anderson.mfa

Crafty Sven

Rupee

Zelda

Skylar Xu

漫画《电锯人》中的波奇塔，不同颜色分件打印组装，不需要多色打印。建议使用拓竹绒毛表面功能效果更佳。原始模型文件中包含不分件的整体模型，不希望花太多时间打印组装的朋友们可以考虑。Pochita in《Chainsaw Man》.Different colors are printed and assembled separately, eliminating the need for multi-color printing.Suggest using the Bambu Studio to enhance the surface functionality and achieve better results.The initial model file contains the overall model without parts, which can be considered by friends who do not want to spend too much time on printing and assembling.

Pochita in《Chainsaw Man》，漫画《电锯人》中的波奇塔

Anime

Cloudy Nostalgia

How to support me!If you like my work, consider joining my Patreon where you can have a say in what I print next! Only Patreon members get to see those items and you can even sell them at a certain tier. Finally, if you’d like to learn my tips and tricks for making a hueforge start to finish I offer a coaching session to some of my patreons! Thank you for all your support!<a target="_blank" href="http://www.patreon.com/CloudyNostalgia" rel="nofollow noopener">www.patreon.com/CloudyNostalgia</a>&nbsp;Also, if you have any questions about how to print a piece of mine or if you need help troubleshooting, feel free to join my discord server where you can ask for help!<a target="_blank" href="https://discord.gg/4ays78UJ" rel="nofollow noopener">https://discord.gg/4ays78UJ</a>&nbsp;Also, I upload videos every so often showing how to videos for Hueforge. If you’d like to view here is the link:<a target="_blank" href="https://www.youtube.com/channel/UCG1IDrymVjUyYng7nXrdGnw" rel="nofollow noopener">https://www.youtube.com/channel/UCG1IDrymVjUyYng7nXrdGnw</a>&nbsp;**IMPORTANT INFORMATION**<ul><li>You cannot adjust the z scaling on any hueforge. This will mess with the coloring done and your hueforge will not come out as intended. You can however change the x and y to scale the picture. I recommend only changing by the same percentage. </li><li>To get an accurate print as shown in the photos you MUST use the same filaments listed below. You can change brands (as long as they are similar) but keep the filament colors the same. If you use any other color, you will not get the same results as me. </li><li>What you see in the slicer will not be how the final results will look! Hueforge takes advantage of color bleed to make the blended colors!</li></ul>Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used: PLA BambuLab Basic Black Transmission Distance: 0.6 PLA BambuLab Basic Blue Gray Transmission Distance: 3 PLA BambuLab Basic Orange Transmission Distance: 6.2 PLA BambuLab Basic Jade White Transmission Distance: 3.5Swap Instructions: Start with Black At layer #14 (1.2mm) swap to Blue Gray At layer #19 (1.6mm) swap to Orange At layer #25 (2.08mm) swap to Jade White for the rest.

Hueforge - Dragon Ball - Goku Poster

Quadros

TBone_427120

This lampshade is designed for the <a target="_blank" href="https://makerworld.com/sv/models/13717#profileId-13429" rel="nofollow noopener">Bambu Led Lamp 001</a> kit ←- Follow this link to get the model for the base that holds the electronics and that this globe shade locks into.&nbsp;This is a moon lithophane model for the LED Lamp kit base built using NASA SVS data.&nbsp;Before printing, it is highly recommended to test and calibrate the filaments. Test Prints are provided in a profile to test the trickier parts of the print, in particular the top of the moon. Printing the sliced off moon top will give an idea if the flow rates need to be calibrated or if the layer heights need refining.Both of these are eSun PLA, and both were printed using the same eSun PLA+ profile. <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_e7cbdab0e3545.jpg"> The one on the left (&#34;creamy&#34;) needed different flow rate settings to avoid the gaps in the thin walls. Moral of the story: spend the extra 20 minutes to at least run the Auto Calibration for a new filament (and Manual isn&#39;t so bad to do either particularly if you print on the textured plate).&nbsp;The extra big brim is out of an abundance of caution. There is nothing worse than being ten minutes from the end of a 17 hour print and hearing *CRACK* followed by a spaghetti detected notification. If the test print indicates your filament needs a small center support for the top of the moon, “Normal/Snug” supports will work best. Use Manual supports (Auto will result in a ton of exterior supports for the base of the moon) and paint a small dot in the underside of the top of the Moon. The latest version of the model has been made a little thicker and is more forgiving for printing with most filaments. The part that interfaces with the lamp kit base can easily be made a different filament to match the LED holder material or just for variety. Just set the base filament for the “ModifyBaseSettings” modifier. Doing will require only one filament purge, no prime tower is necessary.<figure class="image image_resized" style="width:41.3%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_33ea3c815b5ef8.png"></figure>&nbsp;If using the modifier to make a material change at the base, make sure to pick two filaments that have good adhesion to each other.Because the print requires supports in the base and cleanly removing those supports is important for a snug fit to the lamp kit base, a test print is provided to make sure the filament and support settings will release cleanly. Normal snug supports provided the best results (tree supports required much more effort).&nbsp;<figure class="image image_resized" style="width:17.23%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_f00e2d2199c81.jpg"></figure>&nbsp;If you do use the center support, when removing don&#39;t pull at individual folds from the bottom. Use something to grab on multiple folds as far up as possible (a pair of kitchen tongs works well) and twist.<figure class="image image_resized" style="width:17.52%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_c2509972a68348.jpg"></figure>Twisting will put less stress on the top of the sphere and less risk of pulling away the moon surface. If you have wisps of filaments, resist the urge to use a heat gun because the variable thickness of the shell will contract non-uniformly under the heat. This is the result using a heat gun on a lithophane:<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_a27a97fbc55ec.jpg">&nbsp;

Moon Globe for LED Lamp 001

Luminárias

Water Filter Wall Mount - No drilling