XerxesTech

Techro3D

Classic bird feeder | octagonal house | with mounting bracket| By Techro3D&nbsp;<ul><li>Water drainage.</li><li>Mounting bracket.</li><li>Suspension point for a fatball or other bird food.</li><li>Bottom also suitable for placing food.</li><li>Removable roof.</li><li>100% printable.</li><li>No glue required, but can be used just to be sure.</li></ul><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000453035/design/2024-05-04_a142276d19e56.png"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000453035/design/2024-05-04_bf6862079a949.png"></figure>

Classic bird feeder, octagonal house.

Gardening

hsispeg

Model of an ejection seat handle. Comes with a seat belt buckle silencer and with a vice adapter.

Ejection seat handle (e.g belt plug / silencer)

Automotive

BODY MECHANIC

Drain Cleaner

Drain Cleaner

House

ByteSlinger

This is a tidy little support to rest your spoon (or other cooking utensil) on whilst cooking, avoiding getting it or your kitchen counter messy whilst you do so. It can support large and small utensils (as pictured, with both large cooking spoons, as well as a table spoon).Whilst it'll print fine in PLA, this is one of the few things I'd suggest printing in PETG, as not only is it (depending on supplier) classified as a food-safe material, it'll also better tolerate a higher temperature making it more suitable for cleaning. Also, regarding food-safe, as the ‘head’ of the utensil you rest on it never makes contact with the stand itself, that's even less of a concern. As well as a stand, it also features a cupped base to catch any drips from the spoon. The cupped base is approximately 60x100mm, and due to surface tension causing any liquids on your spoon to generally hang on until the lowest point before dripping down, this drip tray will cover some super large spoons and keep your counter clean!&nbsp;Print settings<ul><li>Layer Height: 0.08 (for quality and to minimize gaps where bacteria can live, smaller layer lines creating smoother finish is best, but really you could print this at any layer height you like)</li><li>Walls: 4 (I've suggested for to keep it as water tight as possible, but you could drop as low as 2 if you needed)</li><li>Infill: 25% Gyroid (whilst it doesn't need strength, as there is a big flat top surface, and you want to avoid any holes, you'll want a decent infill percentage to support that top surface)</li><li>Material: PETG (I recommend PETG for this due to the reasons stated above, but any material will work fine)</li><li>Orientation: Print in the orientation it should be used (as pictured), big flat base down.</li><li>Support: None</li></ul>

Spoon Rest

Kitchen

Vixvvo 3D

commercial licenses will be accessible through my Patreon page, 'Vixvvo3D', at the affordable rate of $6 per month. I aim to consistently post and model new content on a weekly basis. Your support on <a target="_blank" href="https://patreon.com/Vixvvo3D" rel="nofollow noopener">https://patreon.com/Vixvvo3D</a> is greatly appreciated! (edited)&nbsp;If you want a particular size, use the provided print profiles. If you like to experiment, get the Fusion 360 file and adjust various settings. The design ensures that all punch holes are automatically calculated and evenly placed. You don't need to mess with manual settings, just set the basics and let the math do its work. The rows of punch holes are automatically calculated and will be centered on the outer wall. <figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=3GQHaYdmULs&t=110s"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/3GQHaYdmULs?start=110" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure><h3>Customizable Parameters:</h3><ul><li>Height</li><li>Width</li><li>Length</li><li>Wall thickness</li><li>Corner Radius</li><li>Save space on the top and bottom</li></ul>

Storage Bin/Box With Cover (Parameterized)

Storage

JosepMY

Blank 16mm dice to customize for your projects.

Blank dice 16mm

Game

Uncle Joeys Creations

Articulated Elf on the Shelf. Have 2 versions available one for print face down which is already the orientation for a smooth finish, the other is a layered version for those without an ams or that want it to stick out more with the face print that version facing up. The layered version files are named that way.

Articulated Elf on the Shelf

Christmas

JonnayLin

Took a great model and just added a little lip on the inner side so that it wouldn't slip. Some of my Overture rolls have slightly smaller diameters than others. Some of the cardboard is also a bit thicker than others, so I made them in varying thicknesses from 2.8mm to 3.7mm. 3.4mm is what I use for my Overture rolls. Printed with PETG at 0.2mm layer height. I use the stock PETG profile with decreasing perimeters to 50 mm/s to get a better surface finish.