connect the bracers to the rear of the walls.</li></ul></li><li>1x AMS (rear) Bracket<ul><li>This connects the AMS to a rear bracer, if you decided to print one.</li><li>This model is oriented at a 45 degree angle for strength.</li></ul></li><li>1x AMS (rear) Bracket Lock<ul><li>Locks the rear bracket in place so the middle pin doesn't shift.</li></ul></li></ul></li><li>Plate 4:<ul><li>2x AMS (side) Bracket<ul><li>These connect the AMS to the side walls through arm sockets.</li><li>These models are oriented at a 45 degree angle for strength.</li><li>Print these out in sets of two, one for each side of the AMS.</li></ul></li></ul></li><li>Plate 5:<ul><li>2x 2-block Blank<ul><li>Purely cosmetic, so things look nicer when you have rear bracers.</li><li>If you don't use rear bracers, then you don't need these blanks.</li></ul></li><li>8x Dovetail Biscuits<ul><li>Connect the blanks to the rear of the walls.</li></ul></li></ul></li><li>Plate 6:<ul><li>2x 1-block Blank<ul><li>Purely cosmetic, so things look nicer when you have rear bracers.</li><li>If you don't use rear bracers, then you don't need these blanks.</li></ul></li><li>4x Dovetail Biscuits<ul><li>Connect the blanks to the rear of the walls.</li></ul></li></ul></li><li>Plate 7:<ul><li>1x Blank (rear) Bracket<ul><li>A connector to attach both ends of a bracer if you printed a rear bracer without an AMS.</li><li>This model is oriented at a 45 degree angle for strength.</li></ul></li><li>4x Connector - Dowel<ul><li>Optional to keep your walls together when you stack them.</li></ul></li></ul></li></ul>I have included some additional STLs that you can peruse at your leisure, but they are not on plates.&nbsp;You can find other models I have released for the X1C/AMS here:<a target="_blank" href="https://makerworld.com/en/u/2811301167/collections/109412" rel="nofollow noopener">https://makerworld.com/en/u/2811301167/collections/109412</a>&nbsp;If you appreciate my models, please consider <a target="_blank" href="https://ko-fi.com/ultrajaxel" rel="nofollow noopener">buying me a coffee</a>!

AMS Stacking System

Printer Addons

We Be Printin'

<a target="_blank" href="https://makerworld.com/en/models/513662#profileId-429788" rel="nofollow noopener">GoPro screw model here.</a>&nbsp;This 3D model represents a versatile and modular ground/sand spike designed to securely mount a GoPro camera for various outdoor activities. The system is composed of three main components: the mount, the spike, and multiple extensions, all designed to be easily assembled and disassembled for convenient transport and adaptability. The extensions can also be used as simple handles. &nbsp;The mount is specifically designed to fit GoPro cameras securely. It features a standard GoPro mounting and a threaded side to mount to the rest of the kit, allowing for easy attachment and detachment of the camera. The spike is designed to be driven into various types of terrain, including sand, dirt, and grass. It has a pointed end for easy insertion and a reinforced structure to withstand outdoor conditions. It includes a threaded top to connect with the mount or extensions securely.&nbsp;The extensions are cylindrical rods that can be connected to increase the height of the mount. Each extension has threaded ends for seamless attachment. The extensions come in various lengths to offer flexibility in mounting height. Can also be connected together to achieve even bigger height.&nbsp;The modular design allows for quick assembly and disassembly. Users can connect the mount directly to the spike for a low-profile setup or add one or more extensions between the spike and mount to achieve the desired height. The threaded connections ensure a secure and stable setup, even in windy conditions.&nbsp;This modular GoPro ground/sand spike is perfect for a range of outdoor activities including beach trips, hiking, camping, and any other scenario where a stable camera mount is needed on uneven or soft ground. Its portability and flexibility make it an essential accessory for capturing steady and dynamic footage in various environments.&nbsp;&nbsp;

Modular GoPro Sand Spike Kit - Handle + Extensions

INSTA360

3D Print Bros

<a target="_blank" href="https://www.tiktok.com/@brady_meets_world" rel="nofollow noopener">@bradyprints on Tiktok</a> challenged the 3D printing community to print the popular <a target="_blank" href="https://makerworld.com/en/models/245471#profileId-261872" rel="nofollow noopener">Gyro Fidget Spinner</a> as big as they can, but I couldn&#39;t help but notice there is one glaring issue - as you scale up the model, the tolerances between the spinning rings also scale up, resulting in a wobbly spinner.&nbsp;To combat this, I redesigned it with updated tolerances for a smooth spinning experience. This model is 300% scale of the <a target="_blank" href="https://makerworld.com/en/models/245471#profileId-261872" rel="nofollow noopener">original</a>! This behemoth spinner is a true statement piece. Perfect for any coffee table and a great conversation starter. Even looks awesome hung on the wall! Not to mention it&#39;s strangely addicting to spin.&nbsp;&nbsp;<a target="_blank" href="https://cults3d.com/en/3d-model/game/commercial-license-jumbo-gyro-fidget-spinner-v2" rel="nofollow noopener">Onetime payment commercial license available on Cults3D here!</a>  Don&#39;t forget to print the pocket-sized version for fidgeting on-the-go here:&nbsp;<a target="_blank" href="https://makerworld.com/en/models/245471#profileId-261872" rel="nofollow noopener">Gyro Fidget Spinner V2 by 3DPrintBros - MakerWorld</a> &nbsp;And if that&#39;s still too big for you, check out the Micro Gyro:&nbsp;<a target="_blank" href="https://makerworld.com/en/models/435704#profileId-340795" rel="nofollow noopener">Micro Gyro Fidget Spinner by 3D Print Bros - MakerWorld</a><figure class="image image_resized" style="width:34.82%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000393051/design/2024-04-19_e3cf893471adc.gif"></figure>— &nbsp;&nbsp;Now that you&#39;ve printed this glorious piece, put it on display with the perfect stand designed by Stickler:  <a target="_blank" href="https://makerworld.com/en/models/423233#profileId-326399" rel="nofollow noopener">Display Stand - Jumbo Gyro Fidget Spinner by Stickler - MakerWorld</a><figure class="image image_resized" style="width:62.09%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000393051/design/2024-04-11_9520a9b47d052.jpg"></figure>

Jumbo Gyro Fidget Spinner

PURGE FILES

HangarDesigns

<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/571293/2023-12-28_a777d9d3d67ba.png"></figure>&nbsp;Oklahoma of University Sooners floating logo sign. THIS IS A MULTI-PART LOGO, that means it does not require an AMS! This type of design has three benefits-&nbsp;<ol><li>No AMS/Multi Material system is required to print any of my signs.</li><li>All forward facing parts can be printed face down, allowing the texture of the build plate to be visible.</li><li>These are designed with different layers at different heights, so you get a unique 3 dimensional look.</li></ol>&nbsp;Most components should be able to be assembled using the tight tolerances only of the press fit pins and sockets, however there may be some small pieces (logo dependent) that might require manual placement and/or CA glue. ProTip- if CA glue cures without an accelerator, it may leave a smoky residue. If you apply a thin coat of WD-40 and wipe away, this residue will disappear.&nbsp;&nbsp;The base is modeled with an integrated sawtooth hanger with standoff feet as well as a hinged kickstand. This allows any of the signs to be wall mounted or placed on a desk/shelf.&nbsp;&nbsp;The large holes in the logo and base are designed to accept TPU adapters. The purpose of these adapters is to accept ⅜” (10mm) acrylic rods with slight manufacturing diameter deviations. This allows the acrylic rods to be installed and removed easily, while remaining secure. The inserts are designed with a 2 degree draft angle to lock them in place once installed (see assembly render below). I generally print these in clear TPU or a matching color TPU if I have it.&nbsp;<ul><li>The TPU adapters can be found here- <a target="_blank" href="https://makerworld.com/en/models/39229#profileId-38178" rel="nofollow noopener">https://makerworld.com/en/models/39229#profileId-38178</a> .</li><li>The acrylic dowels I use can be found here- <a target="_blank" href="https://www.amazon.com/dp/B09SKYYS5X?psc=1&ref=ppx_yo2ov_dt_b_product_details." rel="nofollow noopener">https://www.amazon.com/dp/B09SKYYS5X?psc=1&ref=ppx_yo2ov_dt_b_product_details.</a></li><li>If you prefer to forgo the TPU adapter and acrylic rods, I have designed 3D printable rods here- <a target="_blank" href="https://makerworld.com/en/models/112446#profileId-120394" rel="nofollow noopener">https://makerworld.com/en/models/112446#profileId-120394</a></li></ul>&nbsp;If you'd like to see the rest of my floating logo designs, please check out my collections!&nbsp;NFL- <a target="_blank" href="https://makerworld.com/en/u/838667549/collections/49157" rel="nofollow noopener">https://makerworld.com/en/u/838667549/collections/49157</a>&nbsp;MLB- <a target="_blank" href="https://makerworld.com/en/u/838667549/collections/49162" rel="nofollow noopener">https://makerworld.com/en/u/838667549/collections/49162</a>&nbsp;NCAA- <a target="_blank" href="https://makerworld.com/en/u/838667549/collections/57027" rel="nofollow noopener">https://makerworld.com/en/u/838667549/collections/57027</a>&nbsp;NBA- <a target="_blank" href="https://makerworld.com/en/u/838667549/collections/57026" rel="nofollow noopener">https://makerworld.com/en/u/838667549/collections/57026</a>&nbsp;NHL- <a target="_blank" href="https://makerworld.com/en/u/838667549/collections/49163" rel="nofollow noopener">https://makerworld.com/en/u/838667549/collections/49163</a>&nbsp;&nbsp;&nbsp;If you like this design, donations are appreciated- it helps me buy more filament to flesh out my designs. I accept venmo, cashapp, or apple cash- Message me on MakerWorld if you’d like to donate or request a commission.

Printer Addons

INSTA360

PURGE FILES

UNIVERSITY