Actoes93

DesignCraft

This model widens one side of the spool ring adapter to stabilize a R3D 1kg 194x58mm cardboard spool while it rotates within a Bambu Lab AMS.&nbsp;Features:<ul><li>Reusable</li><li>R3D nameplate for easy identification when reusing</li></ul>Instructions:<ul><li>Print one of each model for a single spool.</li><li>Affix the wide spool ring adapter on the right-hand side of the R3D spool if you're facing the AMS.</li><li>See attached photos.</li></ul>Considerations:<ul><li>Print Material: Please print with a basic PLA or PETG to minimize any shrinkage.</li><li>Too Tight? Too Loose? Cardboard expands with humidity and contracts when dried. A cardboard spool that has absorbed too much moisture may cause the adapters to fit very tight. Placing the spool in a filament dryer, such as the SUNLU S2, for a bit should resolve this. Note, you should not dry the spool with the adapters attached as they can warp in the heat. Keep in mind that after a long drying session the adapters may fit too loose. This should resolve itself shortly as the cardboard reabsorbs some moisture from the air.</li><li>AMS Lid Doesn't Close? All of the spool adapters I make are less than the official AMS spool clearance limit of 202mm, as specified on the official AMS product page, and as tested within my own AMS. However, some people have stated their spools are rubbing against the lid with the adapters attached. It's hard to say what's causing this since I cannot reproduce the issue myself, however, I've created an <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">AMS Lid Riser</a> which allows you to keep your AMS lid closed while providing additional clearance for larger filament spools. It's a quick and easy print which you can find on <a target="_blank" href="https://makerworld.com/en/u/243407759" rel="nofollow noopener">my profile</a> or directly here: <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">https://makerworld.com/en/models/33133</a></li></ul>

R3D Bambu Lab AMS Cardboard Spool Adapter Ring

X1C upgrades

Emoticon

The vinyl caps that I have had for different SMA connector radio devices I have were always falling off. I made these with the correct ¼-36 thread so that they stay on and don&#39;t fall off. Print with thin layers for the best detail on the knurling and threads. No supports needed.

Threaded SMA connector caps (FPV Drone, RTLSDR)

To print

agepbiz

<figure class="media"><oembed url="https://www.youtube.com/watch?v=6RgBXBwwXBg"></oembed></figure>&nbsp;edit: 04.03.24 added accessories - canvas top (separate print, no support needed)&nbsp;Print in place kit-card toy. Use a pair of flush cutters to separate the parts then assemble the toy. I have included both a single color version and a multicolor version. I wanted to do a project where I used several tools and machines to tie it all together into one project&nbsp;The Jeep Kit Card: <a target="_blank" href="https://makerworld.com/en/models/223303#profileId-241285" rel="nofollow noopener">https://makerworld.com/en/models/223303</a> The Trailer: <a target="_blank" href="https://makerworld.com/en/models/428258#profileId-332362" rel="nofollow noopener">https://makerworld.com/en/models/428258</a>The Gun:<a target="_blank" href="https://makerworld.com/en/models/469311#profileId-378676" rel="nofollow noopener">https://makerworld.com/en/models/469311</a>&nbsp;Subscribe or follow me on: Instagram: <a target="_blank" href="https://www.instagram.com/agepbiz/" rel="nofollow noopener">www.instagram.com/agepbiz</a> YouTube: <a target="_blank" href="https://www.youtube.com/user/agepbiz" rel="nofollow noopener">www.youtube.com/user/agepbiz</a> Twitter: <a target="_blank" href="https://twitter.com/agepbiz" rel="nofollow noopener">www.twitter.com/agepbiz</a>&nbsp;WARNING: CHOKING HAZARD - Small parts Not for children under 3 yrs.&nbsp;Printsettings: No support No raft 0,16mm layer height

X1C upgrades

To print

cool prints