CS&E

AnnIsMax俺叫Max

&nbsp;This mouse uses a “VXE R1 SE” gaming mouse's internal electronics as the inner workings.本项目使用 “VXE R1 SE” 鼠标的电路板作为内核&nbsp;Extra hardware: 额外五金件：&nbsp; (3x) m3*6 hex screw (3x) m3*6 内六角螺丝钉 (3x) m3*4*4.2 heat set inserts (3x) m3*4*4.2 滚花螺母&nbsp; (1x) Omron B3F-4055(12*12*7.3) tactile switch (1x) Omron B3F-4055(12*12*7.3) 轻触开关 (2x) Omron B3F-6052(6*6*7.3) tactile switch (2x) Omron B3F-6052(6*6*7.3) 轻触开关&nbsp; (many x) Mouse Feet (任意x) 鼠标脚垫&nbsp;&nbsp;Installation Tips:安装提示：<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/351432/2024-01-04_db0a1801d4a4c.jpg"></figure>Cut away the protruding “flag shaped” bit from the 6*6 tactile switches.将6*6 轻触开关上的“旗型” 突起如图所示修剪掉&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/351432/2024-01-04_d02c743011195.jpg"></figure>Insert tactile switches as shown. （solder the wires onto the switches before hand）如图所示安装开关 (先将导线焊至开关上会更容易安装)&nbsp;&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/351432/2024-01-04_0bcc53a4ce9a7.jpg"></figure>Add heat set inserts in to the Body parts as shown.在背部底端3个孔洞处用烙铁加上滚花螺母&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/351432/2024-01-04_0987064e7ed1d.jpg"></figure>Cut away all excess bits from the encoder as shown in the picture.Install the encoder in the opposite direction comparing to the the original direction on the board. (protruding blue ring should face the wheel)将编码器取下后切除多余的金属部分（结果见图）安装编码器时旋转180度（侧面突出的蓝色环应接触滚轮）&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/351432/2024-01-04_debeceb9f7ed1.png"></figure>&nbsp;Because the encoder has been turn around, exchange the wiring of the “A” and “B” Pins (or the wheel will scroll the screen in the opposite direction)因为编码器旋转了180度， “A” 和 “B” 脚的接线需要调换（不然滚轮输入会反过来）<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/351432/2024-01-04_ef1be30b92a2a.jpg"></figure>Install the micro switches here.将微动开关安装在篮圈所示位置&nbsp;Align these 3 holes from the logic board to both the body and base parts then tighten with screws from the underside.将底板，背板和电路板上的红圈处3孔对齐上螺丝。&nbsp;&nbsp;Misc:&nbsp;2 sizes of side buttons were provided, install them to your liking.侧边前进后退按键提供了2个高度，可根据自己喜好打印安装

Max's Ergonomic Mouse (using VXE R1 SE's internal electronics)

Hayden’s stuff 

Roman

Spool Stand designed for the bambu labs refillable spools. For storing spools upright on a shelf to stop them rolling away. Each stand has slots for an additional spool so the stand system can be extended.

Hayden’s stuff

handy things to print