My latest model is up. I tried branching out and solving a problem that has been annoying me for years: Shampoo and shower gel bottles falling on the floor! I added a cut out on the front so that it could hold any bits and bobs you might need. Very happy with how this came out so I designed another version for my sister. #Newmodel https://makerworld.com/en/models/1963711-corner-shower-caddy-bathroom-shelf-with-drainage#profileId-2111042

A1 Printer Melted Board UPDATE: Hi Everyone, I am one of the many people who have been affected by this issue and wanted to give an update on my current situation and experience with BBL Support. About 3 weeks ago, my printer smelt like burnt plastic and completely died mid print. The light was on at the back but nothing I did could get it to boot. I flipped it over and found a melted hole where a part of the board inside had melted into the surrounding parts and through the outer plastic casing. I was pretty upset with this, 3DP is my most expensive hobby by far and after spending a significant amount of both money and time to find that my printer only lasted me 5 months was very disheartening. I reached out to support who, despite the day long response time, were very helpful able to come to a solution. I had to send my printer back and it was then a replacement unit was sent to me. Whilst I am very grateful for this, I still am not entirely confident with the printer and it feels like unless this issue has been fully addressed, I am just on timer for this to happen again. I've seen many posts online and some have been unlucky to have this happen in the first two weeks. It will be difficult due to my personal circumstances but I will try to save up for a model that does not have this issue going forwards. Any support for this would be much appreciated. Please like, download and print my models if you can! I hope to improve my quality and be able to design more things for people to enjoy.

Hi everyone, I am waiting back to here from support. I'm hoping for an update this week and confirmation the following to help resolve my issues with the A1. I have been hard at work publishing models and have put out 5 models in the last week! Most are small models but I designed a custom case for one of my figures that came in packaging I did not like and was not able to display in. It's very niche and likely wont get many downloads but I made that one for me and to experiment with AMS functionality, anything else is a bonus :) Recently I have come across a hesitation of sorts when modelling. Almost like procrastination but it feels more like a fear of failure, or in this case wastage. I have many things I want to design and print but I need it to be perfect so that the first print is perfect. I will do small test prints but any larger prints (100g+ - yes thats large for me) it is a real struggle to motivate myself to make. Has anyone else come across this? If so. how did or how are you managing this? #Questions #Sharing Makes

Hi everyone, I hope to have a resolution by next week regarding the issues with my A1 printer, In the meantime I have found a work around so that I am still able to upload models here to makerworld. I find it easier to design models of thinks I enjoy and so my latest model is the fullbring bankai of Ichigo from Bleach. https://makerworld.com/en/models/1914881-dummy-13-fullbring-bankai-ichigo-kurosaki#profileId-2053951

I very recently hit 100 makes across all my models on Makerworld! Thanks to everyone who as supported and printed my models. IT hasn't been easy learning fusion and blender. There have been many frustrated evenings and I still only feel like I'm scratching the surface. However being able to model parts of toys that are no longer in production and being able to see them helping others is a great feeling. I've recently started working on D13 accessories and have learnt a lot about managing supports and tolerances. Unfortunately I have had a severe issue with my printer so I will have to take a little step back but I am working on lots of projects of which I hope are good enough quality to share with you all. Here's to the next 100 and I hope for your continued support. All my Power Ranger Toy Line Parts can be found here: https://makerworld.com/en/collections/8517715-power-rangers-toyline-collection All my Dummy 13 models can be found here: https://makerworld.com/en/collections/10127462-zen-aku-s-dummy13

Unfortunately my A1 has burnt a hole in itself. After looking online this seems to be a rare, but consistent occurrence amongst this model. I am feeling very upset and disappointed partially because I had faith in the brand, and partially because I had finished designing a few projects that just needed printing before uploading. I am not confident that I will receive adequate support and so I would appreciate likes, shares and boosts so that I may be able to get back into the hobby that has been helping me during one of my low points of my health.(Edited)

Hi everyone, I seem to have writers (creators?) block and struggling to come with a design to upload for you all. Sticking with my theme of action figure / Dummy 13 accessories, should I just release a sword handle and say it's Byakuya's Shikai? 😂 I'm kidding but if there any suggestions or recommendations let me know below!

I've put out a few Dummy 13 scaled weapons that would also work great for any figures scaled 5"-6". https://makerworld.com/en/collections/10127462-zen-aku-s-dummy13

I've wanted to recreate this scene ever since I watched Bleach and now you can too with Dummy13! I tried to do the famous moon picture (don't search if you don't want spoilers for TYBW) Let me know what you'd like to see next! https://makerworld.com/en/models/1819268-dummy-13-wabisuke-izuru-kira-zanpakuto-shikai#profileId-1941727(Edited)