WhiteIronWolf

BamBam Design

<h4>Toroidal Windmill - Self adjusting turbine</h4>Looks like a spinning flower and no much wind is needed.<a target="_blank" href="https://youtube.com/shorts/WrKHW2Cdyvk?si=byQ_EpJAfOOy8x7F" rel="nofollow noopener">YouTube Short</a>&nbsp;<ul><li>Beautiful Windmill with toroidal Propeller Blades</li><li>Self adjusting to wind direction (Tail Blade Reworked)</li><li>100% printed, no Screws or tools needed</li><li>You can add 3 Propellers on one Axle with 2 distances</li><li>Full customizable with different propeller sizes and directions (I plan to add more cool propeller types as well)</li><li>Rods are stack able to your needed height</li></ul><h4>Printing:</h4>You can choose Propellers from 3 Print Profiles<ul><li>Basic Parts with Left&amp; Right Propeller to choose</li><li>Additional Propeller Blades</li><li>Additional Slower Propeller *New</li></ul>You can mix the propellers from these profiles.<ul><li>added one profile for A1mini without the biggest blade as well</li></ul>The rod could be a bit difficult to print, i added custom support, but clean your buildplate and apply some glue.&nbsp;PETG &amp; PLA tested👍🏼<h4>Assembly:</h4><h4>Info:</h4><ul><li>Added custom support to the horizontal printing rod</li><li>Added optional longer axle for more distance between propellers (10mm instead of 5mm).  With stronger wind the bigger blades should not collide.</li></ul>The Pitch from the Basic Blades:<ul><li>Big - Pitch 195mm</li><li>Med - Pitch 170mm</li><li>Small - Pitch 135mm</li></ul>Additional Propeller Blades with different numbers of Wings:<ul><li>Big - Pitch 190mm</li><li>Med - Pitch 160mm</li><li>Small - Pitch 130mm</li></ul>Additional “Slower” Propeller Blades:<ul><li>Big - Pitch 400mm</li><li>Med - Pitch 325mm</li><li>Small - Pitch 250mm</li></ul>Thanks to all followers and don&#39;t forget the virtual handshake 👍 ….Happy Printing&nbsp;Info II:My other windmills are fully compatible if you want to mix it up:<ul><li><a target="_blank" href="https://makerworld.com/models/235261" rel="nofollow noopener">Toroidal Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/250216" rel="nofollow noopener">Honeycomb Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/388124" rel="nofollow noopener">Elliptical Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/425419" rel="nofollow noopener">Sunflower Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/454861" rel="nofollow noopener">Raccoon Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/255324" rel="nofollow noopener">CLAMP for Windmills</a></li></ul>Info III:More modifications you find on my Patreon account.<figure class="image"><a href="https://www.patreon.com/posts/mod-608-bearing-105175595" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000235261/design/2024-05-30_3ad9786c3df1b.png"></a></figure>&nbsp;<figure class="image"><a href="https://www.patreon.com/posts/mod-pole-adapter-103628897" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000235261/design/2024-05-30_70c92ad1f54a9.png"></a></figure>&nbsp;Commercial license you can get here:<a target="_blank" href="https://www.patreon.com/BamBamDesign/membership" rel="nofollow noopener">https://www.patreon.com/BamBamDesign/membership</a>

Toroidal Windmill - Customizable system

Outside things

Jeff Smith

I mainly use 10mm 4 wire LED strips, and while there are 8mm and 12mm soldering jigs out there, I present to you my vastly over-engineered 10mm soldering jig! :) Seriously, needed one for the 10mm I use and since I couldn't find one here, I made one. Note: I use 22-gauge wire in this. While it should work with just about any 10mm LED, I use <a target="_blank" href="https://amzn.to/3oHOXkx" rel="nofollow noopener">https://amzn.to/3oHOXkx</a> Since publishing this model, I've uploaded the following for soldering two 10mm LED's together. <a target="_blank" href="https://makerworld.com/en/models/227522#profileId-245137" rel="nofollow noopener">10mm 2x LED Joining LED Soldering Jigs by Jeff Smith - MakerWorld</a> <img src="https://makerworld.bblmw.com/makerworld/draft/639182/2024-03-04_bc4452b74fabc.png">

10mm LED Strip Soldering Jig

Useful Tools and Items

kelwind0

My wife wanted some Easter Gnomes. I printed them face down.

Easter Gnomes

Easter

iLab 3D

A guitar-playing skeleton&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm - 1 loop&nbsp;Filaments Used: PLA+ Sunlu Black Transmission Distance: 0.6 PLA+ Sunlu Grey Transmission Distance: 2 PLA+ Sunlu Silver Transmission Distance: 2 PLA+ Sunlu White Transmission Distance: 5&nbsp;Swap Instructions: Start with Black At layer #5 (0.48mm) swap to Grey At layer #8 (0.72mm) swap to Silver At layer #14 (1.2mm) swap to White for the rest.

Skeleton playing guitar - HueForge

Halloween

秋瑟意浓

塞尔达大师剑-陀螺推牌，模型需要用到r188轴承一个，5*2圆形磁铁8个，剑鞘分两版，早期剑鞘为上下结构，后期改进版为三明治结果，可以很好的隐藏接缝，方便涂胶水隐藏痕迹

塞尔达大师剑

Swords

standitupstore

The Master Sword from Tears of the kingdomsplit in half dowel in center to connect Parts or can be used for LEDs&nbsp;Offsets pieces for the stand plaque are on the last plate&nbsp;

The Legend of Zelda: Tears of the Kingdom Master Sword - LED through center 

Zelda 

Beda_Bedrich

Tisk na tiskárně Ender3 MAX tisková plocha 300x300mmK montáži je potřeba 4ks kolaZávitovou tyč M44ks ložiska 6700zz (10x15x4)24ks šrouby M3 x 20mm10ks šroub M3 x 30mm34ks matice M34ks matice M4Hlinikovy U-profil 8x8mm,délka 60cm4ks kol z rc modelu

RC trailer

R/C Toys

i.koettker

Hot Wheels Display Remix (Bambu AMS Color Mode)

Hot Wheels Display Garage with Color Logo (BambuLab)

Model Displays

maximdivirgilio

The Planet Express Ship - Futurama 1 : 100 Scale Model Requires Minimal Support

The Planet Express - Futurama

Futurama 

GiskardReventlov

Only print the “print-in-place” version in PLA and if you are certain of your printer and filament tolerances and that your filament is well dried. Otherwise, print the parts separately using printing supports on the shelf support part (Support_ONLY.stl).--------------------------------------Update 1: Added a version with a longer front lip that fits better if your monitor has curved or thick bezels and fixed the weird slicing bug that added strange lines on top of the model.&nbsp;Update 2: I now recommend printing the “Shelf_ONLY” and “Support_ONLY” files separately using supports on the “Support_ONLY” file. Many people reported not being able to separate the parts on the print-in-place version.--------------------------------------A print-in-place shelf for the top of computer monitors and TVs.<ul><li>The support arm is adjustable and has a single contact point with the monitor, so it fits firmly and easily also curved-back monitors.</li><li>Perforated to not block monitor cooling.</li></ul>Instructions to separate the parts after printing (only takes 10 seconds):<figure class="media"><div data-oembed-url="https://youtube.com/shorts/sEQsrMtvIG0"><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=sEQsrMtvIG0"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://www.youtube.com/embed/sEQsrMtvIG0" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>No supports needed for printing, just slice and print in the orientation that the files comes in.<ul><li>Print in PLA! If you want to print in PETG, print the parts separated and use supports, don't use the the “print-in-place” file, it will not separate!</li></ul>It's strong! Don't worry about putting heavy stuff on it - but I wouldn't put any liquid…<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/724759/2023-12-10_hyy4fbaqax0k.jpg"></figure>STEP file included. Feel free to remix and share, but please use the attribution feature.

Adjustable Monitor shelf - Fits any display

computer 

fireboy02

Perfect DND Dice tower for all types of board games. Supports the D20 dice as well as many other dice!&nbsp;No supports needed 2 wall lines15% supportive cubic infill

Castle Dice Tower

DND 

Balzo98

An easy to print duck! No support needed! You can print it very small and hide in some funny spot!

Easy to print duck

duck

Stigern

EDIT: Added a file with better quality.&nbsp;A decoration statue.&nbsp;PS:&nbsp;If you enjoy my designs and maybe want to contribute, you can make a small donation to <a target="_blank" href="https://www.paypal.com/donate/?business=T3KK6HAMWRUPL&no_recurring=0&item_name=If+you+like+my+designs+and+want+to+contribute.&currency_code=NOK" rel="nofollow noopener">paypal, </a>that will be greatly appreciated.

Woman Sculpture Decoration/Statue

statue 

3D servis

I recommend heat, bending and curving the flower piece a bit for easier fit.&nbsp;My next hair clip.Previous Bee & Honeycomb Slide Hair Clip is <a target="_blank" href="https://makerworld.com/cs/models/94001" rel="nofollow noopener">here</a><figure class="image image_resized image-style-align-left" style="width:34.91%;"><img src="https://makerworld.bblmw.com/makerworld/draft/271844/2023-12-15_s7o8gbaq0b0u.jpeg"></figure>

Flowers Slide Hair Clip

Hair Clips 

TheMidnightSmith

So there are a number of paid models out there for this, but I figured I could whip up a free design that will hold both your ears and backpacks or purses. It mounts to the wall with some #4 screws or 3mm if you have them. You can use it with just the ears or just the bag. I printed with 10% infill and 4 perimeters in PLA. Happy printing!

Disney Ear and Bag Holder For Loungefly

Disney

chiz_m

If you like to show appreciation for the effort that went into creating this model, pls hit that BOOST button!&nbsp;A <a target="_blank" href="https://makerworld.com/en/models/18035#profileId-16764" rel="nofollow noopener">base/diorama builder</a> is now available for download for this mini figure model!<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000018045/design/4fb50df1-8c36-4d0c-88ec-bcc8e5122b9c.jpg"></figure>___________<h3>IMPORTANT NOTE ON COMMERCIAL USE OF MY MODELS</h3>Please note that I am sharing my designs to any one to enjoy but for personal use only. I have NOT provided any commercial license to any one allowing the sale of 3d printed copies of my designs. Seeing my designs being sold for profit is discouraging for me to continue coming up with more designs. I will not hesitate to report to Etsy and other online sites if I find them being sold.__________This is a kit card of Minecraft Turtle in mini figure scale. Parts can easily be removed from the sprue without using cutters/clippers just by twisting the part.Default scale is comparable to the Minecraft mini figures but of course you can scale it up to as large as you want! :)<h4>Usage Options</h4><ol><li>Assemble as is and use as toy/collectible; or</li><li>Use the alternative part with loop and glue the halves together to make for a great keychain ornament!</li></ol><h4>Printing Reminders</h4><ul><li>Print as oriented, with NO supports needed.</li><li>If you&#39;re printing in multiple colors, please note that due to several color swaps, it would take longer to print.</li></ul><h4>Difficulty Level (Easy, Medium, Hard)</h4><ul><li>Printing: Medium - Bed should be leveled well to ensure small parts stick well to the build plate. Requires printing slower during the first few layers. May require lots of filament swaps if printed in multi-color.</li><li>Assembly: Easy - Parts should fit really easy. The flippers are intentionally designed to be loose and wiggly. See pictures for correct orientation of the flippers.</li></ul>

Minecraft-inspired Turtle Mini Figure Kit/Keychain

Minecraft

Rustam

<h4>Intro</h4>Simple stands for Miyoo Mini Plus console - minimalistic design and easy to print. There are two versions included - with and without a “My Mini +” text.&nbsp;<h4>Print settings</h4><ul><li>print with 10-15% infill</li><li>no supports</li><li>place the model on face (place on face)</li></ul>

Miyoo Mini Plus Stands

Miyoo Mini +

Martin Kozak

Flat print orientation for the best possible strength. No supports needed.&nbsp;Print settings:<ul><li>For outdoor use, it's better to use PETG.</li><li>For added strength, use these print settings: 3 perimeters, 3 bottom and 5 top layers, 15% gyroid infill.</li></ul>Postproduction:<ul><li>Glue bot halves together using superglue, printed pins will help with proper alignment.</li></ul>To complete the sword, screw the handle into the end of the pool noodle. Suitable for noodles without central hole. No drilling holes needed. Before you screw it all the way in, apply glue to the end of the thread to secure handle in place.

Sword handle for pool noodles

Kids Toys Big and small

Wiseone

I've seen these sub hooks being sold that fit over a coat hangar to allow accessories or even another coat hangar to be dangled from. A simple idea that can be easily reproduced with a 3D printer and at a low cost.&nbsp;Here is my design that duplicates the functionality of the hooks. The choice of 3D filament type is open.&nbsp;My print is made with eSUN PLA+ 1.75mm Orange filament, with 0.2mm layer height and 15% infill on a Bambu X1 Carbon printer. No supports required. No printing rafts required, but support for the hole will improve the print finish.&nbsp;I hope that you can find this print useful, too.&nbsp;Remember to leave me some feedback or even a tip to keep me enthused to make more of these drawings.

Hangar Sub Hook

Organization

goldiesvinyl

Stitch Cookie Cutter V 2

Stitch

NotGrounded

v2.0 with full honeycomb pattern here: https://makerworld.com/en/models/408313#profileId-310259&nbsp;Allows larger bits of food down into the garbage disposal while keeping larger things like shot glasses, utensils, etc out of it.  The largest gap is 0.75&#34; across Diameter is 3.188&#34; (~81mm) Height 0.50&#34;

Garbage Disposal Sink Strainer v1.0

Kitchen

Bleepbloop

I strap this right to my dog's harness or leash and other styles would eventually break or get lost since he is very high energy. Crafted with durability and functionality in mind, this ensures a hassle-free and sturdy experience during your dog-walking adventures. If you appreciate the design and find it beneficial, consider leaving a tip in my bio. Thanks!

Heavy-Duty Dog Poop Bag Holder

Dog Items

PaulBPunkt

After seeing a handful of the Die Hard Christmas tree decorations on Reddit, where I wished the lighter was lit by the Christmas tree lights, I decided to design my own interpretation of this. The ventilation shaft or the position of the hole for the fairy lights is designed for a specific photo motif. The hole has a diameter of 5mm which should hold most common round fairy lights, if you need a different diameter please contact me or adjust it yourself directly in the slicer with a negativecylinder.The eyelet is rasterized so that depending on the weight distribution by the fairy lights a horizontal hanging is simplified. Instructions: Download the specific <a target="_blank" href="https://www.gamebyte.com/wp-content/uploads/2021/05/diehard1-e1620652315794.jpg" rel="nofollow noopener">photo</a> and scale it so that the long side is exactly 10 cm long and print it out. Then all you have to do is cut it out, glue it in and punch the hole for the fairy lights.&nbsp;Happy Printing! :)

*Slightly* overengineered Die Hard tree ornament

Christmas

N3RD solutions

Funny Light switch cover :) Enoy!

Light Switch Plate

Naughty's

johnparilla

I found this Yeti on Printables but it was all one color. This was my first attempt at painting in Bambu Studio.&nbsp;The Yeti turned out awesome! The print took about 9 hours.&nbsp;Supports may be needed under the hands.&nbsp;Link to original: <a target="_blank" href="https://www.printables.com/model/436473-simple-cute-yeti" rel="nofollow noopener">https://www.printables.com/model/436473-simple-cute-yeti</a>

Cute Yeti Monster

Yeti

Frazier Smith

Multicolor Butterfly earrings – no AMS needed. Change color at Layer 11 / 1.2mm

Butterfly Earrings

Ear rings

mclanesmemories

Unusual Mix - What if it took an Octopus to run a lightbulb?? - Set of 3 Bookmarks&nbsp;Please share your prints&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm&nbsp;Swap Instructions: Start with Black At layer #4 (0.40 mm) swap to Brown At layer #7 (0.64 mm) swap to Light Brown or Tan At layer #11 (0.96 mm) swap to white

Unusual Mix - What if it took an Octopus to run a lightbulb?? - Set of 3 Bookmarks

Ocean Critters

Makers Manifest

This is a really cool flat print of some mountain wall art.Category: 2D Art

Minimalist Mountains wall art

Wall Art

Another Set of 3 Celtic Knot Bookmarks - Spirit of the Wolf Designs&nbsp;Please share your prints&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm&nbsp;Swap Instructions: Start with Black At layer #4 (0.40mm) swap to Dark Grey At layer #6 (0.56mm) swap to Light Grey At layer #10 (0.88 mm) swap to white

Another Set of 3 Celtic Knot Bookmarks - Spirit of the Wolf Designs

Wolf

PhaseworksCA

<h3>Experience the power of one of the most legendary Pokémon with our low poly geometric Mewtwo 3D print file. </h3><h3>This design transforms the iconic Mewtwo into a striking, modern art piece with sharp, angular lines and a bold geometric structure. </h3><h3>Perfect for Pokémon enthusiasts and fans of minimalist, contemporary art, this print lets you bring a piece of the Pokémon universe into your world in a unique and stylish way. </h3><h3>Download now and add a touch of legendary elegance to your collection!</h3>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/764945/2024-03-25_9951300e07d46.png"></figure>&nbsp;<figure class="image image_resized" style="width:99.3%;"><a href="https://www.printables.com/@PhaseworksCA/store" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/764945/2024-02-27_cbac20a9d0926.png"></a></figure>

Geometric Low Poly Mewtwo

Pokémon

Bamingo Design

<ul><li>❄ 🌨️ Is your table missing that special seasonal sparkle? Unique snowflakes for your table, each coaster an intricate art of frost.</li></ul>Snowflake Coasters: Unique Seasonal Sparkle<ul><li>🎨 Frosty Design: Each Snowflake Coaster is a unique representation of frost&#39;s delicate art, capturing the unique beauty of snowflakes. Their intricate patterns are designed to bring a touch of winter&#39;s magic to your table.</li><li>👶 Easy to Print: No need for (AMS) or (MMU). Only two manual filament swaps are needed to complete the model.</li></ul>Technical Specifications:<ul><li>📏 Size:<ul><li>10 cm</li></ul></li><li>🔧 Print Settings:<ul><li>Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm</li></ul></li><li>🌈 Color Changes:<ul><li>Start with Blue</li><li>At layer #19 (1.6mm), swap to Light Blue</li><li>At layer #25 (2.08mm), swap to White for the rest.</li></ul></li><li>📋 Assembly and Usage Tips:<ul><li>Alternatively, use our ready-to-print 3MF file—it automates these steps.</li><li>The files are available in STL, Prusa 3MF, and Bambu Lab 3MF file formats.</li></ul></li></ul>Explore More Designs:<ul><li>Dive deeper into our collection of nature-inspired coasters for more designs that capture the beauty of the natural world:<ul><li>🌊 <a target="_blank" href="https://makerworld.com/en/models/25169#profileId-21943" rel="nofollow noopener">Wave Coasters</a></li><li>🗼 <a target="_blank" href="https://makerworld.com/en/models/251129#profileId-267476" rel="nofollow noopener">City Coasters</a></li><li>⛰️ <a target="_blank" href="https://makerworld.com/en/models/30652#profileId-27193" rel="nofollow noopener">Mountain Coasters</a></li></ul></li></ul>Licensing Information:<ul><li>These designs are for personal use only. To access them for commercial purposes and enjoy exclusive benefits, consider joining our Memberships. <a target="_blank" href="https://www.printables.com/@BamingoDesign#join:397" rel="nofollow noopener">Printables Memberships</a></li></ul>Stay Connected:<ul><li>Be the first to know about our newest designs by following us on Twitter and Instagram. Find all our social media links and more at <a target="_blank" href="http://bamingodesign.com/" rel="nofollow noopener">bamingodesign.com</a>.</li><li>We&#39;re excited to see your creations! Tag us when sharing photos of your prints and connect with us. Your feedback and requests are always welcome. 💙</li></ul>

Snowflake Coasters - Hueforge

Yuletide 

NC-Designs

Ever feeling indecisive about where to eat? Find yourself in a “no, where do YOU want to eat” battle with your spouse? Meet the Dinner Spinner!&nbsp;&nbsp;Make My Sign Info&nbsp;This model is powered by Make My Sign from MakerWorld (www.makerworld.com/en/makerlab/MakeMySign). Using Make My Sign and their SVG import tool, anyone can create additional logos or custom text for things like chores, activities, date night, games to play, etc. Most of the SVGs for the restaurants shown came from either <a target="_blank" href="https://worldvectorlogo.com/" rel="nofollow noopener">https://worldvectorlogo.com/</a> or <a target="_blank" href="https://commons.wikimedia.org/wiki/Category:SVG_logos_of_fast_food_restaurants#." rel="nofollow noopener">https://commons.wikimedia.org/wiki/Category:SVG_logos_of_fast_food_restaurants#.</a>&nbsp;To create your own logos or custom pieces to fit in the box, use the following settings in Make My Sign (these settings will minimize the amount of color changes as well):<ul><li>50mm x 50mm Shape</li><li>10mm Corner Radius</li><li>Medium Border with 0mm Offset</li><li>Thicknesses:<ul><li>Base Plate - 1mm</li><li>Text & Sticker - 0.2mm</li><li>SVG - 0.2mm</li><li>Shapes - 0.2mm</li></ul></li></ul>When you download a custom piece, I recommend downloading the 3MF file as it makes coloring much easier (don't color by face but color by part under the “Objects” tab instead). There are also some tricks I learned like using “Negative Part” type and deleting overlapping parts that come with the SVG to get the exact coloring you want.&nbsp;Assembly Instructions&nbsp;Each of the logos snap into place in the back of the dinner spinner. I recommend either:<ul><li>Printing all pieces except the logos, then one logo, and then scale the logo in ~0.1% increments until you get the fit you want. Then print the rest of the logos at the same scale.</li><li>Printing the logos you want and then the fitment test piece. Depending on that fitment you can adjust the scale in ~0.1% increments until you get the fit you want. Then scale the dinner spinner, spinner, spinner axis, and optional backing plate the same amount.</li></ul>There are spots for two 5mm x 2mm thick magnets (<a target="_blank" href="https://a.co/d/8JerZ9a" rel="nofollow noopener">https://a.co/d/8JerZ9a</a>) to be glued in each corner for putting it on the fridge. I ended up adding a third magnet to each corner that sticks out a little bit to make it more secure to the fridge.&nbsp;There is also an optional backing plate that has a cutout for mounting to a wall if wanted.&nbsp;&nbsp;Thanks for viewing, downloading, rating, etc. Any feedback is welcome!&nbsp;&nbsp;

The Dinner Spinner (20+ Logos Included)

Food Items 

Kopp3D

A trophy for World's Best Mom and World's Best Dad - makes a great gift for your loved one. Each prints in two pieces and the top one is slotted into the base (holds sturdy!) Scalable and reversable. Bases are printed on the side to only have one color change per plate.

World's Best Mom / Dad Trophies (topper slots in - only one color change!)

Because I love you 

MattInOregon

Give notice to the sorcerers and wizards in your life to summon demons elsewhere! And in case of an accidental summoning, provide a potion of freshening to counteract the aura of the demons they bring forth from the darkness.&nbsp;&nbsp;&nbsp;<ul><li>Two mounting holes integrated to fit Wall Dog drywall screws like these: <a target="_blank" href="https://www.amazon.com/Hillman-122367-Self-Drilling-Picture-Hanging/dp/B000ODQZZ2" rel="nofollow noopener">https://www.amazon.com/Hillman-122367-Self-Drilling-Picture-Hanging/dp/B000ODQZZ2</a> </li><li>Powered by Make My Sign from MakerWorld(makerworld.com/makerlab/MakeMySign)</li><li>Credit for Demon wings source image: <a target="_blank" href="https://freesvg.org/demon-wings" rel="nofollow noopener">https://freesvg.org/demon-wings</a></li><li>Credit for D20 source image: <a target="_blank" href="https://pixabay.com/vectors/d20-dice-game-nat20-dnd-d-d-7136921" rel="nofollow noopener">https://pixabay.com/vectors/d20-dice-game-nat20-dnd-d-d-7136921</a></li></ul>

Please Don't Summon Demons Bathroom Sign w/mount for your Potion of Freshening

Signs

The Crafty Maker

Introducing the first shadow box of another popular franchise, Harry Potter. Requested by one of my Patreon members. It depicts Harry, Hermione and Ron facing the evil Voldemort.&nbsp;I've used the following colors:<ul><li>Plate 1: R3D PETG Coffee</li><li>Plate 2: Overture Matte PLA Chocolate</li><li>Plate 3: Tinmorry PLA Silk Copper</li><li>Plate 4: Tinmorry PLA Silk Gold</li><li>Plate 5: PolyMaker PolyTerra PLA Peanut</li><li>Plate 6: Geeetech PLA White</li><li>Logo: Geeetech PLA Black + Geeetech PLA White (multicolor)</li></ul>The colors are just guidelines, you can get creative with the color scheme for a personal touch.&nbsp;It consists of 6 numbered plates. Plate number 1 comes in 2 different versions. One with the Harry Potter logo on it and one without the logo.&nbsp;I've added a Harry Potter logo that you can attach to the shadow box if you don't want to use plate number 1 with logo.&nbsp;You can find the box to display this set here: <a target="_blank" href="https://makerworld.com/en/models/13471" rel="nofollow noopener">https://makerworld.com/en/models/13471</a>&nbsp;The box with lid and the wall mountable box are both Patreon/Printables/Thangs subscriber exclusives. (Box with lid also available for individual purchase on <a target="_blank" href="https://cults3d.com/en/3d-model/art/shadow-box-with-lid-thecraftymaker" rel="nofollow noopener">Cults3D</a>)&nbsp;Print settings &nbsp;Plates<ul><li>No supports</li><li>100% infill</li><li>Arachne wall generator recommended </li><li>For smooth top finish you could use ironing or print, on smooth buildplate, face down.</li></ul>Logo<ul><li>Basic supports with top Z distance of 0.24 100% infill</li><li>Arachne wall generator recommended</li></ul>ALL The Crafty Maker designs are protected by Copyright Law. By downloading, YOU HAVE NO RIGHT to sell any digital files or reproductions from those files. If you want a commercial license to LEGALLY SELL 3D prints, you'll need a <a target="_blank" href="https://patreon.com/TheCraftyMaker" rel="nofollow noopener">The Crafty Seller Patreon</a> subscription.

Harry Potter Shadow Box (A)

Harry Potter 

&#34;If you&#39;re not with me, then you&#39;re my enemy.&#34; &#34;Only a Sith deals in absolutes. I will do what I must.&#34; &#34;You will try.&#34; ―Darth Vader and Obi-Wan Kenobi —&nbsp;Joining the Star Wars shadow boxes is this epic Duel on Mustafar shadow box.This is the first shadow box that has color swaps on almost every plate to make it even more epic.I&#39;ve used the following colors:<ul><li>Plate 1: Geeetech PLA Black</li><li>Plate 2: Tinmorry Matte Orange PLA swapped to R3D PETG Coffee</li><li>Plate 3: PolyMaker PolyTerra PLA Lava Red swapped to R3D PETG Coffee</li><li>Plate 4: R3D PETG Coffee swapped to PolyMaker PolyTerra PLA Lava Red</li><li>Plate 5: Fillamentum PLA Extrafill Luminous Orange swapped to PolyMaker PolyTerra PLA Lava Red</li><li>Logo: Geeetech PLA Black + Geeetech PLA White (multicolor)</li></ul>The colors are just guidelines, you can get creative with the color scheme for a personal touch.&nbsp;It consists of 5 numbered plates.&nbsp;I&#39;ve also added a Star Wars logo that you can attach to the shadow box.&nbsp;You can find the box to display this set here: <a target="_blank" href="https://makerworld.com/en/models/13471" rel="nofollow noopener">https://makerworld.com/en/models/13471</a>&nbsp;The box with lid and the wall mountable box are both Patreon/Printables/Thangs subscriber exclusives. (Box with lid also available for individual purchase on <a target="_blank" href="https://cults3d.com/en/3d-model/art/shadow-box-with-lid-thecraftymaker" rel="nofollow noopener">Cults3D</a>)&nbsp;Print settings &nbsp;Plates<ul><li>No supports</li><li>100% infill</li><li>Arachne wall generator recommended </li><li>Swap color at the start of layer 6</li></ul>Logo<ul><li>Basic supports with top Z distance of 0.24 </li><li>100% infill</li><li>Arachne wall generator recommended</li></ul>ALL The Crafty Maker designs are protected by Copyright Law. By downloading, YOU HAVE NO RIGHT to sell any digital files or reproductions from those files. If you want a commercial license to LEGALLY SELL 3D prints, you&#39;ll need a <a target="_blank" href="https://patreon.com/TheCraftyMaker" rel="nofollow noopener">The Crafty Seller Patreon</a> subscription.

Star Wars Duel On Mustafar Shadow Box

Star Wars

Satisartes

Cute gnomes to decorate your home.

gnomes in sleigh

Gnomes 

Madtrap

<h2>Pistachio Bowl Final version.</h2>Updates:2024-06-06<ul><li>Redesigned the outer bowl to allow more space for shells and avoid build-up.</li></ul><img class="image_resized" style="width: 23.19%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000091140/design/2024-06-06_b2e909324e3d7.png">  2024-02-17: <ul><li>Added print profile for detached flower based on community feedback</li><li>Simplified polygons in CAD to make model slice faster</li><li>added chamfer to inner tube on inner bowl to make shells go in easier</li><li>fixed offset dot on flower (Thanks <a target="_blank" href="https://makerworld.com/en/u/2862399193" rel="nofollow noopener">@Nicolinux</a>)</li><li>general fixes on print profile</li></ul> 2024-01-04: Tried to add fix so people downloading the model will get the lastest version instead of old one. 2023-12-24: Tulip Bowl added. 2023-12-16: version 1.2 I didn&#39;t like the fit of the bowl on the first couple of versions, so in version 1.2 I have reworked the shape of the inner and outer bowl to fit perfectly on each other with out slipping around which were an issue with first versions.(edit: 2023-22-12: fixed bad grammar)  A mario themed bowl for pistachios. Use the top bowl for the nuts and bottom one for the shells. Just yeet the shells into the mouth of the Piranha Plant.&nbsp;Happy Printing.&nbsp;Me and my brother spend time on this for our own enjoyment and just want to share our work with the community.If you like any of our models we would appreciate a comment or upvote on the model you like. Also, always feel free to contact us if you have any suggestions for new or current models. If you want to buy us a coffee use our <a target="_blank" href="https://paypal.me/madtrap" rel="nofollow noopener">Paypal</a>

Pistachio Bowl Final Version

Super Mario

Set of 3 bookmarks with Celtic Dragon Knotwork designs. &nbsp;Please share your prints.&nbsp;&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm&nbsp;Swap Instructions: Start with Black At layer #3(0.32mm) swap to Dark Grey At layer #7 (0.64mm) swap to Light Grey At layer #9 (0.80mm) swap to White

Celtic Dragon Knot Designs - Set of 3 Bookmarks

dragons 

Uncle Jessy

Here is your chance to take down the Empire with your new A1 fighter! Aim for the Thermal Exhaust Port! I figured I'd try to make a fun Purge bucket for your A1 that will print directly on the buildplate without any supports. There are two print options currently. 1 that is plain, and the other that has the small opening for your filament purge poo to try and fling through.&nbsp;I modeled this in Shapr3D on my ipad and was a fun little project. I might make more mods to this as well as more design updates to it.&nbsp;The print top should be level with the top of the A1 & it should line up properly but not cover the side speakers. &nbsp;This was a quick 3-4 hour print.No supports needed.2 or .28 layer height3 bottom 3 top should be fine along with 10% infill&nbsp;Let it rip and have fun! If you print one make sure to tag me online. I'd love to see them! @UncleJessy / @UncleJessy4Real&nbsp;You can see the purge bucket in action here in my A1 Printer video&nbsp;<figure class="media"><div data-oembed-url="https://youtu.be/K8n-KQyMS9w"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/K8n-KQyMS9w" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>