Waldtroll

bodenseefisch

I modified the AMS Lite for my Ikea Lack enlosure to keep the filament dry.&nbsp;You can use it in any way you want with minimum space requirement. In my case i added them at the top of an ikea lack enclosure.These parts are remixes by <a target="_blank" href="https://www.printables.com/de/model/4577-drybox-for-prusa-printer-enclosure-v2-without-humi" rel="nofollow noopener">Prusa Drybox</a> and <a target="_blank" href="https://www.printables.com/de/model/184236-baseholder-for-standalone-drybox" rel="nofollow noopener">Drybox Mount</a>.All drybox are mirrored to simply access it from the front to get out the filament very easily.The boxes can be snap in to the mount to connect the led power. Furthermore it is very stable if you handle with filament. I remixed them, so you can print these parts very fast.To disassemble the AMS lite, you have to loosen few screws and pin cables. Look at the bambu lab tutorial <a target="_blank" href="https://www.youtube.com/watch?v=DAge2NaxOUg&amp;t=116s" rel="nofollow noopener">here</a> or <a target="_blank" href="https://wiki.bambulab.com/en/ams/maintenance/ams-lite-com" rel="nofollow noopener">here</a>. It’s very easy. Dont worry, the AMS will work normally and the RFID antenna, resp. Retraction spring is not needed, because the filament will continue retract normally. It works flawlessly.You need following parts:<ul><li><a target="_blank" href="https://www.amazon.de/dp/B09WMRDRR8?ref=ppx_yo2ov_dt_b_product_details&amp;th=1" rel="nofollow noopener">Touch Dimmer Switch</a> (optional)</li><li><a target="_blank" href="https://www.amazon.de/dp/B0C5XBDJYV?psc=1&amp;ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">8x PC4-M10 PTFE Connector</a>s</li><li><a target="_blank" href="https://www.amazon.de/dp/B0CMK5GYCP?psc=1&amp;ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">4x DC Mount Power Adapters / Power Jack socket</a>s</li></ul>Gently push and/or mount the connectors into the bottom mount. I recommend hot glue or seal it with a 3D Pen, so that the male adapter is firmly fixed.Optional further parts:<ul><li>A spool Holder and fake bearing get it from <a target="_blank" href="https://www.printables.com/de/model/74378-tush-for-drybox/files" rel="nofollow noopener">here</a>. </li><li> I dont recommend a silica container at the bottom, because it‘s awkward. If you want to use extra portion silica gel, i recommend that you fill it directly into the box. Anyway, i used <a target="_blank" href="https://makerworld.com/en/models/179426#profileId-197392" rel="nofollow noopener">this one</a> inside the spool. </li><li>An AMS Lite tube coupler you can find <a target="_blank" href="https://makerworld.com/en/models/81895#profileId-87149" rel="nofollow noopener">here</a>.</li><li>Temperature and humidity sensor <a target="_blank" href="https://www.amazon.de/dp/B08KWCFSXN?psc=1&amp;ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">here</a>. </li><li>And 8x <a target="_blank" href="https://www.amazon.de/dp/B075SHDKKL?psc=1&amp;ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">M3x40</a> screws recommended for the dryboxes.</li><li><a target="_blank" href="https://eu.store.bambulab.com/de/collections/spare-parts-for-ams/products/bambu-ptfe-tube-3-pcs-x1-series-and-p1s?variant=46984157397340" rel="nofollow noopener">PTFE tube</a></li></ul>I added a tool to cut the window. I recommend PET foil from a local craft market or just use some bulletproof display glass from your smartphone. Enjoy the new way of AMS printing!

AMS Lite Hexagon Drybox - LED MOD

K2_Kevin

<h3>BAMBU HexScraper MINI w/Replaceable Blades</h3>&nbsp;The Bambu HexScraper Mini is here! It comes with a reduced handle size and replaceable blade, making it ideal for scraping off small parts. I hope you find it truly satisfying! Print the 2 Color logo version for a nice “faceplant” two-sided logo.&nbsp;UPDATE: Added 101% Scaled Blade profiles for tighter fit. Let me know…&nbsp;⭐️Don&#39;t forget to Follow! Thank you so much for your Downloads, Like and BOOSTS!&nbsp;BLADE PRINTING HINTS:<ul><li>Blade Sizing: You may need to scale the X/Y 101% or higher using some filaments for tighter fit.</li><li>Blades are best printed at 0.12 layer height for a sharper edge.</li><li>Blades printed in PETG, ABS, ASA are recommended for strength</li><li>Blades should be very tight when first installing, your print will generally shrink.</li></ul><h3>Please don&#39;t forget to ❤ Like and ★ Rate!</h3>&nbsp;Also checkout the Gridfinity Hex Scraper Holder&nbsp;&nbsp;&nbsp;&nbsp;

Hex Scraper MINI w/Replaceable Blade

Gridfinity

justfourprint

Eine Balkonhalterung (Größe 30-40mm) für Tomatenstangen&nbsp;Benötigt wird:2x Zylinderkopfschraube M6x25-302x Mutter M6

Balkon_Tomatenstangen_Halterung

Garten 

Makerillo

Bambu Swatch Box for storing your samples&nbsp;I made this box for storing this samples:<a target="_blank" href="https://makerworld.com/en/models/65879#profileId-69212" rel="nofollow noopener">https://makerworld.com/en/models/65879#profileId-69212</a>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/227917/2023-12-02_2f4b007494642.jpg"></figure>

Bambu Swatch Box

Filament 

ThreeD-Michael

<figure class="table" style="width:78%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td style="width:50%;" colspan="2">If you like this design, please also check out my new <a target="_blank" href="https://makerworld.com/en/models/231936" rel="nofollow noopener">Optimized Bed Scraper</a>:</td></tr><tr><td style="text-align:center;width:50%;"><figure class="image"><a href="https://makerworld.com/en/models/231936" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/654792/2024-03-07_4670d91a31e1a.png"></a></figure></td><td style="text-align:center;width:50%;"><figure class="image"><a href="https://makerworld.com/en/models/231936" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/654792/2024-03-07_30f7514113eb6.jpg"></a></figure></td></tr></tbody></table></figure><figure class="table" style="width:78%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td style="width:50%;" colspan="2">Update: Upon request, I uploaded the poop buckets I use: <a target="_blank" href="https://makerworld.com/en/models/156253" rel="nofollow noopener">BambuLab A1</a>, <a target="_blank" href="https://makerworld.com/en/models/156091" rel="nofollow noopener">BambuLab A1 Mini</a>.</td></tr><tr><td style="text-align:center;width:50%;"><figure class="image"><a href="https://makerworld.com/en/models/156253" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/654792/2024-01-25_e31ca8915fbc3.jpg"></a></figure></td><td style="text-align:center;width:50%;"><figure class="image"><a href="https://makerworld.com/en/models/156091" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/654792/2024-01-25_ba2d0a197944.jpg"></a></figure></td></tr></tbody></table></figure>Poop Deflector for Bambulab A1 and A1 MiniI know there are already poop deflector designs online. I tried a few but didn't like them because they were either too brittle and/or lacked a proper attachment. That's why I created my own design, which offers the following advantages:<ul><li>secure fixation,</li><li>stabilized deflector,</li><li>stable walls,</li><li>easy and quick printing,</li><li>only 4g weight.</li></ul>Since I've been using this deflector, no poop has missed the basket...&nbsp;Assembly:Carefully click the poop deflector onto the purge wiper. Place a collecting container under the deflector and make sure that the deflector cannot touch the container in the lowest z position of the printer.

Poop Deflector (A1 + A1 Mini)

Drucker

BamBam Design

<h4>Toroidal Windmill - Self adjusting turbine</h4>Looks like a spinning flower and no much wind is needed.<a target="_blank" href="https://youtube.com/shorts/WrKHW2Cdyvk?si=byQ_EpJAfOOy8x7F" rel="nofollow noopener">YouTube Short</a>&nbsp;<ul><li>Beautiful Windmill with toroidal Propeller Blades</li><li>Self adjusting to wind direction (Tail Blade Reworked)</li><li>100% printed, no Screws or tools needed</li><li>You can add 3 Propellers on one Axle with 2 distances</li><li>Full customizable with different propeller sizes and directions (I plan to add more cool propeller types as well)</li><li>Rods are stack able to your needed height</li></ul><h4>Printing:</h4>You can choose Propellers from 3 Print Profiles<ul><li>Basic Parts with Left&amp; Right Propeller to choose</li><li>Additional Propeller Blades</li><li>Additional Slower Propeller *New</li></ul>You can mix the propellers from these profiles.<ul><li>added one profile for A1mini without the biggest blade as well</li></ul>The rod could be a bit difficult to print, i added custom support, but clean your buildplate and apply some glue.&nbsp;PETG &amp; PLA tested👍🏼<h4>Assembly:</h4><h4>Info:</h4><ul><li>Added custom support to the horizontal printing rod</li><li>Added optional longer axle for more distance between propellers (10mm instead of 5mm).  With stronger wind the bigger blades should not collide.</li></ul>The Pitch from the Basic Blades:<ul><li>Big - Pitch 195mm</li><li>Med - Pitch 170mm</li><li>Small - Pitch 135mm</li></ul>Additional Propeller Blades with different numbers of Wings:<ul><li>Big - Pitch 190mm</li><li>Med - Pitch 160mm</li><li>Small - Pitch 130mm</li></ul>Additional “Slower” Propeller Blades:<ul><li>Big - Pitch 400mm</li><li>Med - Pitch 325mm</li><li>Small - Pitch 250mm</li></ul>Thanks to all followers and don&#39;t forget the virtual handshake 👍 ….Happy Printing&nbsp;Info II:My other windmills are fully compatible if you want to mix it up:<ul><li><a target="_blank" href="https://makerworld.com/models/235261" rel="nofollow noopener">Toroidal Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/250216" rel="nofollow noopener">Honeycomb Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/388124" rel="nofollow noopener">Elliptical Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/425419" rel="nofollow noopener">Sunflower Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/454861" rel="nofollow noopener">Raccoon Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/255324" rel="nofollow noopener">CLAMP for Windmills</a></li></ul>Info III:More modifications you find on my Patreon account.<figure class="image"><a href="https://www.patreon.com/posts/mod-608-bearing-105175595" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000235261/design/2024-05-30_3ad9786c3df1b.png"></a></figure>&nbsp;<figure class="image"><a href="https://www.patreon.com/posts/mod-pole-adapter-103628897" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000235261/design/2024-05-30_70c92ad1f54a9.png"></a></figure>&nbsp;Commercial license you can get here:<a target="_blank" href="https://www.patreon.com/BamBamDesign/membership" rel="nofollow noopener">https://www.patreon.com/BamBamDesign/membership</a>

Toroidal Windmill - Customizable system

Allg.

squinn

A portable cable organizer which is setup as an easy print-in-place and includes a knob on the side for conveniently winding up the cable when you're ready to pack it away.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/76375/2023-09-13_fd01d80e216de.gif"></figure>This model is an easy print that requires no supports, and three different sizes are provided to accommodate cables of different lengths. If you're not sure which to choose, I'd recommend starting with the “medium” size.&nbsp;After printing, you'll want to place the cable within the groove at its halfway point, close the lid (which is intentionally designed to close tightly), wind up the cord clockwise using the handle, and then extend by simply grabbing the cable by both ends.&nbsp;Update 2023-09-13:&nbsp;Alternative smooth-sided versions of all three sizes have now been added, and also the handle design was slightly adjusted to add a small fillet and chamfer to decrease the bridge distance. Here's a close-up picture of the updated handle on the knurled and smooth-sided versions:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/76375/2023-09-13_e75ea621224d08.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/76375/2023-09-13_68f2b35a6774b8.jpg"></figure>&nbsp;

Portable Cable Organizer / Winder

warlogh

Modular Corner Jig with option of changing corner Radius Inserts.&nbsp;How it works? Very simple! Just choose insert with needed Radius, put it together with Main Jig Body and secure the insert with a Lock screw. Main Body has a threaded hole for Lock Screw to keep it together when you are not using a Jig.&nbsp;Jig corner insert Radius sizes in this set:<figure class="table" style="width: 714px"><table><tbody><tr><td style="background-color: rgb(249, 205, 66); border: 1px solid rgb(0, 0, 0); padding: 0.4em; text-align: center">METRIC</td><td style="background-color: rgb(249, 205, 66); border: 1px solid rgb(0, 0, 0); padding: 0.4em; text-align: center">IMPERIAL</td></tr><tr><td style="background-color: rgba(249, 205, 66, 0.094); border: 1px solid rgb(0, 0, 0); padding: 0.4em; text-align: center">5mm 10mm 15mm 20mm 25mm 30mm 35mm 40mm</td><td style="background-color: rgba(249, 205, 66, 0.094); border: 1px solid rgb(0, 0, 0); padding: 0.4em; text-align: center">5/16&#34; 5/8&#34; 0.25&#34; 0.5&#34; 0.75&#34; 1&#34; 1.25&#34; 1,5&#34; 1,75&#34;</td></tr></tbody></table></figure>If You need different size, give me a shout and I&#39;ll make it for you.&nbsp;Here are separate profiles for Main Body and inserts (+screw) Profiles. For inserts and Screw, supports are NOT needed. For main body , they are not necessary as well, but I would advise to use Supports, but paint them away from threaded Hole.&nbsp;28.06.2024 Update<ul><li>Added 5mm Radius Insert STL and Profile as requested</li><li>Added Imperial Unit Radius Inserts</li></ul>19.04.2024 Update<ul><li>Added Changeable insert Lock Screw without Cap so You can use a Jig with a router with bigger base. All You need is a Philips Screwdriver.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000410156/design/2024-04-19_bed6e2d55a693.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000410156/design/2024-04-19_5bdf6fe4f17f3.jpg"></figure>You can find it in STL files here.&nbsp;That&#39;s it. Quite simple I guess.&nbsp;&nbsp;You can Buy me a coffee if You feel good doing so :)<a target="_blank" href="https://www.buymeacoffee.com/warlogh" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000410156/design/2024-03-16_5923e8a1a0113.jpg"></a> <a target="_blank" href="https://www.buymeacoffee.com/warlogh" rel="nofollow noopener">https://www.buymeacoffee.com/warlogh</a>(And very Big Thank You For interest in my work)

AMS

Gridfinity

Garten

Filament

Drucker

Allg.

box

Wekstatt