antho77m

Litolunar

Litofania redonda impresa en 3d. Como se ve es una litografía redonda de Harry Potter.Es necesario comprar una luz para enroscarla debajo: <a target="_blank" href="https://a.aliexpress.com/_EICbz19" rel="nofollow noopener">https://a.aliexpress.com/_EICbz19</a>Se compone de dos piezas, una de ellas se pega al producto de arriba, y la otra se enrosca. El modelo está muy logrado, ya que si se funde el led, es muy fácil de cambiar.&nbsp;Relleno 100%. Calidad 0.16. Adherencia de impresión: Borde Sin soportes.

Litofania de Harry Potter

lithophane

modélisme 

3Dolphin

A simple hose adapter for the XTool S1 laser, which replaces the original hose adapter.It is suitable for a 100mm hose.

XTool S1 Hose Adapter for 100mm Hose

Xtool

Wojciech Kawa

<h2>The front of the extruder as a PCB.</h2>I tested several color variants and it turned out that the path and the background must have a high contrast so that the paths can be seen best. In my case, the best colors were matte black as the background and gold as the paths. There are of course two versions for the A1 mini and A1. there are two versions of the rotating center in the project (I couldn't decide which one is better - you decide)<h4>Before you start printing, make sure you have a clean plate (Wash it in warm soapy water or IPA). The first layer has a lot of small elements that must stick well to the plate.</h4>&nbsp;If you have printed it, please leave a rating.&nbsp;Before installation, the original front and the rotating element must be dismantled. During installation, the eye should be pressed as far as it will go. After putting the face, the eye should be flush with the face or deeper. When assembling, make sure that the top latches are flush with the top edge before pressing from the front.&nbsp;&nbsp;<figure class="image"><a href="https://www.buymeacoffee.com/wojciechkawa" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/509575/2024-01-30_46d010488f47e.webp"></a></figure>&nbsp;<a target="_blank" href="https://makerworld.com/it/u/3316073328" rel="nofollow noopener">See my other projects.</a>&nbsp;Assembly instructions below.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/509575/2023-12-19_a1ede8a515cf8.jpg"></figure>

A1 mini & A1 PCB Face

A1 mini upgrades

vandragon_de

This simple boat is quite uncomplicated to print and is fun with or without the motor.&nbsp;Due to the appropriate size and the relatively low weight, however, it accommodates the wind-up motor and this therefore has sufficient thrust.&nbsp;However, if the boat is too empty for you, you can simply print the <a target="_blank" href="https://makerworld.com/en/models/183765#profileId-202627" rel="nofollow noopener">EASY 13 Printable Jointed Figure</a>, as I did as an example, and add an absolutely ingenious moving passenger as an option. I have also created a very simple alternative rear bench where you can clamp this figure.&nbsp;I hope you have a lot of fun. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/547576/2024-02-17_1d1bdbee3b346.gif"></figure>

Simple Boat for Wind-up motor

Kits Bambu Lab

Dual Words&nbsp;Combine two words into one model. The model will auto pad with heart shaped filler character if the words are mismatched in length.

Dual Words

Prenoms...

NakedPlate

Muhammad Ali (HueForge) 

hueforge

bambaxp

Bambu lab x1c upper air opening, only for x1c

x1c upper air opening

X1carbon upgrades

Tommy 3D Lab

<h2>POCKET GUN 4.0  </h2>The Pocket Gun 4.0 is a rubber band pistol designed specifically for maximum portability and functionality. With a collapsible handle and compact dimensions, it is ideal for the pocket while still offering some features.  DIMENSIONS (collapsed):  Length: 103.5 mm Width: 65 mm Thickness: 16.6 mm FEATURES:  Collapsible handle: The handle can be collapsed, making the pistol extremely compact and easily storable. This is an outstanding feature that sets it apart from other rubber band pistols, maximizing its suitability for the pocket.  Bit holder: Bits can be inserted into the muzzle of the pistol. While this is more of a playful feature and the holder may not be perfect for frequent use, this idea holds the potential to expand the Pocket Gun 4.0 into a versatile multitool. In emergencies, this function can still be useful.  Measurement unit on the handle: A 3 cm long measurement unit is located on the handle, which can be used as a ruler or for measuring small objects. This handy feature enhances the usefulness of the pistol in everyday life.  Ammunition: The Pocket Gun 4.0 uses rubber bands approximately 3 cm in length.  PERFORMANCE:  Power: Due to its compact size, the Pocket Gun 4.0 is not the most powerful model on the market. However, it offers sufficient power for typical rubber band pistol applications and excels in its unique portability and multifunctionality.&nbsp;&nbsp;&nbsp;Print profile: I will provide 2 profiles for the model, one with AMS and one without. Primarily in the AMS variant, it concerns support with PLA in conjunction with PETG, which detaches extremely easily and cleanly. The AMS variant is definitely the better choice as certain elements come out of the printer very cleanly. Additionally, it&#39;s a very interesting solution to ensure clean bridging, but unfortunately, AMS is required. If you prefer not to print with PLA and PETG as support, switch to the profile (without AMS).  Montage: Assembly of the Pocket Gun 4.0 is mostly done through snap connections, although some points need to be fixed with super glue. An assembly video has been provided, illustrating the key steps and enabling easy assembly.The magnet that can be inserted is optional.  <figure class="media"><oembed url="https://www.youtube.com/watch?v=vrfysUGJKbg"></oembed></figure>  Potential for improvement: While the Pocket Gun 4.0 is a thoughtful and versatile model, it still has some minor issues that could further enhance its performance and durability: Spring wear: The spring in the locking mechanism wears relatively quickly and fails to fully drive the lock into the optimal position. To solve this issue, the spring would need to be printed from ABS, which is currently not possible for me as I lack the enclosed build space. Although the PETG spring does not last long, the locking function still continues to work.  Bit holder: The bit holder is not deep enough, which can affect the secure storage and use of the bits.  Material tests: During test prints with various filaments such as PLA, PLA+, PETG, some important insights were gained. PLA+ proved to be the least suitable, encountering issues such as warping and poorer dimensional accuracy. Even using PLA+ for the springs led to disappointments due to rapid wear. Similarly, the PLA SILK Bronze from Bambu, while aesthetically pleasing, quickly broke some parts. It may be suitable for decorative purposes but not for functional models.  The best results were achieved when the grip and springs were printed from PETG and the rest from PLA. However, it is possible to print everything from PETG, with the main reason for the combination of materials being to save time and material.  Despite these challenges, the Pocket Gun 4.0 remains a practical and portable rubber band pistol that can be made even better through continuous improvements.  Recommended materials:  PLA: Bambu code : 10101 Kingroon : <a target="_blank" href="https://amzn.to/4agNkvO" rel="nofollow noopener">https://amzn.to/4agNkvO</a>Sunlu : <a target="_blank" href="https://amzn.to/4bhXnlr" rel="nofollow noopener">https://amzn.to/4bhXnlr</a> PETG: Bambu code : 30600 Amazone : <a target="_blank" href="https://amzn.to/3WN2khR" rel="nofollow noopener">https://amzn.to/3WN2khR</a>&nbsp;&nbsp;Explore my tools:  <ul><li>Caliper: <a target="_blank" href="https://amzn.to/3wduBU8" rel="nofollow noopener">Amazon Link</a></li><li>Tool Kit: <a target="_blank" href="https://amzn.to/4brZsuV" rel="nofollow noopener">Amazon Link</a></li><li>Soldering Mat: <a target="_blank" href="https://amzn.to/4a47etW" rel="nofollow noopener">Amazon Link</a></li><li>Cutting Mat Set: <a target="_blank" href="https://amzn.to/3WwqEUZ" rel="nofollow noopener">Amazon Link</a></li><li>Disposable Gloves: <a target="_blank" href="https://amzn.to/3y5rU7n" rel="nofollow noopener">Amazon Link</a></li><li>4L Storage Containers 6 Set: <a target="_blank" href="https://amzn.to/4a7ZeIs" rel="nofollow noopener">Amazon Link</a></li><li>spring clamps - <a target="_blank" href="https://amzn.to/3wJrfbG" rel="nofollow noopener">Amazon link</a>.  </li><li>Graphics Tablet with Display: <a target="_blank" href="https://amzn.to/3VlWsuW" rel="nofollow noopener">Amazon Link</a></li><li>Graphics Tablet: <a target="_blank" href="https://amzn.to/3X4UDDJ" rel="nofollow noopener">Amazon Link</a> Check out my video on YouTube and witness how I created the PocketGun 4.0 using Fusion 360! Click the link below to watch it now, and subscribe for more exciting content!  </li></ul><figure class="media"><oembed url="https://www.youtube.com/watch?v=w9y4KveSfFE&amp;t=3s"></oembed></figure> I would appreciate a positive review, but also welcome constructive feedback. And don&#39;t forget to subscribe to stay updated. Thank you! Notice This print serves as an indicator of whether your printer is operating cleanly and properly. If so, the product will function smoothly as demonstrated in the video. Otherwise, you&#39;ll recognize that your printer isn&#39;t printing properly. You can then address the specific issues to elevate your printer&#39;s performance and the quality of its results to the next level. If any issues arise, I&#39;m here to help.

Pocket Gun 4.0

tir repliques

disinterest

UPDATE 01-23: Added gantry stabilizers that go underneath the lead screws per request from <a target="_blank" href="https://makerworld.com/en/u/3167095382" rel="nofollow noopener">@loafer_coyote0b</a>. Thanks again!I printed without supports since its a small gap to bridge, but the hard rubber pad on the underside of the gantry should slot into it, purge bins that sit up close to the printer shouldn't have any issues. It really does help with support since the bed is set down on the gantry then attached with screws from beneath, a major oversight on the original design on my part. &nbsp;I do not use bambu studio so I have not uploaded a print profile, only the raw files and a presorted plate. If someone would be so kind as to take on that task it would be very much appreciated.&nbsp;Print 2x of A1ScrewStablizerBody in a material of your choice.Print 2x of A1ScrewStablizerPad in TPU.&nbsp;ORIGINAL:&nbsp;I did not like any of the feet currently floating around and the ones I did required extra stuff like squish balls. So I taught myself what I needed for fusion 360 and stayed up too late a couple nights to make this.&nbsp;The tpu top pad piece slots perfectly into the screw holes on the underside corners of the machine, tpu feet sit in the bottom, you can print the body out of whatever, I chose abs as I plan on making a fan shroud to actively cool the internals so it can be enclosed, but I test printed multiple iterations in pla and petg with both holding the weight fine.&nbsp;Note: The walls and really any plastic part of the feet should not touch the printer, I deliberately left a gap so there isnt any vibration noises and only the tpu pad makes contact.&nbsp;&nbsp;&nbsp;Print Requirements&nbsp;NEED SUPPORTS on the Front/Rear pieces (I did normal auto, snug, build plate only) rotate the Foot with filet up or down depending on which side you want to contact the table surface.&nbsp;4 x Foot2 x Front2 x Rear (IMPORTANT) Mirror ONE to fit other side, it will work fine otherwise but for aesthetics flip it.2 x PadFront2 x PadRear Alternately use the presorted plates which are separated by material.No specific slicer settings other than supports so use what you're comfortable with.

A1 Riser Anti Vibration / Noise Reduction Feet

A1 Upgrade

Deltaprints

Nordic circular hollow vase. Vase with removable tube. Both parts can be printed without supports.&nbsp;

Circular Hollow Vase - Nordic Circular Design

objets décoration 

JamesThePrinter

Take chess with you wherever you go with this MakerWorld exclusive!<figure class="image image_resized" style="width:31.46%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000443923/design/2024-04-26_e80da61064c23.gif"></figure>This travel chess set includes all of your chess pieces, a board and storage area. Because the chess pieces are small and detailed, a small nozzle is required for the chess pieces!As a bonus, I have also included checkers in this set.<figure class="image image_resized" style="width:31.1%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000443923/design/2024-04-26_dfa599f3ea1ca.jpg"></figure><h3>Print Settings</h3><ul><li>Chess Pieces<ul><li>0.2mm nozzle required</li><li>designed to use 0.1mm layer height</li></ul></li><li>Checkers<ul><li>0.2mm nozzle recommended, but not required</li></ul></li><li>Board &amp; Case<ul><li>Nozzle size doesn&#39;t matter - I included print profiles for 0.2mm and 0.4mm nozzle sizes<ul><li>0.2mm nozzle - Allows you to keep the same nozzle installed, but the prints take longer</li><li>0.4mm nozzle - Forces a nozzle change, but drastically lowers print time</li></ul></li></ul></li></ul>&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;&nbsp;The following filaments were used in the pictures above:<ul><li>Bambu Lab Matte Dark Brown PLA</li><li>Bambu Lab Matte Brown Latte PLA</li><li>Bambu Lab Matte Charcoal PLA</li><li>Bambu Lab Basic Ivory White PLA</li><li>Bambu Lab Matte Scarlet Red PLA</li></ul>

Travel Chess Set

jeux

The Spirit

Made a nice soda can holder in voronoi style.The soda can fits snug, so it does not slip out.Can be printed without supports.With the small hole at the bottom you can easily push out the empty can.A cool gadget for every party.Hope you like it.&nbsp;2024-02-28:added two more print profiles:<ul><li>add the A1 mini to the supported printers</li><li>add the A1 mini to the supported printers + add support</li></ul>2024-03-08:made a new version for the smaller and taller soda cans:<a target="_blank" href="https://makerworld.com/en/models/238092#profileId-254012" rel="nofollow noopener">https://makerworld.com/en/models/238092#profileId-254012</a>

Voronoi soda can holder

cuisine 

matt thibs

I used a marble PLA for the white background.&nbsp;Instructions to edit text:<ol><li>Rotate plate to view from underneath.</li><li>Click on “Objects” tab under the Filament selection.</li><li>Right click on “company text”, “name text”, “info text”, and edit the text, font, and size. Note that this was created using the PC version of Bambu Studio so the text might be different on a Mac. Simply change the font type to your choosing.  </li><li>Click “Slice Plate”.</li><li>Warning Verify that the text and the picture frame are both on the first layer. If not, move the picture frame down to the first layer or start the process over. Sometimes during the manipulation of the text, the bodies move slightly. Do not print unless everything is flush on first layer!</li><li>For best text results, verify that the color of the card prints before the color of the text. Click the hexagon settings button on the plate to verify the first layer sequence.</li><li>Important, let the bed completely cool before pulling off the frame and the back lid to prevent warping!</li></ol>

Personalized Business Card Flush Surface 

Bureautique

PenolopyBulnick

These faceted diamond cut out were designed to work with multi-colored filaments. The pair need to be oriented on the bed so they are facing opposite directions if you want to get teh full effect of the different colors. &nbsp;I also found they look nice with a fuzzy skin so I recommend giving that a try.

Pyramid Faceted Earrings - Smooth or Fuzzy Skin

bijoux 

HpInvent

The Phone Pillow: Crafted to resemble a cozy cushion, this unique accessory is actually made from durable plastic. Its plush design provides a comfortable resting place for your device, seamlessly blending functionality with style.&nbsp;It&#39;s comfortably sized for an Iphone 15pro Max or similar size. If you have a smaller phone you can downsize the model to reduce print time ;) Because of many requests I added a version with a cable slot for the charging cable to the print profiles.&nbsp;Due to many requests for commercial licenses for my 3D models I created a patreon page. You can become a member to get permission for commercial use or just want to support my work : <a target="_blank" href="https://www.patreon.com/user?u=79128277" rel="nofollow noopener">https://www.patreon.com/user?u=79128277</a>  There you can also find exclusive Models for Patreon Subscribers only ;) If you Just want to give a one time Support you can buy me a coffe here ;)  <a target="_blank" href="https://buymeacoffee.com/hpinvent" rel="nofollow noopener">https://buymeacoffee.com/hpinvent</a>&nbsp;Here is a small Sneak Peak of a coming Bathroom Set  More Information about the launch date and early acces can be found on my Patreon. <a target="_blank" href="https://www.patreon.com/user?u=79128277" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465699/design/2024-06-14_835436fae26ee.png"></a><a target="_blank" href="https://www.patreon.com/user?u=79128277" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465699/design/2024-05-28_f3fb110d8cdec.png"></a> <a target="_blank" href="https://www.patreon.com/user?u=79128277" rel="nofollow noopener"><img class="image_resized" style="width: 61.65%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465699/design/2024-05-30_38b5963246ece.png"></a>Also check out my other Designs!I have a bunch more stuff in my profile!! <a target="_blank" href="https://makerworld.com/en/u/3624704578" rel="nofollow noopener">https://makerworld.com/en/u/3624704578</a><a target="_blank" href="https://makerworld.com/en/models/428498" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465699/design/2024-04-18_7588ba5642a27.png"></a><a target="_blank" href="https://makerworld.com/en/models/426994" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465699/design/2024-04-15_b0f8912a15393.png"></a><a target="_blank" href="https://makerworld.com/en/models/427979" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465699/design/2024-04-15_b1e75bac7bd51.png"></a><a target="_blank" href="https://makerworld.com/en/models/416941" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465699/design/2024-04-08_ebe2de8bae1b3.png"></a><a target="_blank" href="https://makerworld.com/en/models/232706" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465699/design/2024-03-06_ea517b7dbe741.png"></a><a target="_blank" href="https://makerworld.com/en/models/394559" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465699/design/2024-03-27_3b061a50c97b7.png"></a> <a target="_blank" href="https://makerworld.com/en/u/3624704578" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000465699/design/2024-03-08_a8a626fc04c78.png"></a>  &nbsp;&nbsp;&nbsp;Happy printing!&nbsp;

The Phone Pillow

accessoires téléphones 

Ary Young

A second creation based on the original author&#39;s modelThe original cutter model has been changed into a comb model, which is more friendly to children

OTF Fidget Comb

fidgets/ obj.roulements…

3DCrabClawCreations

A quick Barbie lamp that I made for a friend. Easy to print and just needs any LED light strip inside. &nbsp;

Barbie Lamp

enseignes/ obj.lumineux

impietro

This is my fidget flower, just flip it over to rotate the flower along its spiral stem, a real stress reliever. Also printable in color, nice game to have in hand. It doesn't need any special print settings, you print it turns. The motto is: you flip, he turns. It can be printed in full color using the ams system. The model consists of 3 parts: the flower stem, the flower and the top cap. Insert the flower into the stem without forcing, it will slide on its own as there is a great tolerance and there is no friction, then screw on the top cap. The fidget flower is now ready. I printed it in color using my ams and colored pla filaments, I used a bit of brim for the adhesion, and I inserted the tree supports for the flower print because there are suspended petals. I recommend using the addactive layers for the flower so it comes out smooth and neat. If you like my model, leave me a like to let me understand. If you print it I'll wait for your review with image so I can see your creativity in coloring it.

fidget flower

Fleurs/nature

Makerspace.Online

For this to work you have to download the casing from my <a target="_blank" href="https://makerworld.com/en/models/148536" rel="nofollow noopener">Business card Embosser (LINK!)</a> As many requested, the CAT Rollers for the Business card embosser! More rollers will be added in the furure! Keep an eye on my page or follow my instagram! Note: This design is licensed under a <a target="_blank" href="https://creativecommons.org/licenses/by-nc-sa/4.0/" rel="nofollow noopener">Creative Commons Attribution-Noncommercial-Share Alike</a> Please do not sell this file or printed product.

CAT PATTERN -  Business Card Embosser

gaufrage 

Bootjevaarder

KeyRing of a combustion boxer-engine with turning crankshaft and moving pistons. In this design the pistons of each opposed pair of cylinders move inwards and outwards at the same time. Like all BMW boxer engines. Printing No supports. I printed with PLA+, layer height 0.15 mm. Assembly - Use some oil or grease between moving parts for a smooth operation. - Build the crankshaft using the crankshaft alignment tool. Apply glue. I use Loctite Super Glue-3 Power Gel. Attention for the orientation of the piston rods: upper piston rod upside down! <img class="image_resized" style="width: 357px" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000472676/design/a688f663-b8e5-49a7-bb4b-b3fb8920afee.webp">- Click the pistons in the cylinders, placing the assembled crankshaft in the crankcase. <img class="image_resized" style="width: 357px" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000472676/design/535eb941-b7f9-406b-bafa-4ab4e1cc23a6.webp"> - Screw the winding button on the back of the crankshaft. Operation Turn the winding button on the backside of the crankcase. The pistons of each opposed pair of cylinders move inwards and outwards at the same time.

Boxer-Engine KeyRing

pendentifs / porte clés

vit.budina

This Print-in-Place model of the famous Japanese offroader Suzuki Jimny is my second Print-in-Place vehicle with working suspension! The wheels spin too!&nbsp;The only thing you have to do after printing is to snip off a few tiny pillars that prevent the axle casings from fusing with the wheel axles during printing and you are off to traverse the wilderness!&nbsp;If you wish to scale it down, I wouldn't go below 60% since the supporting bits at that scale are thinner than the nozzle can print. There are two versions: a normal one and one with weaker springs. The one with weakened springs is intended for scaled-up versions, where the springs can get pretty stiff quite quickly.&nbsp;Despite the limitations of designing a vehicle with interior and working suspension and wheel mechanisms, I was able to preserve all the differentiating and iconic features of the vehicle. Some long bridges could become a problem if you decide to scale the model up, but otherwise, it's a pretty easy model to print. However, if you have issues printing any of my designs, DM me on Instagram (https://www.instagram.com/vit.budina/) and I will send you my Cura profile.&nbsp;Enjoy! :D&nbsp;Caution: Sharp Edges - Not suitable for children under 9 years due to breakable plastic. Adult supervision required.

Print in Place Suzuki Jimny

vehicules

*Find the feminine version here: <a target="_blank" href="https://makerworld.com/en/models/63634" rel="nofollow noopener">https://makerworld.com/en/models/63634</a> &nbsp;These large and small articulated gingerbread men are print in place designs that have moving arms, legs, and a neck. Not a large bend, but still nice. &nbsp;The only recommendation I have printing-wise is make sure the joints are strong, so if you can add infill there, do it. I share in the photos where I added boxes to put 100% infill in sections of the design. &nbsp;Designed in Tinkercad. Used mostly basic shapes and scribble for the frosting decorations. &nbsp;Pretty proud of the design as it's my first try with print in place and joints. I messed around with the articulated joint quite a bit and would give them to my daughter to play with to see if they would break. Currently, I don't think she's broken this joint.&nbsp;You can put a hole in the head for hanging on the tree, but he actually stands and lays in the branches quite well! Also looks great in a stocking!&nbsp;I put in the blank gingerbread person so you can import it into your favorite CAD program and add your own frosting decorations if you want!Also has Instructable to go along with it: <a target="_blank" href="https://www.instructables.com/Articulated-Gingerbread-Man/" rel="nofollow noopener">https://www.instructables.com/Articulated-Gingerbread-Man/</a> &nbsp;Edit and decorate your own Gingerbread man on Tinkercad (please share the results here!): <a target="_blank" href="https://www.tinkercad.com/things/bhqRDR09xfe-articulated-print-in-place-gingerbread-man" rel="nofollow noopener">https://www.tinkercad.com/things/bhqRDR09xfe-articulated-print-in-place-gingerbread-man</a> &nbsp;I haven't printed this yet on my Bambu, but it has a good base and I don't imagine you'll have issues with sticking. &nbsp;Some possible recommendations are ironing the frosting layer if you want that smooth and using Herbert Curve infill on the top layer of the gingerbread for texture as I saw recommended here for another gingerbread design: <a target="_blank" href="https://www.printables.com/model/98582-pull-string-gingerbread-man-print-in-place" rel="nofollow noopener">https://www.printables.com/model/98582-pull-string-gingerbread-man-print-in-place</a>

Articulated Print in Place Gingerbread Men

Noël 

Bellamys3DPrints

Supportless, Print-in-place, Articulating Fidget Toy Here we have the Cute Flexi Turtle.This is an articulated print in place model that prints perfectly in PLA. When you print this, don't forget to post on social media or as a make as I LOVE seeing and resharing your makes!&nbsp;To obtain a commercial licence, please purchase a membership on my Thangs here: <a target="_blank" href="https://thangs.com/designer/Bellamys3DPrints" rel="nofollow noopener">https://thangs.com/designer/Bellamys3DPrints</a>&nbsp;Find me on all platforms here:Instagram- (TAG ME HERE): <a target="_blank" href="https://www.instagram.com/bellamys3dprints" rel="nofollow noopener">https://www.instagram.com/bellamys3dprints</a> X: <a target="_blank" href="https://x.com/bellamys3dprints" rel="nofollow noopener">https://x.com/bellamys3dprints</a>Thangs: <a target="_blank" href="https://thangs.com/designer/Bellamys3DPrints" rel="nofollow noopener">https://thangs.com/designer/Bellamys3DPrints</a> Cults: <a target="_blank" href="https://cults3d.com/en/users/Bellamys3DPrints" rel="nofollow noopener">https://cults3d.com/en/users/Bellamys3DPrints</a>Makerworld: <a target="_blank" href="https://makerworld.com/en/u/2061287855" rel="nofollow noopener">https://makerworld.com/en/u/2061287855</a> CrealityCloud: <a target="_blank" href="https://www.crealitycloud.com/user/2275929495" rel="nofollow noopener">https://www.crealitycloud.com/user/2275929495</a>&nbsp;Thankyou and i appreciate all your support!

Cute Flexi Turtle

animaux

3D design shop

My flexible skeleton.&nbsp;It&#39;s a fun piece of toy that&#39;s incredibly flexible, with virtually all joints capable of movement. It has become a huge hit with the kids at home!&nbsp;If adhesion problems persist, I recommend adding a brim.

Articulated Skeleton - High Detail 

personnages

print in place

OddPlasticity

Thanksgiving is just around the corner, and I wanted to make something that'd a) add a bit of visual pop to the dinner table and b) hopefully make the women in my life say “aww” and then give me a second helping of candied yams … because … come on … when it comes to carbs I am not a proud man. &nbsp;These Thanksgiving “donut pumpkin” lights are what I came up with. All you have to do is slot in a tealight and pop on the lid. The <a target="_blank" href="https://www.walmart.com/ip/Battery-Operated-Warm-White-LED-Christmas-Tealights-6-Count-by-Holiday-Time/1257535645?athbdg=L1102&from=/search" rel="nofollow noopener">Walmart Holiday Time</a> brand fits perfectly.&nbsp;Hint: if you look closely, you'll see a bump on the base and the lid – just line those up and you are sweet as candied yams. Printing (TLDR: It's easy)I made these to be easy to print – because no one wants to work hard this time of year, myself included.For the bases, just turn on supports. That's it. The only bit that might need support is the stem overhang. For the tops, these have a flat bottom layer which helps hugely with print reliability. Just turn on the supports, and it prints like a charm. You may want to add a brim, but I never needed to. &nbsp;&nbsp;Did this make you happy?Then by all means, please feel free to <a target="_blank" href="https://www.buymeacoffee.com/mlambertfrw" rel="nofollow noopener">grab me a coffee</a>. No joke, it makes me happy every single time someone drops me a fiver. &nbsp;&nbsp;Want more pumpkins and similar shiny stuff?Learn more about other things I'm making on my Buy Me A Coffee page. &nbsp;&nbsp; I hope you all have an amazing Thanksgiving, you glorious makers.

Cute Thanksgiving Pumpkins - tealight ready

Halloween

Madness3D

Jack o Lantern inspired drink coasters for decoration and use.&nbsp;Coasters has size of 10CM, Coaster base fits 5-6 coasters.

Halloween Coasters

sous boc

agepbiz

<figure class="media"><oembed url="https://www.youtube.com/watch?v=6RgBXBwwXBg"></oembed></figure>&nbsp;edit: 04.03.24 added accessories - canvas top (separate print, no support needed)&nbsp;Print in place kit-card toy. Use a pair of flush cutters to separate the parts then assemble the toy. I have included both a single color version and a multicolor version. I wanted to do a project where I used several tools and machines to tie it all together into one project&nbsp;The Jeep Kit Card: <a target="_blank" href="https://makerworld.com/en/models/223303#profileId-241285" rel="nofollow noopener">https://makerworld.com/en/models/223303</a> The Trailer: <a target="_blank" href="https://makerworld.com/en/models/428258#profileId-332362" rel="nofollow noopener">https://makerworld.com/en/models/428258</a>The Gun:<a target="_blank" href="https://makerworld.com/en/models/469311#profileId-378676" rel="nofollow noopener">https://makerworld.com/en/models/469311</a>&nbsp;Subscribe or follow me on: Instagram: <a target="_blank" href="https://www.instagram.com/agepbiz/" rel="nofollow noopener">www.instagram.com/agepbiz</a> YouTube: <a target="_blank" href="https://www.youtube.com/user/agepbiz" rel="nofollow noopener">www.youtube.com/user/agepbiz</a> Twitter: <a target="_blank" href="https://twitter.com/agepbiz" rel="nofollow noopener">www.twitter.com/agepbiz</a>&nbsp;WARNING: CHOKING HAZARD - Small parts Not for children under 3 yrs.&nbsp;Printsettings: No support No raft 0,16mm layer height

Jeep Kit Card

kit cards

Every Day Counts

Here is a cute design that is worthy of your desk. You could use it as a trash can, or why not hide your stationery supplies there?What about your desk snacks?&nbsp;This is a straightforward print, even though it has several parts to assemble. I like that—it makes me feel like I am contributing to the build.&nbsp;Standard dimensions: 140mm x 130mm x 170mm (or depending on where you are - 5½ x 5 x 6 ½ inches)The print scales up and down in size without issue. The smaller bin in the photos is printed at 100% (around 9cm across), and the larger one at 150%. Feel free to change it up to the maximum size of the bed, but be sure to scale each part accordingly.&nbsp;The wheels swivel and roll.&nbsp;I hope you enjoy this model as much as I enjoyed designing it and bringing it to life. Please give it a like, collect it, and print it out.When done, make sure that you leave a rating and a nice comment and drop in a photo. It sounds like a lot of work on your part, but it won&#39;t take you a second, and it makes me feel better about the time I put into this. If you want to help me even more, then follow ‘Every Day Counts’ as well.😀&nbsp;COMMERICAL USE: A licence for commercial sales of prints of this model is available at <a href="https://cults3d.com/:1998350" rel="nofollow">Cults3D</a>. <h2>Assembly</h2><ol><li>Remove the brims from the smaller parts and place the waste into a trash bin. Don&#39;t have a bin? See my <a target="_blank" href="https://makerworld.com/en/u/369067369/collections/152377" rel="nofollow noopener">collection</a>. 😂</li><li>Assemble each wheel by pushing each tyre into the wishbone frame. I find it easier to place the frame on a flat surface and then push the tyre in from above.</li><li>Align each castor with the hole and gently twist it in to insert it into the bottom of the main bin.</li><li>Add the lid to the bin.</li><li>Lay the bin on the side on a flat surface.</li><li>Align the push connector so that the split aligns with the vertical line on the main body. Press this into place.</li><li>Repeat adding the connector pin for the other side.</li></ol>The pins should be held in place by themselves. If they don&#39;t, add a Superglue drop (CA).&nbsp;

The swing-top dumpster

objets funs

RJ Design

The Design&nbsp;Quick and Easy tool to help with changing the A1 and A1 Mini Nozzle.&nbsp;It has parts to help remove the cover, remove the sock, open the latch, and pull out the hot end&nbsp;Please only use this after hot end has cooled.&nbsp;Printing in PLA works great. No supports needed. &nbsp;If you find this isn&#39;t flexible enough, or wears too quickly try printing in PETG this is a bit more elastic and flexible, &nbsp;My WorkAfter many years in Engineering, I&#39;ve just decided to try and follow my childhood dream of becoming of a Creative DesignerAn Creative Designer of what? No idea! Right now, I really like puzzles, mechanisms and kinetic sculptures so that&#39;s where i&#39;m going to focus my efforts.

A1 A1mini Nozzle Changer & Hot end Sock Remover

outils / pratique

Ciuf_Ciuf

<h2>General description</h2>After the great success of the drainage project, I am proposing a simpler and more intuitive version, especially for new users and beginners who are approaching the world of multicolor.&nbsp;<a target="_blank" href="https://makerworld.com/en/models/54909#profileId-56456" rel="nofollow noopener">https://makerworld.com/en/models/54909#profileId-56456</a>&nbsp;The basic purpose is always to minimize purging material as much as possible to save on color changes and drastically reduce the amount of discarded materialI have decided to update the model and make it more user-friendlyThe basic idea was to make it a standard Bambulab Calibration, similar to the K calibrationSo, lines with numbers to instantly identify which value is the most accurate to assign to the purging of the respective materialBeing a test, it must be as economical as possible, so a test strip requires only 2 grams&nbsp;I'm leaving you the video of a guy who explains in detail how to use this type of calibrationI thank him for considering my project for the creation of a video on YouTube, and I'm pleased that I've shared his video<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=FP3CwBX6A4I"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/FP3CwBX6A4I" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure><h3> </h3><h3>Pre-print Procedure</h3>*Edit 03-01-2024*&nbsp;From one of the various print profiles you download, you'll need to set the color combination you desire<figure class="image image_resized" style="width:47.04%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2024-01-03_36c2f25737bbb.png"></figure>In my case, I'm calibrating these purge combinations, and the model will result like this<figure class="image image_resized" style="width:36.6%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2024-01-03_e5017ae8f46d08.png"></figure>If you want to change the color combination, simply use a different type of filament<figure class="image image_resized" style="width:37.2%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2024-01-03_a174ecda4566d.png"></figure>and the print profile will adapt to the combination you have set, as in this case<figure class="image image_resized" style="width:37.37%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2024-01-03_f1abfb2fe5f0a8.png"></figure>The model will update in real-time, allowing you to see immediately which color you are changingI've implemented additional print profiles to significantly streamline the procedure.While the process can be fast for those with a single AMS, it might be quite lengthy for those with multiple using the previous print profiles.With these new print profiles, there is also increased compatibility for the A1 Mini model.&nbsp;The idea of implementing the print profiles in this new way was suggested by Michael when he uploaded his print profile for the V1 model. I'll leave you the link to his Makerword channel (<a target="_blank" href="https://makerworld.com/en/u/2954682459" rel="nofollow noopener">https://makerworld.com/en/u/2954682459</a>)&nbsp;As on the previous model, it is necessary to reduce the purging material to allow us to calculate the material quantity adequately.The only significant difference is that this time we set all purging quantities to 0On the dual-object print profile, you can also do it manually.However, on the other print profiles, if you want to expedite the process, you can set the multiplier to 0, instantly reducing the purge to 0<figure class="image image_resized" style="width:35.51%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2023-12-29_f161c5ce7c0868.png"></figure>Now you can start the printing process&nbsp;Note: Do not touch any other parameters I've set, or the colors won't be printed in the correct order<h3>Calibration reading</h3>After completing the print, for calibrating the K factor, we need to read and determine the most accurate value to set as the purging quantityWhat you will find in front of you will be this<figure class="image image_resized" style="width:46.93%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2023-12-29_02e09355d1abf8.jpg"></figure>As you can see inside the two green rectangles, that is the exact moment when the material is purged, and the next color takes over.<figure class="image image_resized" style="width:46.78%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2023-12-29_617da72c674e78.jpg"></figure>At this point, all that's left is to identify the correct value and set the purging quantity for that specific color changeFor these tests, it's highlighted that 150mm^3 of material is required to perform the color change<figure class="image image_resized" style="width:46.33%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2023-12-29_e9817c7179a71.jpg"></figure>In this specific case, the quantity is identical for both color changes, but for other combinations, it may varyAs you can see, the difference between the default values of Bambustudio and the ones just found is significantly lower.This allows us to reduce material waste and significantly cut down on print times, decreasing the time the printer takes to change the filament<figure class="image image_resized" style="width:35.41%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2023-12-29_a67e103190684.png"><figcaption>BEFORE</figcaption></figure><figure class="image image_resized" style="width:35.53%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2023-12-29_ab83cab72d7d18.png"><figcaption>AFTER</figcaption></figure>&nbsp;